Estimating compressive strength of modern concrete mixtures using computational intelligence: A systematic review

2021 ◽  
Vol 310 ◽  
pp. 125279
Author(s):  
Itzel Nunez ◽  
Afshin Marani ◽  
Majdi Flah ◽  
Moncef L. Nehdi
Keyword(s):  
Systematic Review ◽  
Compressive Strength ◽  
Computational Intelligence ◽  
Concrete Mixtures

scholarly journals The Effect of Recycled HDPE Plastic Additions on Concrete Performance

Recycling ◽  
2021 ◽  
Vol 6 (1) ◽  
pp. 18
Author(s):  
Tamrin ◽  
Juli Nurdiana
Keyword(s):  
Compressive Strength ◽  
High Density Polyethylene ◽  
Concrete Mixtures ◽  
Best Response ◽  
Structural Applications ◽  
Optimal Mix ◽  
Increased Strength ◽  
Selection Of ◽  
Recycled Hdpe ◽  
Lower Medium

This study examined HDPE (high-density polyethylene) plastic waste as an added material for concrete mixtures. The selection of HDPE was based on its increased strength, hardness, and resistance to high temperatures compared with other plastics. It focused on how HDPE plastic can be used as an additive in concrete to increase its tensile strength and compressive strength. 156 specimens were used to identify the effect of adding different percentages and sizes of HDPE lamellar particles to lower, medium, and higher strength concrete for non-structural applications. HDPE 0.5 mm thick lamellar particles with sizes of 10 × 10 mm, 5 × 20 mm, and 2.5 × 40 mm were added at 2.5%, 5%, 10%, and 20% by weight of cement. The results showed that the medium concrete class (with compressive strength equal to 10 MPa) had the best response to the addition of HDPE. The 5% HDPE addition represented the optimal mix for all concrete types, while the 5 × 20 mm size was best.

scholarly journals Examining Polyethylene Terephthalate (PET) as Artificial Coarse Aggregates in Concrete

2020 ◽  
Vol 6 (12) ◽  
pp. 2416-2424
Author(s):  
Erniati Bachtiar ◽  
Mustaan Mustaan ◽  
Faris Jumawan ◽  
Meldawati Artayani ◽  
Tahang Tahang ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Polyethylene Terephthalate ◽  
Coarse Aggregate ◽  
Fresh Concrete ◽  
Coarse Aggregates ◽  
Volume Weight ◽  
Concrete Mixtures ◽  
Strength Tests ◽  
Recycled Polyethylene

This study aims to examine the effect of recycled Polyethylene Terephthalate (PET) artificial aggregate as a substitute for coarse aggregate on the compressive strength and flexural strength, and the volume weight of the concrete. PET plastic waste is recycled by heating to a boiling point of approximately 300°C. There are five variations of concrete mixtures, defined the percentage of PET artificial aggregate to the total coarse aggregate, by 0, 25, 50, 75 and 100%. Tests carried out on fresh concrete mixtures are slump, bleeding, and segregation tests. Compressive and flexural strength tests proceeded based on ASTM 39/C39M-99 and ASTM C293-79 standards at the age of 28 days. The results showed that the use of PET artificial aggregate could improve the workability of the concrete mixture. The effect of PET artificial aggregate as a substitute for coarse aggregate on the compressive and flexural strength of concrete is considered very significant. The higher the percentage of PET plastic artificial aggregate, the lower the compressive and flexural strength, and the volume weight, of the concrete. Substitution of 25, 50, 75 and 100% of PET artificial aggregate gave decreases in compressive strength of 30.06, 32.39, 41.73 and 44.06% of the compressive strength of the standard concrete (18.20 MPa), respectively. The reductions in flexural strength were by respectively 19.03, 54.50, 53.95 and 61.00% of the standard concrete's flexural strength (3.59 MPa). The reductions in volume weight of concrete were by respectively 8.45, 17.71, 25.07 and 34.60% of the weight of the standard concrete volume of 2335.4 kg/m3 Doi: 10.28991/cej-2020-03091626 Full Text: PDF

Compressive Strength of Concrete from Lightweight Bubbles Aggregate

2015 ◽  
Vol 754-755 ◽  
pp. 348-353 ◽  
Author(s):  
Norlia Mohamad Ibrahim ◽  
Leong Qi Wen ◽  
Mustaqqim Abdul Rahim ◽  
Khairul Nizar Ismail ◽  
Roshazita Che Amat ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Compressive Strength ◽  
Natural Resources ◽  
Concrete Structure ◽  
Concrete Mixture ◽  
New Materials ◽  
Concrete Mixtures ◽  
Compressive Strength Of Concrete

Compressive strength of concrete is the major mechanical properties of concrete that need to be focused on. Poor compressive strength will lead to low susceptibility of concrete structure towards designated actions. Many researches have been conducted to enhance the compressive strength of concrete by incorporating new materials in the concrete mixture. The dependencies towards natural resources can be reduced. Therefore, this paper presents the results of an experimental study concerning the incorporation of artificial lightweight bubbles aggregate (LBA) into cementations mixture in order to produce comparable compressive strength but at a lower densities. Three concrete mixtures containing various percentages of LBA, (10% - 50% of LBA) and one mixture used normal aggregate (NA) were prepared and characterized. The compressive strength of LBA in concrete was identified to be ranged between 39 MPa and 54 MPa. Meanwhile, the densities vary between 2000 kg/m3 to 2300 kg/m3.

