scholarly journals Soft Denture Liner Adhesion to Conventional and CAD/CAM Processed Poly(Methyl Methacrylate) Acrylic Denture Resins-An In-Vitro Study

Materials ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 6614
Author(s):  
Sara Mohammad Al Taweel ◽  
Hanan Nejer Al-Otaibi ◽  
Nawaf Labban ◽  
Afnan AlFouzan ◽  
Huda Al Shehri
Keyword(s):  
Bond Strength ◽  
Methyl Methacrylate ◽  
Surface Treatment ◽  
Failure Modes ◽  
Airborne Particle ◽  
Poly Methyl Methacrylate ◽  
Acrylic Resins ◽  
Significant Difference ◽  
Cad Cam ◽  
Denture Liners

This study aimed to evaluate the airborne-particle abrasion surface treatment effects on the tensile bond strength (TBS) between resilient denture liner and CAD/CAM or conventional heat polymerized poly (methyl methacrylate) (PMMA) acrylic denture resins. A total of 48 dumbbell-shaped specimens (70 mm in total length, and 12 mm and 7 mm in diameter at the thickest and thinnest section, respectively) were prepared from CAD/CAM and conventional acrylic resins. Before relining with denture liner, 12 specimens from each material were surface-treated by 110 µm Al2O3 airborne-particle abrasion, and the remaining specimens served as control (no treatment). Following relining, all the specimens were aged by thermal cycling (1000 cycles, 5–55 °C). The TBS of denture liner to acrylic denture resins was tested in a universal testing apparatus at a 5 mm/min crosshead speed. The debonded surfaces were visually examined for the failure modes. ANOVA and multiple comparisons posthoc analysis tests were applied to determine the significant difference in TBS between the study groups (α = 0.05). A significant difference in TBS was observed between the control and surface treated groups (p < 0.001) for both acrylic resins materials. However, there was no statistically significant difference in bond strength between the acrylic resins materials (p = 0.739). Surface treatment with airborne-particle abrasion demonstrated increased TBS of the soft denture liners to acrylic resins. The TBS of conventional and CAD/CAM acrylic resins to soft denture liners were not considerably different.

The Effect of Thickness on the Fracture Strength and Failure Modes of Zirconia Crowns

2016 ◽  
Vol 697 ◽  
pp. 629-632
Author(s):  
Li Xian Zhang ◽  
Rui Li ◽  
Yu Niu ◽  
Yu Xiao Liu
Keyword(s):  
Fracture Strength ◽  
Failure Modes ◽  
Statistical Significance ◽  
Dental Practice ◽  
Significant Difference ◽  
Cad Cam ◽  
Zirconia Crowns ◽  
Different Thickness

To explore the effect of thickness on the fracture strength and failure modes of zirconia crowns, four crown models with different thickness (1.2 mm, 1.0 mm, 0.8 mm, 0.6 mm) with the same shape were designed by Dental Designer software in CAD/CAM system. They were manufactured to 40 zirconia crowns by CAM carving machine. The fracture strength and the failure modes of each crown was measured, while porcelain fused to metal (PFM) crowns as control. The average fracture strength of different zirconia crowns were recorded as below: 1308.38 ± 111.38 N (Group 0.6 mm), 1841.60 ± 68.21 N (Group 0.8 mm), 2429.88 ± 315.03 N (Group 1.0 mm), 3068.31 ± 233.88 N (Group 1.2 mm). There was no significant difference between Group 1.0 mm and Group 1.2 mm (P > 0.05), and statistical significance was obtained among every other two groups (P < 0.05). The failure modes of different thickness zirconium crowns are similar. There are more broken pieces from thicker crowns compared to thinner ones. It is concluded that the thickness can influence the fracture strength of zirconia crown. With the increase of the thickness, the fracture strength of the zirconium crowns also increases. We recommend zirconia crowns thicker than or at least 1.0 mm in dental practice.

scholarly journals Effect of Surface Treatments on the Bond Strength to Turkom-Cera All-ceramic Material

2016 ◽  
Vol 17 (11) ◽  
pp. 920-925 ◽  
Author(s):  
Bandar MA Al-Makramani ◽  
Fuad A Al-Sanabani ◽  
Abdul AA Razak ◽  
Mohamed I Abu-Hassan ◽  
Ibrahim Z AL-Shami ◽  
...  
Keyword(s):  
Bond Strength ◽  
Ceramic Material ◽  
Failure Modes ◽  
Testing Machine ◽  
Surface Treatments ◽  
Resin Cement ◽  
Control Group ◽  
Significant Difference ◽  
All Ceramic ◽  
Effect Of Surface

