Hybrid additive manufacture: surface finishing methods for improving conductivity of inkjet printed tracks on non-planar substrates fabricated using fused deposition modelling

2021 ◽  
pp. 113235
Author(s):  
Elliott R Griffiths ◽  
Simon J Leigh
Keyword(s):  
Surface Finishing ◽  
Additive Manufacture ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Planar Substrates

Localised Pre-Heating to Improve Inter-Layer Delamination Strength in Fused Deposition Modelling

2019 ◽  
Author(s):  
Andrew Aitchison ◽  
Qing Wang
Keyword(s):  
Tensile Strength ◽  
Thermal Energy ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Additive Manufacture ◽  
Fused Deposition Modelling ◽  
Print Quality ◽  
Air Gaps ◽  
Fused Deposition ◽  
Air Temperatures

Abstract Additive manufacture, specifically Fused Deposition Modeling (FDM), is an advancing manufacture method opening up new possibilities in design previously impossible to machine, in a relatively affordable way. However, its use in functional products is limited due to anisotropic strength and reduced strength from injection molded components. This paper aims to increase the tensile strength of Acrylonitrile Butadiene Styrene (ABS) in the weakest direction (Z axis), where poor interlayer fusion and air gaps between extruded trails reduce strength. Extra thermal energy was applied to the top surface layer during the printing process (through hot air) to encourage more polymer chain diffusion across the boundary, and spreading out to fill air gaps. Multiple tensile test samples were printed at a variety of heat levels. The ultimate tensile strength σuts was plotted against these temperatures and a weak positive correlation was found. However, only air temperatures above 81°C increased strength past the control to a maximum of 1.4MPa. Heat application has proven to increase tensile strength, but needs to be applied with a more precise method, to the boundary interface, to allow greater thermal energy transfer without sacrificing print quality.

scholarly journals Representative Volume Element (RVE) Analysis for Mechanical Characterization of Fused Deposition Modeled Components

Polymers ◽  
2021 ◽  
Vol 13 (20) ◽  
pp. 3555
Author(s):  
Patrich Ferretti ◽  
Gian Maria Santi ◽  
Christian Leon-Cardenas ◽  
Elena Fusari ◽  
Giampiero Donnici ◽  
...  
Keyword(s):  
Representative Volume Element ◽  
Low Cost ◽  
Volume Element ◽  
Additive Manufacture ◽  
Fused Deposition Modelling ◽  
Structural Element ◽  
Fused Deposition ◽  
Representative Volume ◽  
Wide Range ◽  
3D Printed

Additive manufacturing processes have evolved considerably in the past years, growing into a wide range of products through the use of different materials depending on its application sectors. Nevertheless, the fused deposition modelling (FDM) technique has proven to be an economically feasible process turning additive manufacture technologies from consumer production into a mainstream manufacturing technique. Current advances in the finite element method (FEM) and the computer-aided engineering (CAE) technology are unable to study three-dimensional (3D) printed models, since the final result is highly dependent on processing and environment parameters. Because of that, an in-depth understanding of the printed geometrical mesostructure is needed to extend FEM applications. This study aims to generate a homogeneous structural element that accurately represents the behavior of FDM-processed materials, by means of a representative volume element (RVE). The homogenization summarizes the main mechanical characteristics of the actual 3D printed structure, opening new analysis and optimization procedures. Moreover, the linear RVE results can be used to further analyze the in-deep behavior of the FDM unit cell. Therefore, industries could perform a feasible engineering analysis of the final printed elements, allowing the FDM technology to become a mainstream, low-cost manufacturing process in the near future.

scholarly journals Computer Numerical Controlled Grinding and Physical Vapor Deposition for Fused Deposition Modelled Workpieces

2018 ◽  
Vol 2018 ◽  
pp. 1-7 ◽  
Author(s):  
Fulvio Lavecchia ◽  
Gianluca Percoco ◽  
Eujin Pei ◽  
Luigi Maria Galantucci
Keyword(s):  
Vapor Deposition ◽  
Physical Vapor Deposition ◽  
High Surface ◽  
Extrusion Process ◽  
Surface Finishing ◽  
Fused Deposition Modelling ◽  
Layer By Layer ◽  
Fused Deposition ◽  
Test Pieces ◽  
Pvd Coating

The use of additive manufacturing (AM) enables companies to directly produce complex end-use parts. Fused deposition modelling (FDM) is an AM technology based on an extrusion process of fabricating parts. This layer-by-layer method results in a poor surface finish, and as a result, manual finishing is often required, which consequentially reduces the definition of the geometrical features. This research proposes a novel way of achieving high surface finishing by using additive and finishing processes, followed by a physical vapor deposition (PVD) coating. Two test pieces were produced, the first one was subjected to computer numerical controlled (CNC) mechanical grinding with appropriate grades of grindstones; the second one was subjected to microsandblasting to remove excess material and the stair-stepping effect. Both test pieces were then subjected to a PVD coating process to provide a metal thin film. To benchmark the test pieces, the authors used a coordinate measure machine for dimensions and a roughness meter to verify the effectiveness of this postprocessing approach.

