scholarly journals Removal of Chrysoidine Y from water by Graphene-based Nanocomposite Derivatives with Magnetic Chitosa Nanocomposite

2019 ◽  
Vol 4 (02) ◽  
pp. 17-33
Author(s):  
Farid Abu Shammala ◽  
Barry Chiswell
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Maximum Adsorption Capacity ◽  
Order Model ◽  
Intraparticle Diffusion Model ◽  
First Order ◽  
Transmission Electron ◽  
Pseudo Second Order ◽  
Adsorption Kinetics And Isotherm ◽  
Nanocomposite Adsorbent

This article describes a novel and efficient MCTS/GO nanocomposite for the accumulation and removal of a hazardous azo dye (Chrysoidine Y) from its aqueous solutions. Magnetic Chitosan /graphene oxide (MCTS/GO) nanocomposite adsorbent was prepared by wet-spinning technique, was used as accumulation and removal of Chrysoidine Y from aqueous solution. The structure and morphology of MCTS/GO nanocomposites were investigated using transmission electron microscope (TEM) and Fourier transform infrared (FTIR) spectroscopy were carried out on the MCTS/GO before the Chrysoidine Y (CY) accumulation experiments. The adsorption kinetics and isotherm studies were conducted under different conditions (pH = 3-7 and CY concentration = 100-400 mg/L) to examine the accumultion efficiency of the MCTS/GO towards CY in aqueous solution. The kinetics data of the adsorption process were analyzed using different kinetic models in order to investigate the adsorption behavior of CY on MCTS/GO. The results showed that the maximum adsorption capacity of the MCTS/GO nanocomposites towards CY can achieve up to ~700 mg/g for the adsorption at 300 mg/L CY. Kinetic data of adsorption process were found to fit pseudo-second order model as compared with pseudo-first-order model. The intraparticle diffusion model suggested that the adsorption process of MCTS/GO towards CY was dominated by the external mass transfer of CY molecules to the surface of MCTS/GO.

Preparation of bio-based magnetic adsorbent and application for efficient removal of Cd(II) from water

2018 ◽  
Vol 77 (5) ◽  
pp. 1313-1323 ◽  
Author(s):  
Jianjun Zhou ◽  
Xionghui Ji ◽  
Xiaohui Zhou ◽  
Jialin Ren ◽  
Yaochi Liu
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Low Cost ◽  
Maximum Adsorption Capacity ◽  
Magnetic Adsorbent ◽  
Order Model ◽  
Efficient Removal ◽  
Adsorption Ability ◽  
Adsorption Sites ◽  
Pseudo Second Order

Abstract A novel magnetic bio-adsorbent (MCIA) was developed, characterized and tested for its Cd(II) removal from aqueous solution. MCIA could be easily separated from the solution after equilibrium adsorption due to its super-paramagnetic property. The functional and magnetic bio-material was an attractive adsorbent for the removal of Cd(II) from aqueous solution owing to the abundant adsorption sites, amino-group and oxygen-containing groups on the surface of Cyclosorus interruptus. The experimental results indicated that the MCIA exhibited excellent adsorption ability and the adsorption process was spontaneous and endothermic. The adsorption isotherm was consistent with the Langmuir model. The adsorption kinetic fitted the pseudo-second-order model very well. The maximum adsorption capacity of Cd(II) onto MCIA was 40.8, 49.4, 54.6 and 56.6 mg/g at 293, 303, 313 and 323 K, respectively. And the MCIA exhibited an excellent reusability and impressive regeneration. Therefore, MCIA could serve as a sustainable, efficient and low-cost magnetic adsorbent for Cd(II) removal from aqueous solution.

scholarly journals Preparation of Synthetic Clays to Remove Phosphates and Ibuprofen in Water

Water ◽  
2021 ◽  
Vol 13 (17) ◽  
pp. 2394
Author(s):  
Rosa Devesa-Rey ◽  
Jesús del Val ◽  
Jorge Feijoo ◽  
José González-Coma ◽  
Gonzalo Castiñeira ◽  
...  
Keyword(s):  
Close Agreement ◽  
Adsorption Process ◽  
Intraparticle Diffusion ◽  
Phosphate Adsorption ◽  
Order Model ◽  
Intraparticle Diffusion Model ◽  
First Order ◽  
Pseudo Second Order ◽  
Double Hydroxide ◽  
Phosphate Desorption