ABSTRACT Aim The aim of this study was to evaluate the effect of surface treatments on shear bond strength (SBS) of Turkom-Cera (Turkom-Ceramic (M) Sdn. Bhd., Puchong, Malaysia) all-ceramic material cemented with resin cement Panavia-F (Kuraray Medical Inc., Okayama, Japan). Materials and methods Forty Turkom-Cera ceramic disks (10 mm × 3 mm) were prepared and randomly divided into four groups. The disks were wet ground to 1000-grit and subjected to four surface treatments: (1) No treatment (Control), (2) sandblasting, (3) silane application, and (4) sandblasting + silane. The four groups of 10 specimens each were bonded with Panavia-F resin cement according to manufacturer's recommendations. The SBS was determined using the universal testing machine (Instron) at 0.5 mm/min crosshead speed. Failure modes were recorded and a qualitative micromorphologic examination of different surface treatments was performed. The data were analyzed using the one-way analysis of variance (ANOVA) and Tukey honestly significant difference (HSD) tests. Results The SBS of the control, sandblasting, silane, and sandblasting + silane groups were: 10.8 ± 1.5, 16.4 ± 3.4, 16.2 ± 2.5, and 19.1 ± 2.4 MPa respectively. According to the Tukey HSD test, only the mean SBS of the control group was significantly different from the other three groups. There was no significant difference between sandblasting, silane, and sandblasting + silane groups. Conclusion In this study, the three surface treatments used improved the bond strength of resin cement to Turkom-Cera disks. Clinical significance The surface treatments used in this study appeared to be suitable methods for the cementation of glass infiltrated all-ceramic restorations. How to cite this article Razak AAA, Abu-Hassan MI, AL-Makramani BMA, AL-Sanabani FA, AL-Shami IZ, Almansour HM. Effect of Surface Treatments on the Bond Strength to Turkom-Cera All-Ceramic Material. J Contemp Dent Pract 2016;17(11):920-925.

scholarly journals Effects of Immediate and Delayed Cementations for CAD/CAM Resin Block after Alumina Air Abrasion on Adhesion to Newly Developed Resin Cement

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 7058
Author(s):  
Akane Chin ◽  
Masaomi Ikeda ◽  
Tomohiro Takagaki ◽  
Toru Nikaido ◽  
Alireza Sadr ◽  
...  
Keyword(s):  
Bond Strength ◽  
Water Sorption ◽  
Resin Composite ◽  
Resin Cement ◽  
Air Abrasion ◽  
Resin Cements ◽  
Significant Difference ◽  
Computer Aided ◽  
Cad Cam ◽  
Curing Methods

The purpose of this study was to evaluate the effect of one week of Computer-aided design/Computer-aided manufacturing (CAD/CAM) crown storage on the μTBS between resin cement and CAD/CAM resin composite blocks. The micro-tensile bond strength (μTBS) test groups were divided into 4 conditions. There are two types of CAD/CAM resin composite blocks, namely A block and P block (KATANA Avencia Block and KATANA Avencia P Block, Kuraray Noritake Dental, Tokyo, Japan) and two types of resin cements. Additionally, there are two curing methods (light cure and chemical cure) prior to the μTBS test—Immediate: cementation was performed immediately; Delay: cementation was conducted after one week of storage in air under laboratory conditions. The effect of Immediate and Delayed cementations were evaluated by a μTBS test, surface roughness measurements, light intensity measurements, water sorption measurements and Scanning electron microscope/Energy dispersive X-ray spectrometry (SEM/EDS) analysis. From the results of the μTBS test, we found that Delayed cementation showed significantly lower bond strength than that of Immediate cementation for both resin cements and both curing methods using A block. There was no significant difference between the two types of resin cements or two curing methods. Furthermore, water sorption of A block was significantly higher than that of P block. Within the limitations of this study, alumina air abrasion of CAD/CAM resin composite restorations should be performed immediately before bonding at the chairside to minimize the effect of humidity on bonding.

scholarly journals Impact of Intracoronal Dentin Treatment Prior to Bleaching on Bond Strength of Restorative Materials

2014 ◽  
Vol 25 (6) ◽  
pp. 519-523 ◽  
Author(s):  
Erica Moreno Zanconato-Carvalho ◽  
João Felipe Bruniera ◽  
Natália Spadini de Faria ◽  
Vivian Colucci ◽  
Danielle Cristine Messias
Keyword(s):  
Phosphoric Acid ◽  
Bond Strength ◽  
Surface Treatment ◽  
Shear Bond Strength ◽  
Composite Resin ◽  
Er:Yag Laser ◽  
Composite Resins ◽  
Bleaching Procedure ◽  
Significant Difference ◽  
Restorative Materials

