Roles of the Hydrophobic and Hydrophilic Groups of Collectors in the Flotation of Different-Sized Mineral Particles

Author(s):  
Mingxia Liu ◽  
Hong Yu ◽  
Hanquan Zhang ◽  
Kaipeng Wang ◽  
Xiaoli Tan ◽  
...  
Keyword(s):  
Author(s):  
G. M. Brown ◽  
D. F. Brown ◽  
J. H. Butler

The term “gel”, in the jargon of the plastics film industry, may refer to any inclusion that produces a visible artifact in a polymeric film. Although they can occur in any plastic product, gels are a principle concern in films where they detract from the cosmetic appearance of the product and may compromise its mechanical strength by acting as local stress concentrators. Many film gels are small spheres or ellipsoids less than one millimeter in diameter whereas other gels are fusiform-shaped and may reach several centimeters in length. The actual composition of gel inclusions may vary from miscellaneous inorganics (i.e. glass and mineral particles) and processing additives to heavily oxidized, charred or crosslinked polymer. The most commonly observed gels contain polymer differing from the bulk of the sample in its melt viscosity, density or molecular weight.Polymeric gels are a special concern in polyethylene films. Over the years and with the examination of a variety of these samples three predominant polymeric species have been observed: density gels which have different crystallinity than the film; melt-index gels in which the molecular weight is different than the film and crosslinked gels which are comprised of crosslinked polyethylene.


Author(s):  
Karen A. Katrinak ◽  
James R. Anderson ◽  
Peter R. Buseck

Aerosol samples were collected in Phoenix, Arizona on eleven dates between July 1989 and April 1990. Elemental compositions were determined for approximately 1000 particles per sample using an electron microprobe with an energy-dispersive x-ray spectrometer. Fine-fraction samples (particle cut size of 1 to 2 μm) were analyzed for each date; coarse-fraction samples were also analyzed for four of the dates.The data were reduced using multivariate statistical methods. Cluster analysis was first used to define 35 particle types. 81% of all fine-fraction particles and 84% of the coarse-fraction particles were assigned to these types, which include mineral, metal-rich, sulfur-rich, and salt categories. "Zero-count" particles, consisting entirely of elements lighter than Na, constitute an additional category and dominate the fine fraction, reflecting the importance of anthropogenic air pollutants such as those emitted by motor vehicles. Si- and Ca-rich mineral particles dominate the coarse fraction and are also numerous in the fine fraction.


2000 ◽  
Vol 15 (2) ◽  
pp. 88-97 ◽  
Author(s):  
Lars Järnström ◽  
Magnus Wikström ◽  
Mikael Rigdahl
Keyword(s):  

2021 ◽  
Vol 773 (1) ◽  
pp. 012088
Author(s):  
IA Matveev ◽  
BV Yakovlev ◽  
NG Eremeeva ◽  
TP Kulichkina

1999 ◽  
Vol 40 (11-12) ◽  
pp. 223-229 ◽  
Author(s):  
Frédéric Clauss ◽  
Christel Balavoine ◽  
Delphine Hélaine ◽  
Gaëtan Martin

Forest industry wastewaters are difficult to clean: hydraulic and organic load variations, filamentous bulking or pin-point flocs negatively impact depollution processes. The addition of a fine, mineral, talc-based powder, Aquatal, into the aeration tanks of wastewater treatment plants connected to pulp and paper factories has been successfully tested since end of '97. The first case-study presents full results obtained over a period of 18 months in a 20,000 p.e. plant connected to a paper factory. The mineral powder was regularly added to control sludge volume index, thereby ensuring low suspended solids concentration in the outfluent. Plant operators could easily adapt biomass concentration to match organic load variation, thereby maintaining pollution micro-organisms ratio constant. In a second case study, a trouble-shooting strategy was implemented to counteract filamentous bulking. A one-off, large dosage enabled the plant operator to deal effectively with poor settleability sludge and rapidly control sludge blanket expansion. In both cases, the main common characteristics observed were an increase in floc aggregation and the production of heavier and well-structured flocs. The sludge settling velocity increased and an efficient solid/liquid separation was obtained. After a few days, the mineral particles of Aquatal were progressively integrated into the sludge floc structure. When the mineral powder was added to the activated sludge in the aeration basin, chemical interactions frequently encountered with other wastewater treatment additives did not pose a problem. Moreover, with this mineral additive, the biological excess sludge displayed good thickening properties and dewatering was improved. Despite the addition of the insoluble mineral particles, the amount of wet sludge expelled did not increase. Aquatal offers a rapid solution to floc settleability problems which so frequently arise when physical or biological disorders appear in forest industry wastewater treatment plants.


2013 ◽  
Vol 752 ◽  
pp. 209-216 ◽  
Author(s):  
Róbert Géber ◽  
László A. Gömze

The present research work deals with the examination and rheological modelling of flow properties of asphalt mastics which are the most important components of asphalt concretes. Asphalt mastics are mixtures of fine grained mineral filler particles (d<0,063 mm) and bitumen, having a stabilizing role in asphalt mixtures and largely determining the cohesion between mineral particles and bitumen. During our examinations two types of mineral fillers – limestone and dolomite – as well as standard bitumen were tested, which are extensively used in Hungarian road construction. Asphalt mastic mixtures were prepared out of these materials and they were tested with dynamic shear rheometer (DSR). According to the test results, rheological models of mastics were determined. It has been established that at different test temperatures and shear rate ranges asphalt mastics behave as Herschel-Bulkley and Bingham-type materials.


Sign in / Sign up

Export Citation Format

Share Document