scholarly journals Performance of integrated sequencing batch reactor (SBR) and reverse osmosis (RO) process for leachate treatment: effect of pH

2022 ◽  
Author(s):  
Izabela Anna Tałałaj
Keyword(s):  
Organic Matter ◽  
Reverse Osmosis ◽  
Membrane Fouling ◽  
Removal Rate ◽  
Membrane Surface ◽  
Ammonia Nitrogen ◽  
Electrostatic Repulsion ◽  
Permeate Flux ◽  
Leachate Treatment ◽  
Good Efficiency

Abstract Purpose In this paper the performance and effectiveness of the reverse osmosis (RO) process for the biologically pretreated leachate was investigated. The RO process was carried out separately for two different pH: 8.0 and 9.3. Methods A general pollution parameters as well as organic and inorganic indicators were determined in raw, biologically pretreated and RO treated leachate. The performance characteristics of the reverse osmosis system were made on the basis of permeate flux, electroconductivity removal rate, concentration factor and efficiency in removal of analyzed parameters. Results The use of SBR pretreatment had very good efficiency in BOD (97.3%) and ammonia nitrogen (95.4%) removal. The lowest effectivity was observed for chloride (11.6%), boron (3.9%) and TDS (1.2%). Pretreated leachate was subjected to RO system. The normalized average flux was 0.53 (42.3 L/m2·h) for pH = 8.0 and 0.68 (33.5 L/m2·h) for pH = 9.3. The lower membrane fouling at higher pH can be explained by electrostatic repulsion between the negatively charged membrane surface and organic substances. Independently of the process pH, a two-step membrane fouling was observed. The greatest differences in removal rates were observed for boron, which had a higher retention rate at higher pH, and ammonia nitrogen, whose removal rate decreased at higher pH. The obtained permeate pH after RO process was lower than the feed pH in two analyzed value of pH. Conclusions The higher flux value at pH = 9.3 is result of high content of organic matter in leachate, which is better rejected at higher pH because of higher electrostatic repulsion between organic matter and membrane surface. This indicates that the organic matter content should be taken into account when determining the operating parameters (pH values) of the RO system.

Comparison of reverse osmosis membrane fouling characteristics in full-scale leachate treatment systems with chemical coagulation and microfiltration pre-treatments

2014 ◽  
Vol 71 (4) ◽  
pp. 580-587 ◽  
Author(s):  
Weerapong Rukapan ◽  
Benyapa Khananthai ◽  
Thirdpong Srisukphun ◽  
Wilai Chiemchaisri ◽  
Chart Chiemchaisri
Keyword(s):  
Reverse Osmosis ◽  
Membrane Fouling ◽  
Full Scale ◽  
Permeate Flux ◽  
Leachate Treatment ◽  
Chemical Coagulation ◽  
Cake Layer ◽  
Ro Membrane ◽  
Pre Treatment ◽  
Fouling Characteristics

Fouling characteristics of reverse osmosis (RO) membrane with chemical coagulation and microfiltration (MF) pre-treatment were investigated at full-scale leachate treatment systems. In chemical coagulation pre-treatment, solid separation from stabilized leachate was performed by ferric chloride coagulation followed by sand filtration. Meanwhile, MF pre-treatment and the RO system utilized direct filtration using a 0.03 µm membrane without chemical addition. MF pre-treatment yielded better pollutant removals in terms of organics and nitrogen. The study on effect of pre-treatment on RO membrane fouling revealed that accumulated foulant on the RO membrane in MF pre-treatment was significantly lower than that of chemical coagulation. Nevertheless, NaOH cleaning of the fouled RO membrane after chemical coagulation pre-treatment could better recover its permeate flux, thus suggesting that the formation of a loose-structure cake layer by chemical coagulation pre-treatment could allow effective penetration of chemical cleaning and detachment of foulant layer from the membrane surface.