The main objective of this study consists in the synthesis of a layered double hydroxide (LDH) clay doped with magnesium and aluminum in order to test the removal of phosphates and ibuprofen in water. Two different LDH composites are assessed: oven-dried (LDHD) and calcined (LDHC). Single adsorptions of phosphate and ibuprofen showed up to 70% and 58% removal in water, when LDHC was used. A poorer performance was observed for LDHD, which presented adsorption efficiencies of 52% and 35%, respectively. The simultaneous removal of phosphate and ibuprofen in water showed that LDHC allows a greater reduction in the concentration of both compounds than LDHD. Phosphate adsorption showed a close agreement between the experimental and theoretical capacities predicted by the pseudo-second-order model, whereas ibuprofen fitted to a first-order model. In addition, phosphate adsorption showed a good fit to an intraparticle diffusion model and to Bangham model suggesting that diffusion into pores controls the adsorption process. No other mechanisms may be involved in ibuprofen adsorption, apart from intraparticle diffusion. Finally, phosphate desorption could recover up to 59% of the initial concentration, showing the feasibility of the recuperation of this compound in the LDH.

scholarly journals A slow pyrolysis biochar derived from Tetrapanax papyriferum petiole as an effective sorbent for removing copper ions from aqueous solution

BioResources ◽  
2019 ◽  
Vol 14 (2) ◽  
pp. 4430-4453
Author(s):  
Wenqi Li ◽  
Liping Zhang ◽  
Ying Guan ◽  
Zhihan Tong ◽  
Xiang Chen ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Adsorption Mechanism ◽  
Adsorption Process ◽  
Copper Ions ◽  
Maximum Adsorption Capacity ◽  
Transmission Electron ◽  
Tetrapanax Papyriferum ◽  
Pseudo Second Order ◽  
Nanopore Structure ◽  
Effective Sorbent

Biochar derived from Tetrapanax papyriferum petioles at different pyrolysis temperatures was used to remove copper from aqueous solution. Abundant porous structures were observed with scanning electron microscopy, and transmission electron microscope images revealed a unique layered nanopore structure. A high pyrolytic temperature resulted in a biochar with a higher surface area, ash content, and mineral element content. The maximum adsorption capacity of T. papyriferum petiole biochar (TBC) was 182 mg/g. The Langmuir adsorption isotherm model and pseudo-second-order kinetics model were most suitable for describing the adsorption process, indicating that adsorption takes place at specific homogeneous sites within the adsorbent. The calculated ΔH° values indicated that the adsorption process was endothermic. The adsorption mechanism for TBC was attributed to precipitation, ion exchange, C-π interactions, and complexation. Thus, the biochar used in this study is a promising environmentally friendly and effective adsorbent for removing Cu2+ ions from an aqueous solution.

scholarly journals COMPARISON OF STINGING NETTLE ADSORPTION PERFORMANCE TOWARDS ANIONIC AND CATIONIC DYES

2021 ◽  
Vol 55 (9-10) ◽  
pp. 1131-1142
Author(s):  
BENGÜ ERTAN ◽  
Keyword(s):  
Adsorption Process ◽  
Adsorption Equilibrium ◽  
Maximum Adsorption Capacity ◽  
Order Model ◽  
Stinging Nettle ◽  
First Order ◽  
Equilibrium Data ◽  
Pseudo Second Order ◽  
Adsorption Equilibrium Data ◽  
Cr Uptake

Stinging nettle was used as lignocellulosic adsorbent for the removal of cationic dye – malachite green (MG), and anionic dye – Congo red (CR), from aqueous solution, without any chemical pretreatment. The adsorption equilibrium data fitted well with the Langmuir model for the adsorption of both dyes, with the calculated maximum adsorption capacity of 270.27 mgg-1 and 172.14 mgg-1 for MG and CR, respectively. The adsorption process was controlled by the pseudo-second-order model in the adsorption of MG and by the pseudo-first-order model in the adsorption of CR. The thermodynamics modelling displayed that the process was spontaneous and endothermic. The π–π electron–donor interaction, hydrogen bonds and pore diffusion may also be effective, besides electrostatic interaction between the adsorbate and the adsorbent in the mechanism of MG and CR uptake.

scholarly journals RGO/CNF/PANI AS AN EFFECTIVE ADSORBENT FOR THE ADSORPTION OF URANIUM FROM AQUEOUS SOLUTION

2018 ◽  
Vol 56 (1A) ◽  
pp. 25
Author(s):  
Nguyen Quang Dat
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Adsorption Process ◽  
Uranium Concentration ◽  
Maximum Adsorption Capacity ◽  
High Adsorption ◽  
Order Model ◽  
Pani Composite ◽  
Reduced Graphene ◽  
Pseudo Second Order

