Temperature-Dependent Wear Characteristics of a High-Voltage Low-Current Electric Energy-Treated AISI 1080 Steel

Author(s):  
Mousumi Mallick ◽  
Biplab Hazra ◽  
Swapan Kumar Mitra ◽  
Debasish Basak ◽  
Bijay Kumar Show ◽  
...  
Molecules ◽  
2020 ◽  
Vol 25 (8) ◽  
pp. 1928
Author(s):  
Gilyong Shin ◽  
Jei Gyeong Jeon ◽  
Ju Hyeon Kim ◽  
Ju Hwan Lee ◽  
Hyeong Jun Kim ◽  
...  

The photovoltaic conversion efficiency of solar cells is highly temperature dependent and decreases with increasing temperature. Therefore, the thermal management of solar cells is crucial for the efficient utilization of solar energy. We fabricate a hybrid photovoltaic/thermocell (PV/T) module by integrating a thermocell directly into the back of a solar panel and explore the feasibility of the module for its practical implementation. The proposed PV/T hybrid not only performs the cooling of the solar cells but also produces an additional power output by converting the heat stored in the solar cell into useful electric energy through the thermocell. Under illumination with an air mass of 1.5 G, the conversion efficiency of the solar cell can improve from 13.2% to 15% by cooling the solar cell from 61 °C to 34 °C and simultaneously obtaining an additional power of 3.53 μW/cm2 from the thermocell. The advantages of the PV/T module presented in this work, such as the additional power generation from the thermocell as well as the simultaneous cooling of the solar cells and its convenient installation, can lead to the module’s importance in practical and large-scale deployment.


2015 ◽  
Vol 111 ◽  
pp. 12-17 ◽  
Author(s):  
Andrzej Taube ◽  
Jakub Kaczmarski ◽  
Renata Kruszka ◽  
Jakub Grochowski ◽  
Kamil Kosiel ◽  
...  

2017 ◽  
Vol 2017 ◽  
pp. 1-9 ◽  
Author(s):  
A. Cavallo ◽  
G. Canciello ◽  
B. Guida

In this paper an issue related to electric energy management on board an aircraft is considered. A battery pack is connected to a high-voltage bus through a controlled Battery Charge/Discharge Unit (BCDU) that makes the overall behaviour of the battery “intelligent.” Specifically, when the aeronautic generator feeding the high-voltage bus has enough energy the battery is kept under charge, while if more loads are connected to the bus, so that the overload capacity of the generator is exceeded, the battery “helps” the generator by releasing its stored energy. The core of the application is a robust, supervised control strategy for the BCDU that automatically reverts the flow of power in the battery, when needed. Robustness is guaranteed by a low-level high gain control strategy. Switching from full-charge mode (i.e., when the battery absorbs power from the generator) to generator mode (i.e., when the battery pumps energy on the high-voltage bus) is imposed by a high-level supervisor. Different from previous approaches, mathematical proofs of stability are given for the controlled system. A switching implementation using a finite-time convergent controller is also proposed. The effectiveness of the proposed strategy is shown by detailed simulations in Matlab/Stateflow/SimPowerSystem.


2013 ◽  
Vol 341-342 ◽  
pp. 1245-1249 ◽  
Author(s):  
Zhi Shou Zheng ◽  
Li Xin Wang ◽  
Xi Wu Chen ◽  
Wen Dong Deng ◽  
Jia Hai Zhang ◽  
...  

A novel apparatus is introduced in this paper used to measure high voltage electric energy based on three-phase four-wire virtual-ground theory. The virtual-ground design, Faraday shielding technique and Warner DC (Direct Current) self-supply method are integrated in this apparatus based on new I/V, V/V techniques to realize high accuracy, reliability and wide-linear range measuring. The effectiveness of the apparatus has been proved by in-house calibration and on-site test . The test result shows that it can be used in high voltage grid on-site calibration . Its measurement uncertainty can be limited to 0.1% under the condition of PF=1.0~0.8, and can reach 0.15% as PF=0.5. In summary, the apparatus discussed in this paper can be applied as high voltage electric energy measurement instrument to meet the requirement of online metrological verification and calibration. Furthermore, it is very useful for building the system of Advanced Metering Infrastructure (AMI) in smart grid.


Sign in / Sign up

Export Citation Format

Share Document