scholarly journals Membrane cleaning in membrane distillation of reverse osmosis concentrate generated in landfill leachate treatment

2021 ◽  
Author(s):  
Xiaolin Jia ◽  
Kuiling Li ◽  
Baoqiang Wang ◽  
ZhiChao Zhao ◽  
Deyin Hou ◽  
...  
Keyword(s):  
Reverse Osmosis ◽  
Landfill Leachate ◽  
Membrane Fouling ◽  
Membrane Distillation ◽  
Water Recovery ◽  
Permeate Flux ◽  
Chemical Cleaning ◽  
Leachate Treatment ◽  
Membrane Cleaning ◽  
Cleaning Methods

Abstract As a thermally induced membrane separation process, membrane distillation (MD) has drawn more and more attention for the advantages of treating hypersaline wastewaters, especially the concentrate from reverse osmosis (RO) process. One of the major obstacles in widespread MD application is the membrane fouling. We investigated the feasibility of direct contact membrane distillation (DCMD) for landfill leachate reverse osmosis concentrate (LFLRO) brine treatment and systematically assessed the efficiency of chemical cleaning for DCMD after processing LFLRO brine. The results showed that 80% water recovery rate was achieved when processing the LFLRO brine by DCMD, but the membrane fouling occurred during the DCMD process, and manifested as the decreasing of permeate flux and the increasing of permeate conductivity. Analysis revealed that the serious flux reduction was primarily caused by the fouling layer that consist of organic matters and inorganic salts. Five cleaning methods were investigated for membrane cleaning, including hydrogen chloride (HCl)-sodium hydroxide (NaOH), ethylene diamine tetraacetic acid (EDTA)-NaOH, critic acid, sodium hypochlorite (NaClO) and sodium dodecyl sulphate (SDS) cleaning. Among the chemical cleaning methods investigated, the 3 wt.% SDS cleaning showed the best efficiency at recovering the performance of fouled membranes.

scholarly journals Effect of heat treatment on fouling resistance and the rejection of small and neutral solutes by reverse osmosis membranes

2014 ◽  
Vol 15 (3) ◽  
pp. 510-516 ◽  
Author(s):  
Takahiro Fujioka ◽  
Nagayasu Oshima ◽  
Ryoichi Suzuki ◽  
Michael Higgins ◽  
William E. Price ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Reverse Osmosis ◽  
Free Volume ◽  
Membrane Fouling ◽  
Volume Fraction ◽  
Membrane Surface ◽  
Feed Solution ◽  
Membrane Properties ◽  
Permeate Flux ◽  
Fouling Resistance

The effects of heat treatment on membrane fouling resistance and the rejection of small and neutral solutes by reverse osmosis (RO) membranes were elucidated. RO membrane modification by heat treatment reduced fouling and improved boron rejection. However, heat treatment also caused a decrease in the water permeability of RO membranes. Significant improvement on fouling resistance by heat treatment was observed when RO concentrate was used to simulate a feed solution with high fouling propensity. The improved fouling resistance is likely to be due to changes in the hydrophobic interaction between the membrane surface and foulants. Boron rejection by the ESPA2 membrane was enhanced by heat treatment from 26 to 68% (when evaluated at the permeate flux of 20 L/m2 h). Positron annihilation lifetime spectroscopy revealed that heat treatment did not significantly influence the free-volume hole-radius of the membrane active skin layer. The results reported in this study suggested that changes in the other membrane properties such as free-volume fraction and thickness may be the main cause improving boron rejection.