In this paper, we present a recent study in the adsorption of uranium from an aquatic environment by reduced graphene oxide - Cu0.5Ni0.5Fe2O4 ferrite – polyaniline (RGO/CNF/PANI) composite. Uranium concentration was carried out by batch techniques. The effect of pH, contact time, concentration of equilibrium state and reusability on uranium adsorption capacity have been studied. The adsorption process was accomplished within 240 min and could be well described by the pseudo-second-order model. The adsorption isotherm agrees well with the Langmuir model, having a maximum adsorption capacity of 2000 mg/g, at pH = 5 and 25 oC. The RGO/CNF/PANI materials could be a promising absorbent for removing U (VI) in aqueous solution because of their high adsorption capacity and convenient magnetic separation. 

scholarly journals Equilibrium and Kinetic Study of Lead and Copper Ion Adsorption on Chitosan-Grafted-Polyacrylic Acid Synthesized by Surface Initiated Atomic Transfer Polymerization

Molecules ◽  
2018 ◽  
Vol 23 (9) ◽  
pp. 2218 ◽  
Author(s):  
Carlos Grande-Tovar ◽  
William Vallejo ◽  
Fabio Zuluaga
Keyword(s):  
Adsorption Capacity ◽  
Polyacrylic Acid ◽  
Adsorption Process ◽  
Kinetic Constant ◽  
Copper Ion ◽  
Toxic Metal ◽  
Maximum Adsorption Capacity ◽  
Order Model ◽  
Equilibrium Studies ◽  
Pseudo Second Order

In this work, we synthesized chitosan grafted-polyacrylic acid (CS-g-PA) through surface-initiated atom transfer radical polymerization (SI-ATRP). We also studied the adsorption process of copper and lead ions onto the CS-g-PA surface. Adsorption equilibrium studies indicated that pH 4.0 was the best pH for the adsorption process and the maximum adsorption capacity over CS-g-PA for Pb2+ ions was 98 mg·g−1 and for Cu2+ it was 164 mg·g−1, while for chitosan alone (CS), the Pb2+ adsorption capacity was only 14.8 mg·g−1 and for Cu2+ it was 140 mg·g−1. Furthermore, the adsorption studies indicated that Langmuir model describes all the experimental data and besides, pseudo-second-order model was suitable to describe kinetic results for the adsorption process, demonstrating a larger kinetic constant of the process was larger for Pb2+ than Cu2+. Compared to other adsorbents reported, CS-g-PA had comparable or even superior adsorbent capacity and besides, all these results suggest that the new CS-g-PA polymers had potential as an adsorbent for hazardous and toxic metal ions produced by different industries.

scholarly journals Synthesis Fe3O4/Talc nanocomposite by coprecipition-ultrasonication method and advances in hexavalent chromium removal from aqueous solution

2020 ◽  
Vol 38 (9-10) ◽  
pp. 483-501
Author(s):  
Nguyen Thi Huong ◽  
Nguyen Ngoc Son ◽  
Vo Hoang Phuong ◽  
Cong Tien Dung ◽  
Pham Thi Mai Huong ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Low Cost ◽  
Batch Experiments ◽  
X Ray Diffraction ◽  
Order Model ◽  
X Ray ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Langmuir And Freundlich Equations

The Fe3O4/Talc nanocomposite was synthesized by the coprecipitation-ultrasonication method. The reaction was carried out under a inert gas environment. The nanoparticles were characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), fourier-transform infrared spectroscopy (FT-IR) and vibrating sample magnetometry techniques (VSM), the surface area of the nanoparticles was determined to be 77.92 m2/g by Brunauer-Emmett-Teller method (BET). The kinetic data showed that the adsorption process fitted with the pseudo-second order model. Batch experiments were carried out to determine the adsorption kinetics and mechanisms of Cr(VI) by Fe3O4/Talc nanocomposite. The adsorption process was found to be highly pH-dependent, which made the material selectively adsorb these metals from aqueous solution. The isotherms of adsorption were also studied using Langmuir and Freundlich equations in linear forms. It is found that the Langmuir equation showed better linear correlation with the experimental data than the Freundlich. The thermodynamics of Cr(VI) adsorption onto the Fe3O4/Talc nanocomposite indicated that the adsorption was exothermic. The reusability study has proven that Fe3O4/Talc nanocomposite can be employed as a low-cost and easy to separate.