scholarly journals RANCANG BANGUN KONTRUKSI DAN SISTEM GERAK SUMBU PADA MESIN FUSED DEPOSITION MODELLING

POROS ◽  
2017 ◽  
Vol 14 (2) ◽  
pp. 99
Author(s):  
Jeffrey Jeffrey ◽  
Didi Widya Utama ◽  
Gatot Soeharsono
Keyword(s):  
Modeling And Simulation ◽  
3D Modeling ◽  
Fused Deposition Modeling ◽  
Physical Models ◽  
Additive Manufacture ◽  
Fused Deposition Modelling ◽  
Design Tools ◽  
Fused Deposition ◽  
3D Printers ◽  
Deposition Modeling

Abstract: Fused Deposition Modelling (FDM) is a technology additive manufacture for modelling, prototyping, and production. This technology is one of the techniques used for 3D printers. Our focus is on studying, design machines fused deposition with 3D modeling and simulation with autodesk inventor and other design tools. Design is done by simulating the strength of the construction and then determine the components needed. We are making fused deposition modeling is intended as a prototype in order to understand how it works and how to innovate in the development of fused deposition modeling. The results of the design in the form of a fused depositon modeling that is able to create physical models 

Evaluation of geometrical benchmark artifacts containing multiple overhang lengths fabricated using material extrusion technique

2020 ◽  
Vol 14 (3) ◽  
pp. 7296-7308
Author(s):  
Siti Nur Humaira Mazlan ◽  
Aini Zuhra Abdul Kadir ◽  
N. H. A. Ngadiman ◽  
M.R. Alkahari
Keyword(s):  
3D Model ◽  
Laser Scanner ◽  
Dimensional Accuracy ◽  
Fused Deposition Modelling ◽  
Layer By Layer ◽  
Fused Deposition ◽  
Layer Technique ◽  
Subtractive Manufacturing ◽  
Manufacturing Features ◽  
Layer Problem

Fused deposition modelling (FDM) is a process of joining materials based on material entrusion technique to produce objects from 3D model using layer-by-layer technique as opposed to subtractive manufacturing. However, many challenges arise in the FDM-printed part such as warping, first layer problem and elephant food that was led to an error in dimensional accuracy of the printed parts especially for the overhanging parts. Hence, in order to investigate the manufacturability of the FDM printed part, various geometrical and manufacturing features were developed using the benchmarking artifacts. Therefore, in this study, new benchmarking artifacts containing multiple overhang lengths were proposed. After the benchmarking artifacts were developed, each of the features were inspected using 3D laser scanner to measure the dimensional accuracy and tolerances. Based on 3D scanned parts, 80% of the fabricated parts were fabricated within ±0.5 mm of dimensional accuracy as compared with the CAD data. In addition, the multiple overhang lengths were also successfully fabricated with a very significant of filament sagging observed.

scholarly journals Current State and Challenges of Natural Fibre-Reinforced Polymer Composites as Feeder in FDM-Based 3D Printing

Polymers ◽  
2021 ◽  
Vol 13 (14) ◽  
pp. 2289
Author(s):  
Nishata Royan Rajendran Royan ◽  
Jie Sheng Leong ◽  
Wai Nam Chan ◽  
Jie Ren Tan ◽  
Zainon Sharmila Binti Shamsuddin
Keyword(s):  
Mechanical Properties ◽  
Natural Fibre ◽  
Critical Discussion ◽  
Fused Deposition Modelling ◽  
Preparation Methods ◽  
Fused Deposition ◽  
Current State ◽  
Future Challenges ◽  
Raster Angle ◽  
Fibre Reinforced Polymer

As one of the fastest-growing additive manufacturing (AM) technologies, fused deposition modelling (FDM) shows great potential in printing natural fibre-reinforced composites (NFRC). However, several challenges, such as low mechanical properties and difficulty in printing, need to be overcome. Therefore, the effort to improve the NFRC for use in AM has been accelerating in recent years. This review attempts to summarise the current approaches of using NFRC as a feeder for AM. The effects of fibre treatments, composite preparation methods and addition of compatibilizer agents were analysed and discussed. Additionally, current methods of producing feeders from NFRCs were reviewed and discussed. Mechanical property of printed part was also dependent on the printing parameters, and thus the effects of printing temperature, layer height, infill and raster angle were discussed, and the best parameters reported by other researchers were identified. Following that, an overview of the mechanical properties of these composites as reported by various researchers was provided. Next, the use of optimisation techniques for NFRCs was discussed and analysed. Lastly, the review provided a critical discussion on the overall topic, identified all research gaps present in the use of NFRC for AM processes, and to overcome future challenges.

Sign in / Sign up

Export Citation Format

Share Document