Coagulation/flocculation/ultrafiltration for natural organic matter removal in drinking water production

2004 ◽  
Vol 4 (5-6) ◽  
pp. 215-222 ◽  
Author(s):  
A.R. Costa ◽  
M.N. de Pinho
Keyword(s):  
Drinking Water ◽  
Organic Matter ◽  
Natural Organic Matter ◽  
Membrane Fouling ◽  
Membrane Filtration ◽  
Membrane Surface ◽  
Water Production ◽  
Cellulose Acetate Membranes ◽  
Wide Range ◽  
Drinking Water Production

Membrane fouling by natural organic matter (NOM), namely by humic substances (HS), is a major problem in water treatment for drinking water production using membrane processes. Membrane fouling is dependent on membrane morphology like pore size and on water characteristics namely NOM nature. This work addresses the evaluation of the efficiency of ultrafiltration (UF) and Coagulation/Flocculation/UF performance in terms of permeation fluxes and HS removal, of the water from Tagus River (Valada). The operation of coagulation with chitosan was evaluated as a pretreatment for minimization of membrane fouling. UF experiments were carried out in flat cells of 13.2×10−4 m2 of membrane surface area and at transmembrane pressures from 1 to 4 bar. Five cellulose acetate membranes were laboratory made to cover a wide range of molecular weight cut-off (MWCO): 2,300, 11,000, 28,000, 60,000 and 75,000 Da. Severe fouling is observed for the membranes with the highest cut-off. In the permeation experiments of raw water, coagulation prior to membrane filtration led to a significant improvement of the permeation performance of the membranes with the highest MWCO due to the particles and colloidal matter removal.

Electroflocculation as potential pretreatment in colloid ultrafiltration

2006 ◽  
Vol 6 (1) ◽  
pp. 69-78 ◽  
Author(s):  
T. Harif ◽  
M. Hai ◽  
A. Adin
Keyword(s):  
Membrane Fouling ◽  
Colloidal Suspension ◽  
Membrane Surface ◽  
Constant Current ◽  
Permeate Flux ◽  
Batch Mode ◽  
Membrane Behavior ◽  
Flux Decline ◽  
Stainless Steel Cathode ◽  
Marginal Improvement

Electroflocculation (EF) is a coagulation/flocculation process in which active coagulant species are generated in situ by electrolytic oxidation of an appropriate anode material. The effect of colloidal suspension pretreatment by EF on membrane fouling was measured by flux decline at constant pressure. An EF cell was operated in batch mode and comprised two flat sheet electrodes, an aluminium anode and stainless steel cathode, which were immersed in the treated suspension, and connected to an external DC power supply. The cell was run at constant current between 0.06–0.2A. The results show that pre-EF enhances the permeate flux at pH 5 and 6.5, but only marginal improvement is observed at pH 8. At all pH values cake formation on the membrane surface was observed. The differences in membrane behavior can be explained by conventional coagulation theory and transitions between aluminium mononuclear species which affect particle characteristics and consequently cake properties. At pH 6.5, where sweep floc mechanism dominates due to increased precipitation of aluminium hydroxide, increased flux rates were observed. It is evident that EF can serve as an efficient pretreatment to ultrafiltration of colloid particles.

Topology Optimization of Spacers for Maximizing Permeate Flux on Membrane Surface in Reverse Osmosis Channel

2011 ◽  
Author(s):  
Seungjae Oh ◽  
Semyung Wang ◽  
Minkyu Park ◽  
Joonha Kim
Keyword(s):  
Topology Optimization ◽  
Pressure Drop ◽  
Reverse Osmosis ◽  
Membrane Surface ◽  
Design Development ◽  
Permeate Flux ◽  
Membrane Channel ◽  
Initial Attempt ◽  
Membrane Surfaces ◽  
Ro Membrane

