scholarly journals Hybrid Electron Beam Powder Bed Fusion Additive Manufacturing of Ti–6Al–4V: Processing, Microstructure, and Mechanical Properties

2022 ◽  
Author(s):  
R. Tosi ◽  
E. Muzangaza ◽  
X. P. Tan ◽  
D. Wimpenny ◽  
M. M. Attallah
Keyword(s):  
Mechanical Properties ◽  
Electron Beam ◽  
Additive Manufacturing ◽  
Powder Bed Fusion ◽  
Powder Bed ◽  
Bonding Performance ◽  
Microstructure And Mechanical Properties ◽  
Basic Understanding ◽  
Hybrid Concept ◽  
Integrated Or

AbstractProcessing, microstructure, and mechanical properties of the hybrid electron beam powder bed fusion (E-PBF) additive manufacturing of Ti–6Al–4V have been investigated. We explore the possibility of integrating the substrate as a part of the final component as a repair, integrated, or consolidated part. Various starting plate surface conditions are used to understand the joining behavior and their microstructural properties in the bonding region between the plate and initial deposited layers. It is found that mechanical failures mainly occur within the substrate region due to the dominant plastic strains localized in the weaker Ti–6Al–4V substrate. The hybrid concept is successfully proven with satisfactory bonding performance between the E-PBF build and substrate. This investigation improves the practice of using the hybrid E-PBF additive manufacturing technique and provides basic understanding to this approach.

scholarly journals On the Impact of Build Envelope Sizes on E-PBF Processed Pure Iron

2021 ◽  
Author(s):  
C. J. J. Torrent ◽  
P. Krooß ◽  
T. Niendorf
Keyword(s):  
Mechanical Properties ◽  
Electron Beam ◽  
Additive Manufacturing ◽  
Thermal History ◽  
Powder Bed Fusion ◽  
Parameter Setting ◽  
Powder Bed ◽  
History Of ◽  
Specific Temperature ◽  
The Impact

AbstractIn additive manufacturing, the thermal history of a part determines its final microstructural and mechanical properties. The factors leading to a specific temperature profile are diverse. For the integrity of a parameter setting established, periphery variations must also be considered. In the present study, iron was processed by electron beam powder bed fusion. Parts realized by two process runs featuring different build plate sizes were analyzed. It is shown that the process temperature differs significantly, eventually affecting the properties of the processed parts.

scholarly journals Quasi-Static Tensile Properties of Unalloyed Copper Produced by Electron Beam Powder Bed Fusion Additive Manufacturing

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2932
Author(s):  
Prithwish Tarafder ◽  
Christopher Rock ◽  
Timothy Horn
Keyword(s):  
Mechanical Properties ◽  
Electron Beam ◽  
Additive Manufacturing ◽  
Tensile Test ◽  
Vacuum Annealing ◽  
Grain Morphology ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Powder Bed Fusion ◽  
Powder Bed

Mechanical properties of powder bed fusion processed unalloyed copper are reported majorly in the as-fabricated condition, and the effect of post-processes, common to additive manufacturing, is not well documented. In this study, mechanical properties of unalloyed copper processed by electron beam powder bed fusion are characterized via room temperature quasi-static uniaxial tensile test and Vickers microhardness. Tensile samples were extracted both perpendicular and parallel to the build direction and assigned to three different conditions: as-fabricated, hot isostatic pressing (HIP), and vacuum annealing. In the as-fabricated condition, the highest UTS and lowest elongation were obtained in the samples oriented perpendicular to the build direction. These were observed to have clear trends between sample orientation caused primarily by the interdependencies between the epitaxial columnar grain morphology and dislocation movement during the tensile test. Texture was insignificant in the as-fabricated condition, and its effect on the mechanical properties was outweighed by the orientation anisotropy. The fractographs revealed a ductile mode of failure with varying dimple sizes where more shallow and finely spaced dimples were observed in the samples oriented perpendicular to the build direction. EDS maps reveal that grain boundary oxides coalesce and grow in HIP and vacuum-annealed specimens which are seen inside the ductile dimples and contribute to their increased ductility. Overall, for the post-process parameters chosen in this study, HIP was observed to slightly increase the sample’s density while vacuum annealing reduced the oxygen content in the specimens.

scholarly journals Influence of Microstructure and Defects on Mechanical Properties of AISI H13 Manufactured by Electron Beam Powder Bed Fusion

2021 ◽  
Author(s):  
Moritz Kahlert ◽  
Florian Brenne ◽  
Malte Vollmer ◽  
Thomas Niendorf
Keyword(s):  
Mechanical Properties ◽  
Electron Beam ◽  
Additive Manufacturing ◽  
Internal Cooling ◽  
Layer By Layer ◽  
Powder Bed Fusion ◽  
Powder Bed ◽  
Cooling Channels ◽  
Fine Grained ◽  
Aisi H13

AbstractElectron beam powder bed fusion (E-PBF) is a well-known additive manufacturing process. Components are realized based on layer-by-layer melting of metal powder. Due to the high degree of design freedom, additive manufacturing came into focus of tooling industry, especially for tools with sophisticated internal cooling channels. The present work focuses on the relationships between processing, microstructure evolution, chemical composition and mechanical properties of a high alloyed tool steel AISI H13 (1.2344, X40CrMoV5-1) processed by E-PBF. The specimens are free of cracks, however, lack of fusion defects are found upon use of non-optimized parameters finally affecting the mechanical properties detrimentally. Specimens built based on suitable parameters show a relatively fine grained bainitic/martensitic microstructure, finally resulting in a high ultimate strength and an even slightly higher failure strain compared to conventionally processed and heat treated AISI H13.

Sign in / Sign up

Export Citation Format

Share Document