scholarly journals Confinements regulate capillary instabilities of fluid threads

2019 ◽  
Vol 873 ◽  
pp. 816-834 ◽  
Author(s):  
Xiaodong Chen ◽  
Chundong Xue ◽  
Guoqing Hu
Keyword(s):  
Capillary Pressure ◽  
Flow Rate ◽  
External Flow ◽  
The Other ◽  
Low Flow ◽  
Critical Conditions ◽  
Flow Rates ◽  
Confined Fluid ◽  
Capillary Instabilities ◽  
Stop Flow

We study the breakup of confined fluid threads at low flow rates to understand instability mechanisms. To determine the critical conditions between the earlier quasi-stable necking stage and the later unstable collapse stage, simulations and experiments are designed to operate at an extremely low flow rate. The critical mean radii at the neck centres are identified by the stop-flow method for elementary microfluidic configurations. Two distinct origins of capillary instabilities are revealed for different confinement situations. One is the gradient of capillary pressure induced by the confinements of geometry and external flow, whereas the other is the competition between the capillary pressure and internal pressure determined by the confinements.

Assessment of the Use of Humidified Nasal Cannulas for Oxygen Therapy in Patients with Epistaxis

ORL ◽  
2021 ◽  
pp. 1-5
Author(s):  
Jingjing Liu ◽  
Tengfang Chen ◽  
Zhenggang Lv ◽  
Dezhong Wu
Keyword(s):  
Flow Rate ◽  
Oxygen Therapy ◽  
Preliminary Investigation ◽  
Nasal Cannula ◽  
Low Flow ◽  
Antiplatelet Drugs ◽  
Flow Rates ◽  
The Past ◽  
Oxygen Inhalation ◽  
Significant Difference

<b><i>Introduction:</i></b> In China, nasal cannula oxygen therapy is typically humidified. However, it is difficult to decide whether to suspend nasal cannula oxygen inhalation after the nosebleed has temporarily stopped. Therefore, we conducted a preliminary investigation on whether the use of humidified nasal cannulas in our hospital increases the incidence of epistaxis. <b><i>Methods:</i></b> We conducted a survey of 176,058 inpatients in our hospital and other city branches of our hospital over the past 3 years and obtained information concerning their use of humidified nasal cannulas for oxygen inhalation, nonhumidified nasal cannulas, anticoagulant and antiplatelet drugs, and oxygen inhalation flow rates. This information was compared with the data collected at consultation for epistaxis during these 3 years. <b><i>Results:</i></b> No significant difference was found between inpatients with humidified nasal cannulas and those without nasal cannula oxygen therapy in the incidence of consultations due to epistaxis (χ<sup>2</sup> = 1.007, <i>p</i> &#x3e; 0.05). The same trend was observed among hospitalized patients using anticoagulant and antiplatelet drugs (χ<sup>2</sup> = 2.082, <i>p</i> &#x3e; 0.05). Among the patients with an inhaled oxygen flow rate ≥5 L/min, the incidence of ear-nose-throat (ENT) consultations due to epistaxis was 0. No statistically significant difference was found between inpatients with a humidified oxygen inhalation flow rate &#x3c;5 L/min and those without nasal cannula oxygen therapy in the incidence of ENT consultations due to epistaxis (χ<sup>2</sup> = 0.838, <i>p</i> &#x3e; 0.05). A statistically significant difference was observed in the incidence of ENT consultations due to epistaxis between the low-flow nonhumidified nasal cannula and nonnasal cannula oxygen inhalation groups (χ<sup>2</sup> = 18.428, <i>p</i> &#x3c; 0.001). The same trend was observed between the 2 groups of low-flow humidified and low-flow nonhumidified nasal cannula oxygen inhalation (χ<sup>2</sup> = 26.194, <i>p</i> &#x3c; 0.001). <b><i>Discussion/Conclusion:</i></b> Neither high-flow humidified nasal cannula oxygen inhalation nor low-flow humidified nasal cannula oxygen inhalation will increase the incidence of recurrent or serious epistaxis complications; the same trend was observed for patients who use anticoagulant and antiplatelet drugs. Humidification during low-flow nasal cannula oxygen inhalation can prevent severe and repeated epistaxis to a certain extent.