The objective of this study is to design spacers using fluid topology optimization in 2D crossflow Reverse Osmosis (RO) membrane channel to improve the performance of RO processes. This study is an initial attempt to apply topology optimization to designing spacers in RO membrane channel. The performance was evaluated by the quantity of permeate flux penetrating both upper and lower membrane surfaces. A coupled Navier-Stokes and Convection-Diffusion model was employed to calculate the permeate flux. To get reliable solutions, stabilization methods were employed with standard finite element method. The nine reference models which consist of the combination of circle, rectangular, triangle shape and zigzag, cavity, submerge configuration of spacers were simulated. Such models were compared with new model designed by topology optimization. The permeate flux at both membrane surfaces was determined as an objective function. In addition, permissible pressure drop along the channel and spacer volume were used as constraints. As a result of topology optimization as the permissible pressure drop changes in channel, characteristics of spacer design development was founded. Spacer design based on topology optimization was reconstructed to a simple one considering manufactuability and characteristics of development spacer design. When a simplified design was compared with previous 9 models, new design has a better performance in terms of permeate flux and wall concentration at membrane surface.

A Wall Film Model for Membrane Fouling

2018 ◽  
Author(s):  
Sina Jahangiri Mamouri ◽  
Volodymyr V. Tarabara ◽  
André Bénard
Keyword(s):  
Multiphase Flow ◽  
Membrane Fouling ◽  
Oil And Gas ◽  
Membrane Separation ◽  
Film Formation ◽  
Membrane Surface ◽  
Permeate Flux ◽  
Water Separation ◽  
Wall Film ◽  
Oil Water

Deoiling of produced or impaired waters associated with oil and gas production represents a significant challenge for many companies. Centrifugation, air flotation, and hydrocyclone separation are the current methods of oil removal from produced water [1], however the efficiency of these methods decreases dramatically for droplets smaller than approximately 15–20 μm. More effective separation of oil-water mixtures into water and oil phases has the potential to both decrease the environmental footprint of the oil and gas industry and improve human well-being in regions such as the Gulf of Mexico. New membrane separation processes and design of systems with advanced flow management offer tremendous potential for improving oil-water separation efficacy. However, fouling is a major challenge in membrane separation [2]. In this study, the behavior of oil droplets and their interaction with crossflow filtration (CFF) membranes (including membrane fouling) is studied using computational fluid dynamics (CFD) simulations. A model for film formation on a membrane surface is proposed for the first time to simulate film formation on membrane surfaces. The bulk multiphase flow is modeled using an Eulerian-Eulerian multiphase flow model. A wall film is developed from mass and momentum balances [3] and implemented to model droplet deposition and membrane surface blockage. The model is used to predict film formation and subsequent membrane fouling, and allow to estimate the actual permeate flux. The results are validated using available experimental data.

scholarly journals Influential Mechanism of Natural Organic Matters with Calcium Ion on the Anion Exchange Membrane Fouling Behavior via xDLVO Theory

Membranes ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 968
Author(s):  
Zhun Ma ◽  
Lu Zhang ◽  
Ying Liu ◽  
Xiaosheng Ji ◽  
Yuting Xu ◽  
...  
Keyword(s):  
Organic Matter ◽  
Interaction Energy ◽  
Anion Exchange ◽  
Natural Organic Matter ◽  
Calcium Ions ◽  
Membrane Fouling ◽  
Membrane Surface ◽  
Anion Exchange Membrane ◽  
Anion Exchange Membranes ◽  
Exchange Membrane

The fouling mechanism of the anion exchange membrane (AEM) induced by natural organic matter (NOM) in the absence and presence of calcium ions was systematically investigated via the extended Derjaguin–Landau–Verwey–Overbeek (xDLVO) approach. Sodium alginate (SA), humic acid (HA), and bovine serum albumin (BSA) were utilized as model NOM fractions. The results indicated that the presence of calcium ions tremendously aggravated the NOM fouling on the anion exchange membrane because of Ca-NOM complex formation. Furthermore, analysis of the interaction energy between the membrane surface and foulants via xDLVO revealed that short-range acid–base (AB) interaction energy played a significant role in the compositions of interaction energy during the electrodialysis (ED) process. The influence of NOM fractions in the presence of calcium ions on membrane fouling followed the order: SA > BSA > HA. This study demonstrated that the interaction energy was a dominating indicator for evaluating the tendency of anion exchange membranes fouling by natural organic matter.

