An adaptive order-band energy ratio method for the fault diagnosis of planetary gearboxes

2022 ◽  
Vol 165 ◽  
pp. 108336
Author(s):  
Mian Zhang ◽  
Decai Li ◽  
KeSheng Wang ◽  
Qing Li ◽  
Yue Ma ◽  
...  
Author(s):  
Guoshi Wang ◽  
Ying Liu ◽  
Xiaowen Chen ◽  
Qing Yan ◽  
Haibin Sui ◽  
...  

Abstract Transformer is the most important equipment in the power system. The research and development of fault diagnosis technology for Internet of Things equipment can effectively detect the operation status of equipment and eliminate hidden faults in time, which is conducive to reducing the incidence of accidents and improving people's life safety index. Objective To explore the utility of Internet of Things in power transformer fault diagnosis system. Methods A total of 30 groups of transformer fault samples were selected, and 10 groups were randomly selected for network training, and the rest samples were used for testing. The matter-element extension mathematical model of power transformer fault diagnosis was established, and the correlation function was improved according to the characteristics of three ratio method. Each group of power transformer was diagnosed for four months continuously, and the monitoring data and diagnosis were recorded and analyzed result. GPRS communication network is used to complete the communication between data acquisition terminal and monitoring terminal. According to the parameters of the database, the working state of the equipment is set, and various sensors are controlled by the instrument driver module to complete the diagnosis of transformer fault system. Results The detection success rate of the power transformer fault diagnosis system model established in this paper is as high as 95.6%, the training error is less than 0.0001, and it can correctly identify the fault types of the non training samples. It can be seen that the technical support of the Internet of Things is helpful to the upgrading and maintenance of the power transformer fault diagnosis system.


2014 ◽  
Vol 571-572 ◽  
pp. 201-204
Author(s):  
Jian Li Yu ◽  
Zhe Zhang

According to the characteristics of fault types of the transformer ,RBF neural network is used to diagnose transformer fault. The paper regards six gases as inputs of the neural network and establishes RBF neural network model which can diagnose six transformer faults: low temperature overheat, medium temperature overheat, high temperature overheat, low energy discharge, high energy discharge and partial discharge . The Matlab simulation studies show that transformer fault diagnosis model based on RBF neural network diagnosis for failure beyond the traditional three-ratio method. The rate of the transformer fault diagnosis accuracy reaches 91.67% which is also much higher than the traditional three ratio method.


Energies ◽  
2019 ◽  
Vol 12 (21) ◽  
pp. 4170 ◽  
Author(s):  
Bing Zeng ◽  
Jiang Guo ◽  
Wenqiang Zhu ◽  
Zhihuai Xiao ◽  
Fang Yuan ◽  
...  

Dissolved gas analysis (DGA) is a widely used method for transformer internal fault diagnosis. However, the traditional DGA technology, including Key Gas method, Dornenburg ratio method, Rogers ratio method, International Electrotechnical Commission (IEC) three-ratio method, and Duval triangle method, etc., suffers from shortcomings such as coding deficiencies, excessive coding boundaries and critical value criterion defects, which affect the reliability of fault analysis. Grey wolf optimizer (GWO) is a novel swarm intelligence optimization algorithm proposed in 2014 and it is easy for the original GWO to fall into the local optimum. This paper presents a new meta-heuristic method by hybridizing GWO with differential evolution (DE) to avoid the local optimum, improve the diversity of the population and meanwhile make an appropriate compromise between exploration and exploitation. A fault diagnosis model of hybrid grey wolf optimized least square support vector machine (HGWO-LSSVM) is proposed and applied to transformer fault diagnosis with the optimal hybrid DGA feature set selected as the input of the model. The kernel principal component analysis (KPCA) is used for feature extraction, which can decrease the training time of the model. The proposed method shows high accuracy of fault diagnosis by comparing with traditional DGA methods, least square support vector machine (LSSVM), GWO-LSSVM, particle swarm optimization (PSO)-LSSVM and genetic algorithm (GA)-LSSVM. It also shows good fitness and fast convergence rate. Accuracies calculated in this paper, however, are significantly affected by the misidentifications of faults that have been made in the DGA data collected from the literature.


2012 ◽  
Vol 472-475 ◽  
pp. 795-798
Author(s):  
Min Yong Tong

A diagnosis method using wavelet packet, frequency band energy analysis and neural network was presented for the automobile engine fault diagnosis. Fault signal of automobile engine was decomposed at different frequency band by wavelet packet. According to the change of frequency band energy, fault frequency band of the automobile engine was found. Fault diagnosis knowledge is described by means of applying T-S model. Results from the experimental signal analysis show that the proposed method is effective in diagnosing the automobile engine faults.


2014 ◽  
Vol 971-973 ◽  
pp. 1288-1291 ◽  
Author(s):  
Zi Liang Yao ◽  
Min Wang ◽  
Tao Zan ◽  
Guo Fu Liu

The process of grinding chatter is divided into three states: stable grinding state, chatter gestation state and chatter state. The vibration signals of grinding process contain chatter features can correspond well to the changes of grinding process. By analyzing the natural frequency band energy ratio of grinding process, a method of grinding chatter prediction is proposed. Experimental results show that the natural frequency band energy ratio is beyond a certain threshold, chatter occurred, otherwise no chatter happened. The method of grinding prediction can provide reference for vibration monitoring in practice.


2015 ◽  
Vol 45 (1) ◽  
pp. 37-40 ◽  
Author(s):  
Jintao Gu ◽  
Meiping Sheng

Energy ratio method (ERM), which is a widely used method for coupling loss factors (CLFs) measurement, may lead to numerical problems because of the inversion of a large dimension matrix. The improved energy ratio method proposed here simplified a series several-coupled system into a two-coupled system so that it becomes a two dimensions matrix instead of large dimensions one. Coupling loss factors of a series three-coupled structure are measured using this method. Vibrating responses of the structure has been tested and predicted with loss and coupling loss factors measured here in order to verify the accuracy of measured CLFs. The agreement of vibrating responses indicates the fact that the improved energy ratio method is of great accuracy and reliability.


2020 ◽  
Vol 145 ◽  
pp. 02067
Author(s):  
Yanping Li ◽  
Yong Li ◽  
Yunqi Li

The production principle of characteristic gas in transformer oil and its corresponding transformer fault type are discussed in this paper. Aiming at the fault of multiple characteristic gases exceeding the standard in a 110 kV transformer oil, this paper analyzed the fault reasons according to the characteristic gas method and the three-ratio method, and combined with relevant tests, it was judged that the transformer core multiple grounding fault caused the fault. The on-site inspection verifies the correctness of the failure analysis results and the corresponding measures were adopted to eliminate the transformer faults.


2017 ◽  
Author(s):  
Xiong Ma* ◽  
Guofa Li ◽  
Hequn Li
Keyword(s):  

Sign in / Sign up

Export Citation Format

Share Document