Optimization of Inlet Ring Groove Arrangement for Suppression of Unstable Flow in a Centrifugal Impeller

2005 ◽  
Author(s):  
Masahiro Ishida ◽  
Daisaku Sakaguchi ◽  
Hironobu Ueki
Keyword(s):  
Flow Rate ◽  
The Other ◽  
Centrifugal Impeller ◽  
Shape Parameters ◽  
Unstable Flow ◽  
Ring Groove ◽  
Flow Rates ◽  
Small Flow ◽  
Specific Speed ◽  
Large Flow

An optimization of the inlet ring groove arrangement has been pursued in the present study for obtaining better impeller characteristics and a wider operation range at both small and large flow rates in a high specific speed type centrifugal impeller with inducer. The effects of the shape parameters with respect to the inlet ring groove on the impeller characteristic and the flow incidence were analyzed mainly based on numerical simulations, but also compared to the experimental results. At small flow rates, a significant improvement in the impeller characteristic is achieved due to reduction in the excessive-positive flow incidence by optimizing both location and width of the rear groove near the inducer tip throat. On the other hand, the impeller characteristic is improved at large flow rates by implementing the corner radius at the rear groove edge and by placing another front ring groove in the suction pipe. As a result, by the optimized configuration of the front and rear ring grooves, the unstable flow range of the test impeller can be reduced by about 50% without deterioration of the impeller characteristic even at the 125% flow rate.

Experimental Investigation of Pressure Fluctuations on Inner Wall of a Centrifugal Pump

2019 ◽  
Vol 36 (4) ◽  
pp. 401-410 ◽  
Author(s):  
Xiao-Qi Jia ◽  
Bao-Ling Cui ◽  
Zu-Chao Zhu ◽  
Yu-Liang Zhang
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Pressure Fluctuation ◽  
Pressure Fluctuations ◽  
High Flow ◽  
Low Flow ◽  
Centrifugal Pumps ◽  
Flow Rates ◽  
Pressure Distributions ◽  
Blade Passing Frequency

Abstract Affected by rotor–stator interaction and unstable inner flow, asymmetric pressure distributions and pressure fluctuations cannot be avoided in centrifugal pumps. To study the pressure distributions on volute and front casing walls, dynamic pressure tests are carried out on a centrifugal pump. Frequency spectrum analysis of pressure fluctuation is presented based on Fast Fourier transform and steady pressure distribution is obtained based on time-average method. The results show that amplitudes of pressure fluctuation and blade-passing frequency are sensitive to the flow rate. At low flow rates, high-pressure region and large pressure gradients near the volute tongue are observed, and the main factors contributing to the pressure fluctuation are fluctuations in blade-passing frequency and high-frequency fluctuations. By contrast, at high flow rates, fluctuations of rotating-frequency and low frequencies are the main contributors to pressure fluctuation. Moreover, at low flow rates, pressure near volute tongue increases rapidly at first and thereafter increases slowly, whereas at high flow rates, pressure decreases sharply. Asymmetries are observed in the pressure distributions on both volute and front casing walls. With increasing of flow rate, both asymmetries in the pressure distributions and magnitude of the pressure decrease.

scholarly journals Increased take-off level in automatic milking systems – effects on milk flow, milk yield and milking efficiency at the quarter level