Properties of High Strength Concrete with Calcined Diatomaceous Earth as Cement Replacement under Compression

2020 ◽  
Vol 402 ◽  
pp. 7-13
Author(s):  
Muttaqin Hasan ◽  
Aris Muyasir ◽  
Taufiq Saidi ◽  
Husaini ◽  
Raudha Azzahra
Keyword(s):  
Compressive Strength ◽  
Modulus Of Elasticity ◽  
High Strength Concrete ◽  
Diatomaceous Earth ◽  
High Strength ◽  
Compression Load ◽  
Strength Concrete ◽  
Cement Replacement ◽  
Concrete Mixtures ◽  
Compressive Strength Of Concrete

In this research, calcined diatomaceous earth from Aceh Besar, Indonesia was used as cement replacement in producing high strength concrete. Four concrete mixtures in which the percentage of cement replacement of 0%, 5%, 10% and 15% by weight were studied. Four cylinder-specimens with 100 mm diameter and 200 mm high were prepared for each mixture. The compression load was applied on the specimens at the age of 28 days until the specimens failed. The mixture without calcined diatomaceous earth was more workable than that with diatomaceous earth. The compressive strength of concrete with diatomaceous earth in this study was almost the same for all mixture. However, those compressive strength was lower than the compressive strength of concrete without calcined diatomaceous earth for about 14.6%. Modulus of elasticity of high strength concrete decreased with increasing of cement replacement percentage.

scholarly journals Predicting Infections Using Computational Intelligence – A Systematic Review

IEEE Access ◽  
2020 ◽  
Vol 8 ◽  
pp. 31083-31102 ◽  
Author(s):  
Alejandro Baldominos ◽  
Adrian Puello ◽  
Hasan Ogul ◽  
Tunc Asuroglu ◽  
Ricardo Colomo-Palacios
Keyword(s):  
Systematic Review ◽  
Computational Intelligence

scholarly journals The Influence of Discharge Time, Kind of Additive, and Kind of Aggregate on the Properties of Three-Stage Mixed Concrete

2018 ◽  
Vol 10 (11) ◽  
pp. 3862 ◽  
Author(s):  
Alena Sicakova ◽  
Karol Urban
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Recycled Concrete ◽  
Recycled Aggregates ◽  
Concrete Aggregate ◽  
Discharge Time ◽  
Concrete Mixtures ◽  
Concrete Properties ◽  
Concrete Production ◽  
The Impact

Application of recycled aggregates (RA) for concrete production is limited due to their poor quality. While the environmental benefits of using the RA are well accepted, some unsolved problems prevent this type of material from wide application in structural concrete. The research and development of techniques which can minimize the adverse effect of RA on the concrete properties are highly requested. A specific mixing approach can also be helpful; here, mineral additives play a significant role for improvement of RA performance within the mixing process. However, delivery process can influence the homogeneity and uniformity of the concrete mixtures, resulting in negative effect on technical parameters. In this study, the impact of delivery time (0 min, 45 min, and 90 min) on the set of hardened concrete properties is presented while the three-stage mixing is used. Two kinds of additives—fly ash (FA) and recycled concrete powder (RCP)—were tested to coat the coarse fraction of recycled concrete aggregate (RCA) in the first step of mixing. For comparison, cement as coating material and natural aggregate instead the RCA were also used. The following parameters were tested after 28 days of setting and hardening: density, compressive strength, splitting tensile strength, water absorption capacity, and depth of penetration of water under pressure. Generally, 90 min of working with concrete mixtures left no significantly negative influence on tested characteristics. Based on ANOVA results, with prolonged discharge time, the changes in composition of the mixtures become less important for compressive strength, density, and water absorption.

scholarly journals Estimation of In-situ concrete strength using drilling resistance

2019 ◽  
Vol 289 ◽  
pp. 06001
Author(s):  
Serkan Karatosun ◽  
Muhammet Asan ◽  
Oguz Gunes
Keyword(s):  
Compressive Strength ◽  
Concrete Strength ◽  
Condition Assessment ◽  
Assessment Practice ◽  
Destructive Testing ◽  
Seismic Safety ◽  
Concrete Mixtures ◽  
Priority Task ◽  
Compressive Strength Of Concrete ◽  
Drilling Resistance

Rapid and reliable condition assessment of reinforced concrete structures in high seismicity regions is a priority task in estimating their seismic safety. Non-destructive testing (NDT) methods may contribute to the condition assessment practice by providing fast and reliable strength estimation while causing minimal or no damage to the structure. Drilling resistance is an NDT method that has been used for mechanical characterization of natural stone and wood by measuring the force response for constant penetration rate and rotational speed. This paper focuses on the relationship between drilling resistance and compressive strength of concrete, including when it is combined with other NDT methods. Concrete cube samples produced using 6 different concrete mixtures were tested. Correlation equations were then obtained using statistical analysis. The results reveal that it may be possible to reliably estimate the compressive strength of concrete using drilling resistance method.

scholarly journals Durability of concretes prepared with crystalline admixtures

2019 ◽  
Vol 289 ◽  
pp. 09003
Author(s):  
Kosmas K. Sideris ◽  
A. Chatzopoulos ◽  
Ch. Tassos ◽  
P. Manita
Keyword(s):  
Compressive Strength ◽  
Concrete Slab ◽  
Concrete Mixtures ◽  
Durability Of Concrete

The objective of this work was to study the influence of crystalline admixtures on the durability of concrete. Four concrete mixtures – two reference concretes and two alternative mixtures-were produced during the first phase of the research. Influence of curing on the activation of the crystals was investigated on concrete slab specimens. The properties measured were the compressive strength and different durability indicators. The results revealed that crystalline admixtures enhanced the strength and the durability of the alternative mixtures.

Sign in / Sign up

Export Citation Format

Share Document