scholarly journals High-sensitivity SO2 Gas Sensor Based on Noble Metal Doped WO3 Nanomaterials

2021 ◽  
pp. ArticleID:211240
Author(s):  
Hang Liu ◽  
2008 ◽  
Vol 112 (48) ◽  
pp. 12355-12366 ◽  
Author(s):  
B. W. Ticknor ◽  
B. Bandyopadhyay ◽  
M. A. Duncan

2005 ◽  
Vol 486-487 ◽  
pp. 485-488 ◽  
Author(s):  
Hong Quang Nguyen ◽  
Mai Van Trinh ◽  
Jeung Soo Huh

The effect of operating temperature on characteristics of single-walled carbon nanotubes (SWNT) based gas sensor was investigated. SWNT-based sensor was fabricated from SWNT powder (Iljin Nanotech, Korea) by screen-printing method. SWNT powder (30 mg, AP grade) was dispersed into 0.78 gram a-terpineol (Aldrich) by ultrasonic vibration for 1 hour then stirred manually for 1 hour to increase adhesion. From this condensed solution, a thick film of SWNT was printed onto alumina substrates. The film then was sintered at 300oC for 2 hours to remove residual impurities. Upon exposure to some gases such as nitrogen, ammonia or nitric oxide, resistance of the sensor dramatically changes due to gas adsorption. In our experiments, SWNT-based sensor was employed to detect NH3 gas in N2 ambience. After saturated of N2, the sensor exposes to NH3 with various concentrations (from 5 ppm to 100 ppm, diluted by N2 as carrier gas). This sensor exhibits a fast response, high sensitivity but slow recovery at room temperature. By heating at high temperature and increasing the flow-rate of carrier gas, NH3 gas desorbs easily and recovery of the sensor improved. The heating also influenced the characteristics of sensors such as response and reproducibility. Other special changes in electric property of SWNT-based sensor caused by heating are also discussed.


2021 ◽  
pp. 2101511
Author(s):  
Ziwei Chen ◽  
Haojie Guo ◽  
Fusheng Zhang ◽  
Xiaowen Li ◽  
Jiabing Yu ◽  
...  

ACS Sensors ◽  
2021 ◽  
Vol 6 (9) ◽  
pp. 3387-3397
Author(s):  
Haoxuan He ◽  
Chenxi Zhao ◽  
Jing Xu ◽  
Kuanzhi Qu ◽  
Zhen Jiang ◽  
...  

Author(s):  
Hu Huang ◽  
Jian-Song Zhang ◽  
Weiling Luan ◽  
Shan-Tung Tu ◽  
Shang-Kuo Yang

TE (Thermoelectric) materials have been widely used in clean energy system as low-power generator and Peliter cooler, due to its salient features of being compact, light-weighted, noiseless in operation, highly reliable, and environment friendly. Recently, another application has been explored on TE materials as gas sensors based on Seebeck effect and exothermic reaction of hydrogen oxidation on catalyst. In this paper, a TE hydrogen gas sensor with a simple structure, low energy consumption and a high sensitivity was reported. Bi-Te (bismuth telluride) with a high Seebeck coefficient at room-temperature was deposited onto thin glass substrates by RF magnetron sputtering technology. Four pairs of PN film couples were connected in series to improve the output voltage. Pt/ ACC (Activated Carbon Fiber Cloth) was mounted at the joint of PN couples, acting as catalyst so as to accelerate the oxidation of hydrogen. The influences of reduction temperature and Pt content on the generated temperature difference were investigated. The voltage output and selectivity to combustible gas mixture were measured. Experimental results showed that when exposed to 3vol% H2/ air, as-prepared sensor gave out a high output signal of 33.1mV, and the response time was about 50s with recovery time of 50s.


Author(s):  
Monika Kwoka ◽  
Michal A. Borysiewicz ◽  
Pawel Tomkiewicz ◽  
Anna Piotrowska ◽  
Jacek Szuber

In this paper a novel type of a highly sensitive gas sensor device based on the surface photovoltage effect is described. The developed surface photovoltage gas sensor is based on a reverse Kelvin probe approach. As the active gas sensing electrode the porous ZnO nanostructured thin films are used deposited by the direct current (DC) reactive magnetron sputtering method exhibiting the nanocoral surface morphology combined with an evident surface nonstoichiometry related to the unintentional surface carbon and water vapor contaminations. Among others, the demonstrated SPV gas sensor device exhibits a high sensitivity of 1 ppm to NO2 with a signal to noise ratio of about 50 and a fast response time of several seconds under the room temperature conditions.


2021 ◽  
Author(s):  
Jeffery Alexander Powell

Raman spectroscopy is a powerful tool for detection of chemical and bioanalytes but lacks enhancement required to detect these analytes at the ultrahigh sensitivity needed for many applications. Surface enhanced Raman Scattering is a technique by which an analyte signal can become greatly enhanced and, near single molecule sensitivity, is achievable. Currently, SERS-based detection platforms currently rely on noble metal nanostructures as primary enhancing sources for the detection of chemical and bioanalytes but have significant limitations in terms of reproducibility and biocompatibility. Recent research has shown that semiconductors have the ability to exhibit SERS enhancing characteristics that can potentially supplant the use of noble metals without the limitations associated with noble metal nanomaterials. This thesis presents, the generation of three-dimensional self-assembled hybrid silicon nanostructures though a laser-ion plume formation mechanism. These Si nanostructures exhibit high sensitivity SERS enhancement characteristics which can be applied for chemical and biosensing applications. In this thesis, the Raman enhancing characteristics of the hybrid Si nanostructures are examined and correlated to the unique physical morphology and material chemistry of these nanostructures. These Si nanostructures are shown to be comprised of individual Si nanospheroids that have fused to form a highly 3D nanoweb-like self-assembled nanostructures. It is also shown that these nanospheroids are composed of both amorphous and polycrystalline sub-regions, which can only be generated within an ion-plume formed by a femtosecond pulsed laser. By programming the laser, the nanostructure morphology and hybrid nature can be manipulated and optimized. These Si nanostructures are shown to be highly sensitive as SERS platforms for chemical analytes. In addition, it is shown that with the application of noble metal nanoparticles on the surface of the 3D hybrid silicon nanowebs structures, an additional enhancement boost can be optimized for the detection of chemical molecules. With this, the dual contribution to the SERS sensitivity from both the primary Si nanostructures and the secondary noble metal nanostructures can be used to detect the presence of a biomolecule analyte is shown. To delve deeper into how these hybrid Si nanostructures cause SERS enhancement of bioanalytes, the Si ion interactions within the laser-ion plume were manipulated to induce quantum-scale defects within the hybrid Si nanospheroids. By creating both an inert and oxygenated laser-ion plumes the formation of sub-nanograins within the nanospheroids and sub-nanovoids on the nanospheroid surface is shown to significantly enhance the detection of bioanalyte signal for multiple biomolecules which act as signals for various diseases. Based on the results in this thesis, it has been proven that Si-based nanostructures have the capacity to be used as sole SERS enhancing sources for chemical and biomolecule analytes.


Sign in / Sign up

Export Citation Format

Share Document