2018 ◽  
Vol 86 (1) ◽  
pp. 85-87 ◽  
Author(s):  
Sabine Ferneborg ◽  
Måns Thulin ◽  
Sigrid Agenäs ◽  
Kerstin Svennersten-Sjaunja ◽  
Peter Krawczel ◽  
...  
Keyword(s):  
Flow Rate ◽  
The Other ◽  
Mean Flow ◽  
Flow Rates ◽  
Decline Phase ◽  
Flow Profiles ◽  
Milk Flow ◽  
Automatic Milking ◽  
Automatic Milking Systems ◽  
Time Required

AbstractThis research communication describes how different detachment levels (0.48, 0.3 and 0.06 kg milk/min) at the quarter-level affect milk flow profiles and overall milking efficiency in automatic milking systems. We hypothesized a higher detachment level would result in greater mean flow rates without affecting the volume of harvested milk per cow during 24 h compared to lower detachment levels. The data suggest milk flow decreased to a rate below the overmilking limit within the 6-s delay time required for termination in all treatments, but the duration of overmilking was shorter for the greatest detachment level compared to the other treatments. We conclude that setting a detachment level at a greater milk flow rate reduces the duration of overmilking without affecting the amount of milk harvested when applied to cows in mid-lactation during quarter-level milking. We also suggest that the steepness of the decline phase of the milk flow curve might have a larger effect than the actual detachment level on the duration of overmilking.

Effects of short blades on performance and inner flow characteristics of a low-specific-speed centrifugal pump

2017 ◽  
Vol 231 (4) ◽  
pp. 290-302 ◽  
Author(s):  
Can Kang ◽  
Ning Mao ◽  
Chen Pan ◽  
Yang Zhu ◽  
Bing Li
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Pressure Fluctuations ◽  
Flow Characteristics ◽  
Low Flow ◽  
Back Surface ◽  
Flow Rates ◽  
Pump Operation ◽  
Low Specific Speed ◽  
Specific Speed

A low-specific-speed centrifugal pump equipped with long and short blades is studied. Emphasis is placed on the pump performance and inner flow characteristics at low flow rates. Each short blade is intentionally shifted towards the back surface of the neighboring long blade, and the outlet parts of the short blades are uniformly shortened. Unsteady numerical simulation is conducted to disclose inner flow patterns associated with the modified design. Thereby, a comparison is enabled between the two schemes featured by different short blades. Both practical operation data and numerical results support that the deviation and cutting of the short blades can eliminate the positive slope of pump head curve at low flow rates. Therefore, the modification of short blades improves the pump operation stability. Due to the shortening of the outlet parts of the short blades, velocity distributions between impeller outlet and radial diffuser inlet exhibit explicitly altered circumferential flow periodicity. Pressure fluctuations in the radial diffuser are complex in terms of diversified periodicity and amplitudes. Flow rate influences pressure fluctuations in the radial diffuser considerably. As flow rate decreases, the regularity of the orbit of hydraulic loads exerted upon the impeller collapses while hydraulic loads exerted upon the short blades remain circumferentially periodic.

Cerebral Hyperperfusion Syndrome by the Numbers: Transient Focal Neurological Deficit, Imaging-Proven Focal Hyperperfusion, and High Graft Flow Rate Following Superficial Temporal Artery-Middle Cerebral Artery bypass in a Patient With Symptomatic Carotid Occlusion—Case Report

2018 ◽  
Vol 15 (6) ◽  
pp. E94-E99 ◽  
Author(s):  
Ralph Rahme ◽  
Tejaswi D Sudhakar ◽  
Marjan Alimi ◽  
Timothy G White ◽  
Rafael A Ortiz ◽  
...  
Keyword(s):  
Middle Cerebral Artery ◽  
Flow Rate ◽  
Perfusion Imaging ◽  
Superficial Temporal Artery ◽  
Temporal Artery ◽  
Low Flow ◽  
Flow Rates ◽  
Cerebral Hyperperfusion Syndrome ◽  
Cerebral Hyperperfusion ◽  
Graft Flow