Investigation of membrane fouling by synthetic and natural particles

2004 ◽  
Vol 50 (12) ◽  
pp. 279-285 ◽  
Author(s):  
J.H. Kweon ◽  
D.F. Lawler
Keyword(s):  
Organic Matter ◽  
Natural Organic Matter ◽  
Membrane Fouling ◽  
Membrane Surface ◽  
Research Articles ◽  
Clay Material ◽  
Dramatic Effect ◽  
Flux Decline ◽  
Scanning Electron

The biggest impediment for applying membrane processes is fouling that comes from mass flux (such as particle and organic matter) to the membrane surface and its pores. Numerous research articles have indicated that either particles or natural organic matter (NOM) has been the most detrimental foulant. Therefore, the role of particles in membrane fouling was investigated with two synthetic waters (having either particles alone or particles with simple organic matter) and a natural water. Membrane fouling was evaluated with flux decline behavior and direct images from scanning electron microscopy. The results showed that the combined fouling by kaolin and dextran (a simple organic compound selected as a surrogate for NOM) showed no difference from the fouling with only the organic matter. The similarity might stem from the fact that dextran (i.e., polysaccharide) has no ability to be adsorbed on the clay material, so that the polysaccharide behaves the same with respect to the membrane with or without clay material being present. In contrast to kaolin, the natural particles showed a dramatic effect on membrane fouling.

scholarly journals Recycling of Reverse Osmosis Concentrates to the Membrane Bioreactor in the MBR-RO Process for Water Reuse: effect on mbr performances

2017 ◽  
Vol 30 (1) ◽  
pp. 1-10 ◽  
Author(s):  
Thi Thu Nga Vu ◽  
Manon Montaner ◽  
Christelle Guigui
Keyword(s):  
Organic Matter ◽  
Reverse Osmosis ◽  
Membrane Fouling ◽  
Water Reuse ◽  
High Performance ◽  
Membrane Bioreactor ◽  
Membrane System ◽  
Size Exclusion ◽  
Ro Concentrate ◽  
The Impact

Wastewater effluents can be treated by an integrated membrane system combining membrane bioreactor (MBR) and reverse osmosis (RO) for effective removal of micropollutants in the field of high-quality water reuse. However, discharging the RO concentrate waste stream directly into the natural environment could lead to serious problems due to the toxic components contained in the concentrates (micropollutants, salts, organic matter). A possible solution could be the recirculation of RO concentrate waste to the MBR. However, such an operation should be studied in detail since the recirculation of non-biodegradable organic matter or high concentrations of salts and micropollutants could directly or indirectly contribute to MBR membrane fouling and modification of the biodegradation activity. In this context, the work reported here focused on the recirculation of such concentrates in an MBR, paying specific attention to MBR membrane fouling. Lab-scale experiments were performed on a continuous MBR-RO treatment line with RO concentrate recirculation. The main goal was to determine the recovery of the RO unit and of the global process that maintained good process performance in terms of biodegradation and MBR fouling. The results demonstrate that the impact of the toxic flow on activated sludge depends on the recovery of the RO step but the same trends were observed regardless of the organic matter and salt contents of the concentrates: the concentration of proteins increased slightly. Size-exclusion high performance liquid chromatography (HPLC-SEC) was employed to study the effects of RO concentrate on the production of protein-like soluble microbial products (SMPs) and demonstrated a significant peak of protein-like substances corresponding to 10-100 kDa and 100-1 000 kDa molecules in the supernatant. Thus a significant increase in the propensity for sludge fouling was observed, which could be attributed to the increased quantity of protein-like substances. Finally, the effect of the concentrate on sludge activity was studied and no significant effect was observed on biodegradation, indicating that the return of the concentrate to the MBR could be a good alternative.

Sign in / Sign up

Export Citation Format

Share Document