Surface treatment of dentin before the bleaching procedure may affect its permeability and influence the bond strength of restorative materials. This study evaluated the influence of surface treatment before the bleaching on shear bond strength (SBT) of restorative materials to intracoronal dentin. Dentin slabs were subjected to surface treatment: no bleaching (control - CON), no surface treatment + bleaching (HP), 37% phosphoric acid + bleaching (PA) and Er:YAG laser + bleaching (L). After the bleaching procedure, specimens (n=10) were restored with: microhybrid composite resin (MH), flowable composite resin (F), and resin-modified glass-ionomer cement (RMGIC). The shear test was carried out. ANOVA and Tukey's test (α=0.05) showed significant difference for surface treatment and restorative materials (p<0.05). CON presented higher STB and was statistically different from HP (p<0.05). PA and L showed intermediate values and were statistically similar to CON and HP (p>0.05). STB for MH and F were higher than RMGIC (p<0.05), and did not differ from each other (p>0.05). The surface treatments with phosphoric acid and Er:YAG laser before the bleaching procedure provided shear bond strength at the same level of unbleached dentin and the composite resins presented superior bond strength to the intracoronal dentin.

scholarly journals Assessment the Bond Strength of Ceramic Brackets to CAD/CAM Nanoceramic Composite and Interpenetrating Network Composite after Different Surface Treatments

2018 ◽  
Vol 2018 ◽  
pp. 1-6 ◽  
Author(s):  
Mustafa Mehmet Özarslan ◽  
Özlem Üstün ◽  
Ulviye Sebnem Buyukkaplan ◽  
Çağatay Barutcigil ◽  
Nurullah Türker ◽  
...  
Keyword(s):  
Bond Strength ◽  
Surface Treatment ◽  
Hydrofluoric Acid ◽  
Shear Bond Strength ◽  
Surface Treatments ◽  
Interpenetrating Network ◽  
Bonding Performance ◽  
Cad Cam ◽  
Ceramic Brackets ◽  
New Generation

Adult orthodontics may confront problems related to the bonding performance of orthodontic brackets to new generation restorative materials used for crown or laminate restorations. The aim of the present study was to investigate the shear bond strength of ceramic brackets to two new generation CAD/CAM interpenetrating network composite and nanoceramic composite after different surface treatments. Er,Cr:YSGG Laser, hydrofluoric acid (9%), sandblasting (50 μm Al2O3), and silane were applied to the surfaces of 120 CAD/CAM specimens with 2 mm thickness and then ceramic brackets were bonded to the treated surfaces of the specimens. Bond strength was evaluated using the shear bond strength test. According to the results, CAD/CAM block types and surface treatment methods have significant effects on shear bond strength. The lowest bond strength values were found in the specimens treated with silane (3.35 ± 2.09 MPa) and highest values were found in the specimens treated with sandblast (8.92 ± 2.77 MPa). Sandblasting and hydrofluoric acid surface treatment led to the most durable bonds for the two types of CAD/CAM blocks in the present study. In conclusion, different surface treatments affect the shear bond strength of ceramic brackets to CAD/CAM interpenetrating network composite and nanoceramic composite. Among the evaluated treatments, sandblasting and hydrofluoric acid application resulted in sufficient bonding strength to ceramic brackets for both of the CAD/CAM materials.

scholarly journals Effect of Glass Fiber Post Adaptation on Push-Out Bond Strength to Root Dentin

2019 ◽  
Vol 30 (4) ◽  
pp. 350-355 ◽  
Author(s):  
Thiago Lopes de Freitas ◽  
Rafael Pino Vitti ◽  
Milton Edson Miranda ◽  
William Cunha Brandt
Keyword(s):  
Bond Strength ◽  
Glass Fiber ◽  
Root Canal ◽  
Failure Modes ◽  
Resin Cement ◽  
Adhesive Failure ◽  
Fiber Post ◽  
Significant Difference ◽  
Glass Fiber Post ◽  
Push Out

Abstract The aim of this study was to evaluate the effect of different glass fiber posts (GFPs) diameters on the push-out bond strength to dentin. Forty unirradicular human teeth were endodontically treated and used for cementation of GFPs (White Post DC, FGM) with different diameters (n=10): P1 - ø 1.6 mm coronal x 0.85 mm apical; P2 - ø 1.8 mm coronal x 1.05 mm apical; P5 - ø 1.4 mm coronal x 0.65 mm apical; and PC - customized post number 0.5 with composite resin (Tetric Ceram A2, Ivoclair Vivadent). All GFPs were cemented into the root canal using a dual-curing luting composite (Variolink II, Ivoclar Vivadent). One slice (1.7 mm) of each root third of cemented GFP (cervical, middle, and apical) was submitted to push-out testing. Failure modes of all specimens were classified as: adhesive failure between resin cement and post; adhesive failure between dentin and resin cement; cohesive failure within resin cement, post or dentin; and mixed failure. The data were analyzed with two-way ANOVA and Tukey’s test (a=0.05). The highest bond strength values were presented for the P2 and PC groups. There was no statistically significant difference between the GFP thirds in each group. The groups P2, P5, and PC showed predominantly adhesive failure. For P1, the most prevalent type of failure was adhesive between resin cement and post. It may be concluded that a glass fiber post that is well adapted to the root canal presents higher bond strength values, regardless of GFP third.

Sign in / Sign up

Export Citation Format

Share Document