Abstract BACKGROUND AND IMPORTANCE Cerebral hyperperfusion syndrome (CHS) is a well-known complication of superficial temporal artery (STA) to middle cerebral artery (MCA) bypass for ischemic cerebrovascular disease. While this argues against “low flow” in the bypass construct, flow rates in the graft have not been previously quantified in the setting of CHS. CLINICAL PRESENTATION A 58-yr-old man presented with recurrent left hemispheric ischemic strokes and fluctuating right hemiparesis and aphasia. Vascular imaging revealed left cervical internal carotid artery occlusion and perfusion imaging confirmed left hemispheric hypoperfusion. After failing to respond to maximal medical therapy, the patient underwent single-barrel STA-MCA bypass. Postoperatively, his symptoms resolved and blood pressure (BP) was strictly controlled within normal range. However, 2 d later, he developed severe expressive aphasia. CTA demonstrated a patent bypass graft and SPECT showed focal hyperperfusion in Broca's speech area. Seizure activity was ruled out. A high graft flow rate of 52 mL/min was documented by quantitative magnetic resonance angiography (MRA). Thus, the diagnosis of CHS was made and managed with strict BP control. The patient exhibited complete recovery of speech over a period of days and was discharged home. Repeat SPECT at 4 mo showed resolution of hyperperfusion and quantitative MRA demonstrated reduction of graft flow rate to 34 mL/min. CONCLUSION This is the first case of perfusion imaging-proven CHS after STA-MCA bypass, where high graft flow rates are objectively documented. Our observations constitute irrefutable evidence challenging the classic belief that the STA-MCA bypass is a low-flow construct.

Direct metabolic effects of isoproterenol and propranolol in ischemic myocardium of the dog

1980 ◽  
Vol 239 (4) ◽  
pp. H469-H469
Author(s):  
Michael Goodlett ◽  
Kyran Dowling ◽  
Lynne J. Eddy ◽  
James M. Downey
Keyword(s):  
High Energy ◽  
Ischemic Myocardium ◽  
The Other ◽  
Energy Utilization ◽  
Metabolic Effects ◽  
Low Flow ◽  
High Energy Phosphate ◽  
Drug Induced ◽  
Flow Rates ◽  
Induced Changes

The effect of either isoproterenol or propranolol on the metabolism of ischemic myocardium was examined. To ensure that all changes were due to changes in metabolism and not drug-induced changes in residual flow to the ischemic regions, we devised a preparation in which two coronary branches on the same heart were simultaneously perfused at a low flow rate. Microsphere measurements verified that the two ischemic regions were receiving identical blood flow rates. One branch received an infusion of 0.9% NaCl and the other received the drug. After 1 h both regions were biopsied and the high-energy phosphate levels in each region were determined. ATP and phosphocreatine each fell to about 50% of their starting values in the 0.9% NaCl-treated regions, and isoproterenol did not further depress the high-energy phosphate concentrations. Propranolol, on the other hand, significantly preserved the high-energy phosphate concentrations. We conclude that although isoproterenol seemed incapable of accelerating energy utilization in ischemic myocardium, propranolol is apparently capable of reducing it.

Interaction between CO2 concentration and flow rate on peripheral airway resistance

1991 ◽  
Vol 70 (6) ◽  
pp. 2514-2521 ◽  
Author(s):  
A. Kaise ◽  
A. N. Freed ◽  
W. Mitzner
Keyword(s):  
Flow Rate ◽  
Airway Resistance ◽  
Co2 Concentration ◽  
Low Flow ◽  
Flow Rates ◽  
Peripheral Airway ◽  
Residual Capacity ◽  
Local Ventilation ◽  
End Tidal ◽  
The Relationship

