Effect of non-associated flow rule on fracture prediction of metal sheets using a novel anisotropic ductile fracture criterion

2021 ◽  
Vol 195 ◽  
pp. 106224
Author(s):  
Hung Quach ◽  
Young-Suk Kim
Keyword(s):  
Ductile Fracture ◽  
Fracture Criterion ◽  
Fracture Prediction ◽  
Flow Rule ◽  
Ductile Fracture Criterion ◽  
Metal Sheets ◽  
Associated Flow Rule

Fracture Prediction in Sheet Metal Stamping Based on a Modified Ductile Fracture Criterion

2015 ◽  
Vol 639 ◽  
pp. 543-550
Author(s):  
Rong Zeng ◽  
Liang Huang ◽  
Jian Jun Li
Keyword(s):  
Ductile Fracture ◽  
Sheet Metal ◽  
Fracture Criterion ◽  
Fracture Prediction ◽  
Uniaxial Tensile ◽  
Ductile Fracture Criterion ◽  
Fracture Criteria ◽  
Sheet Metal Stamping ◽  
Ductile Fracture Criteria ◽  
Metal Stamping

Sheet metal stamping is an important manufacturing process because of its high production rate and low cost, so the fracture prediction of stamping parts has become important issues. Recent experimental studies have shown that the quality of stamping parts can be increased by using ductile fracture criteria. This paper proposed a modified ductile fracture criterion based on the macroscopic and microscopic continuum damage mechanics (CDM). Three-dimensional (3D) explicit finite element analysis (FEA) are performed to predict the fracture behaviors of sheet metal stamping process. An approach to determine the material constants of modified ductile fracture criterion is presented with the help of uniaxial tensile tests and compressive tests. The results show that the modified ductile fracture criterion enables precise cup depth and fracture location of sheet metal stamping under nonlinear paths. Compared with typical ductile fracture criteria, the results predicted with modified ductile fracture criterion correlate the best with the experimental data.

scholarly journals Comparison of Modified Mohr–Coulomb Model and Bai–Wierzbicki Model for Constructing 3D Ductile Fracture Envelope of AA6063

2021 ◽  
Vol 34 (1) ◽  
Author(s):  
Jianye Gao ◽  
Tao He ◽  
Yuanming Huo ◽  
Miao Song ◽  
Tingting Yao ◽  
...  
Keyword(s):  
Ductile Fracture ◽  
Fracture Criterion ◽  
Fracture Strain ◽  
Stress Triaxiality ◽  
Ductile Fracture Criterion ◽  
Forming Process ◽  
Tension Tests ◽  
Wide Range ◽  
Round Bar ◽  
Fracture Envelope

AbstractDuctile fracture of metal often occurs in the plastic forming process of parts. The establishment of ductile fracture criterion can effectively guide the selection of process parameters and avoid ductile fracture of parts during machining. The 3D ductile fracture envelope of AA6063-T6 was developed to predict and prevent its fracture. Smooth round bar tension tests were performed to characterize the flow stress, and a series of experiments were conducted to characterize the ductile fracture firstly, such as notched round bar tension tests, compression tests and torsion tests. These tests cover a wide range of stress triaxiality (ST) and Lode parameter (LP) to calibrate the ductile fracture criterion. Plasticity modeling was performed, and the predicted results were compared with corresponding experimental data to verify the plasticity model after these experiments. Then the relationship between ductile fracture strain and ST with LP was constructed using the modified Mohr–Coulomb (MMC) model and Bai-Wierzbicki (BW) model to develop the 3D ductile fracture envelope. Finally, two ductile damage models were proposed based on the 3D fracture envelope of AA6063. Through the comparison of the two models, it was found that BW model had better fitting effect, and the sum of squares of residual error of BW model was 0.9901. The two models had relatively large errors in predicting the fracture strain of SRB tensile test and torsion test, but both of the predicting error of both two models were within the acceptable range of 15%. In the process of finite element simulation, the evolution process of ductile fracture can be well simulated by the two models. However, BW model can predict the location of fracture more accurately than MMC model.

scholarly journals Finite Element Analysis of Bore-expanding Processes with Ductile Fracture Criterion

1998 ◽  
Vol 84 (3) ◽  
pp. 182-187 ◽  
Author(s):  
Hirohiko TAKUDA ◽  
Ken-ichiro MORI ◽  
Masashi KANESHIRO ◽  
Natsuo HATTA
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Ductile Fracture ◽  
Fracture Criterion ◽  
Ductile Fracture Criterion ◽  
Element Analysis
Sign in / Sign up

Export Citation Format

Share Document