scholarly journals Removal of Crystal Violet Dye from Aqueous Solutions onto Date Palm Fiber by Adsorption Technique

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Mashael Alshabanat ◽  
Ghadah Alsenani ◽  
Rasmiah Almufarij
Keyword(s):  
Crystal Violet ◽  
Date Palm ◽  
Dye Removal ◽  
Adsorption Process ◽  
Maximum Adsorption Capacity ◽  
Order Model ◽  
Date Palm Fibers ◽  
Crystal Violet Dye ◽  
Pseudo Second Order ◽  
Influence Of Ph

The adsorption of crystal violet (CV) onto date palm fibers (DPFs) was examined in aqueous solution at 25°C. The experimental maximum adsorption capacity value was0.66×10−6. Langmuir, Freundlich, Elovich and Temkin models were applied to describe the equilibrium isotherms. The influence of pH and temperature on dye removal was evaluated. The percentage removal of CV dye by adsorption onto DPF at different pH and temperatures showed that these factors play a role in the adsorption process. Thermodynamic analysis was performed, and the Gibbs free energyΔGο, enthalpy changeΔHο, and entropyΔSοwere calculated. The negative values ofΔGοindicate spontaneous adsorption. The negative value ofΔHοindicates that the interaction between CV and DPF is exothermic, and the positive value ofΔSοindicates good affinity between DPF and CV. The kinetic data were fitted to a pseudo-second-order model.

Facile synthesis of chitosan nanoparticle-modified MnO2 nanoflakes for ultrafast adsorption of Pb(II) from aqueous solution

2016 ◽  
Vol 17 (1) ◽  
pp. 32-38 ◽  
Author(s):  
Tianli Han ◽  
Xiaoman Zhang ◽  
Xiangqian Fu ◽  
Jinyun Liu
Keyword(s):  
Aqueous Solution ◽  
Ph Value ◽  
Langmuir Model ◽  
Maximum Adsorption Capacity ◽  
Order Model ◽  
Facile Synthesis ◽  
Adsorption Sites ◽  
Chitosan Nanoparticle ◽  
Pseudo Second Order ◽  
Potential Strategy

Chitosan nanoparticle (CS NP)-modified MnO2 nanoflakes were presented as a novel adsorbent for fast adsorption of Pb(II) from aqueous solution. Loading dense CS NPs onto mono-dispersive flower-like MnO2 nanostructures reduces the overlap of CS during adsorption, and thus improves the contact of functional adsorption sites on the surface of MnO2 nanoflakes with heavy metal ions. The results show that the removal efficiency of the nanoadsorbents reaches up to 93% in 3 min for Pb(II). In addition, the maximum adsorption capacity, effects of adsorbent dosage and pH value, and the reusability were investigated. The kinetic process and adsorption isotherm fit well with the pseudo-second-order model and Langmuir model, respectively. These findings provide a potential strategy to address the overlap issue of some common nanoadsorbents.

scholarly journals REMOVAL OF Pb2+ FROM AQUEOUS SOLUTION BY ADSORPTION ONTO COMPOSITE BASED ON EUCALYPTUS LEAF AND POLYANILINE

2017 ◽  
Vol 55 (1) ◽  
pp. 54
Author(s):  
Le Cao The ◽  
Vu Minh Tan ◽  
Phan Thi Binh
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Sem Images ◽  
Adsorption Data ◽  
Freundlich Adsorption Isotherm ◽  
Pseudo Second Order ◽  
Ir Analysis ◽  
Polymerization Method

Composite based on eucalyptus leaf and polyaniline (EL-PANi) was prepared by chemical polymerization method. It showed that the function groups belonging to polyaniline and eucalyptus leaf were found through IR analysis and the nanostructure of composite was explained by SEM images. The adsorption of  Pb2+ was carried out onto composite in aqueous solution via varying pH, contact time, and its initial concentration. The experimental adsorption data fitted well into Freundlich adsorption isotherm model (r2 = 0.9873). The adsorption process followed pseudo-second order kinetic with r2 = 0.9995. The maximum adsorption capacity of Pb2+ onto that composite was 172.4138 mg/g  by Langmuir equation and KF was 58.7527 mg/g by Freundlich one.

Sign in / Sign up

Export Citation Format

Share Document