In the present study, we investigated the interaction between CO2 concentration and rate of delivered flow on peripheral airway resistance (Rp) in the intact canine lung. Dogs were anesthetized, intubated, paralyzed, and mechanically ventilated with room air to maintain end-tidal CO2 between 4.8 and 5.2%. Using a wedged bronchoscope technique, we measured Rp at functional residual capacity. The relationship between CO2 concentration and Rp was measured at flow rates of 100 and 400 ml/min with 5, 3, 2, 1, and 0% CO2 in air. Measurements were made at the end of a 3-min exposure to each gas. At low flow rates (100 ml/min) responses to hypocapnia were small, whereas at high flow rates (400 ml/min) responses were large. The PC50 (defined as the CO2 concentration required to produce a 50% increase in Rp above baseline Rp established on 5% CO2) at 400 ml/min (1.73%) was significantly larger than that at 100 ml/min (0.38%). We also directly measured the relationship between Rp and flow rate with 5% CO2 (normocapnia) or 1% CO2 (hypocapnia) delivered into the wedged segment. Increases in normocapnic flow caused small but significant decreases in Rp. In contrast, increases in hypocapnic flow from 100 to 400 ml/min caused a 108% increase in Rp. Thus the response to hypocapnia is augmented by increasing flow rate. This interaction can be explained by a simple model that considers the effect of local ventilation-perfusion ratio and gas mixing on the local CO2 concentration at the site of peripheral airway contraction.

Turbulence Measurements in a Centrifugal Pump With a Synchronously Orbiting Impeller

1991 ◽  
Author(s):  
Ronald D. Flack ◽  
Steven M. Miner ◽  
Ronald J. Beaudoin
Keyword(s):  
Centrifugal Pump ◽  
Reynolds Stress ◽  
Flow Rate ◽  
Cross Product ◽  
Design Flow ◽  
Low Flow ◽  
Rate Variation ◽  
Flow Rates ◽  
The Individual ◽  
Design Flow Rate

Turbulence profiles were measured in a centrifugal pump with an impeller with backswept blades using a two directional laser velocimeter. Data presented includes radial, tangential, and cross product Reynolds stresses. Blade to blade profiles were measured at four circumferential positions and four radii within and one radius outside the four bladed impeller. The pump was tested in two configurations; with the impeller running centered within the volute, and with the impeller orbiting with a synchronous motion (ε/r2 = 0.016). Flow rates ranged from 40% to 106% of the design flow rate. Variation in profiles among the individual passages in the orbiting impeller were found. For several regions the turbulence was isotropic so that the cross product Reynolds stress was low. At low flow rates the highest cross product Reynolds stress was near the exit. At near design conditions the lowest cross product stress was near the exit, where uniform flow was also observed. Also, near the exit of the impeller the highest turbulence levels were seen near the tongue. For the design flow rate, inlet turbulence intensities were typically 9% and exit turbulence intensities were 6%. For 40% flow capacity the values increased to 18% and 19%, respectively. Large local turbulence intensities correlated with separated regions. The synchronous orbit did not increase the random turbulence, but did affect the turbulence in the individual channels in a systematic pattern.

Suppression of Self-Excited Flow Instability in a Radial Diffuser Using Rough Surfaces

2006 ◽  
Author(s):  
Saad A. Ahemd ◽  
Hayder Salem
Keyword(s):  
Flow Rate ◽  
Smooth Surface ◽  
Flow Instability ◽  
Rough Surfaces ◽  
Flow Coefficient ◽  
Flow Instabilities ◽  
Low Flow ◽  
Flow Rates ◽  
Flow Limit ◽  
Stable Operating

Flow instabilities in a compression system at low flow rates set the flow limit of the stable operating range. Experiments to investigate the feasibility of controlling the stall in the radial diffuser of a low speed centrifugal compressor were carried out. The technique was very simple and involved using rough surfaces (i.e., sand papers) attached to the diffuser shroud. The results showed that the flow instability in the diffuser (stall) was delayed to a lower flow coefficient (the mass flow rate could be reduced to 70% of its value with the smooth surface) when the rough surfaces were positioned on the diffuser shroud.

Sign in / Sign up

Export Citation Format

Share Document