Gain enhancement of wideband circularly polarized antenna using FSS

2016 ◽  
Vol 9 (3) ◽  
pp. 697-703 ◽  
Author(s):  
Nagendra Kushwaha ◽  
Raj Kumar
Keyword(s):  
Coplanar Waveguide ◽  
Axial Ratio ◽  
Frequency Selective Surface ◽  
High Gain ◽  
Unit Element ◽  
Impedance Bandwidth ◽  
Circularly Polarized ◽  
Gain Enhancement ◽  
Antenna Performance ◽  
Measured Impedance

This paper presents a high gain, wideband circularly polarized (CP) antenna. High gain of the antenna is achieved by employing a frequency selective surface (FSS) as a reflector. The antenna is a coplanar waveguide-fed structure with a modified L-shaped radiating patch. The unit element of the FSS is formed by connecting two modified dipoles at an angle of 90°. The antenna with reflector has a measured impedance bandwidth of 74.3% (2.2–4.8 GHz) and a 3-dB axial ratio bandwidth (ARBW) of 62% (2.2–4.18 GHz). The maximum boresight gain of the proposed antenna with reflector is 7.1 dB at 3.4 GHz. The radiation patterns of the antenna with the FSS are also measured and compared with simulated patterns. The various aspects of effect of FSS on CP antenna performance are also discussed.

Wideband low-profile aperture-coupled circularly polarized antenna based on metasurface

2018 ◽  
Vol 10 (7) ◽  
pp. 851-859 ◽  
Author(s):  
Qi Zheng ◽  
Chenjiang Guo ◽  
Jun Ding
Keyword(s):  
Coplanar Waveguide ◽  
Axial Ratio ◽  
High Gain ◽  
Mode Analysis ◽  
Impedance Bandwidth ◽  
Equivalent Circuit Analysis ◽  
Circularly Polarized ◽  
Low Profile ◽  
Compact Size ◽  
Feeding Structure

AbstractIn this paper, a metasurface-based aperture-coupled circularly polarized (CP) antenna with wideband and high radiation gain is proposed and analyzed. The proposed antenna is comprised of coplanar waveguide coupling with 4 × 4 corner truncated square patches, which show compact size and low profile. The mechanism of the CP antenna is analyzed theoretically based on the mode analysis and equivalent circuit analysis. The parameters of feeding structure and truncated corner are studied and optimized to achieve wide impedance bandwidth (BW) and axial ratio (AR) BW. Finally, an overall size of 38.8 mm × 38.8 mm × 3.5 mm (0.71λ0 × 0.71λ0 × 0.064λ0 at 5.5 GHz) CP antenna is proposed and fabricated. The simulated results demonstrate that over 41.7% impedance BW (S11 < −10 dB) of 4.55–6.95 GHz and 3 dB AR BW of 5.05–6.15 GHz (fractional BW is about 19.6%) are achieved. In addition, the antenna yielded a broadside CP radiation with a high gain average about 7.5 dBic. Experimental results are in good agreement with the simulated ones.

A high gain wideband circularly polarized microstrip antenna

2020 ◽  
Vol 12 (7) ◽  
pp. 678-687
Author(s):  
Arun Kumar ◽  
Santanu Dwari ◽  
Ganga Prasad Pandey ◽  
Binod Kumar Kanaujia ◽  
Dinesh Kumar Singh
Keyword(s):  
Microstrip Antenna ◽  
Axial Ratio ◽  
High Gain ◽  
Split Ring Resonator ◽  
Impedance Bandwidth ◽  
Reflected Waves ◽  
Circularly Polarized ◽  
Gain Enhancement ◽  
Reflector Surface ◽  
Printed Monopole Antenna

AbstractIn this paper, a high gain wideband circularly polarized (CP) microstrip antenna is presented for broadband operation. The proposed structure comprised of a partially grounded printed monopole antenna loaded with a split ring resonator and a metallic reflector. By using the metallic reflector surface underneath the patch radiator results in the reflected waves in the same phase with main lobe radiation, thereby improving the gain and it also acts like a secondary radiator to generate wideband CP behavior in the proposed design. A gain enhancement of 4.3 dBi is achieved in the operating frequency band as compared with the design without a metallic reflector. The maximum gain achieved in the presented method is 8.6 dBic over the entire operating range. The proposed design shows a wideband behavior ranging from 4.30 to 9.10 GHz with the 10-dB impedance bandwidth of 71.64%. In addition, the proposed design yielded a broadside right hand CP radiation with a 3-dB axial ratio bandwidth of 33.88% from 4.98 to 7.01 GHz. The proposed antenna is fabricated and experimental results on reflection coefficient, gain, axial ratio, and radiation patterns concede well with simulation results.

scholarly journals High-Gain Waveguide-Fed Circularly Polarized Spidron Fractal Aperture Antenna

2019 ◽  
Vol 9 (4) ◽  
pp. 691 ◽  
Author(s):  
Son Trinh-Van ◽  
Thuy Thi ◽  
Youngoo Yang ◽  
Kang-Yoon Lee ◽  
Kyung-Young Jung ◽  
...  
Keyword(s):  
Rectangular Waveguide ◽  
Fractal Structure ◽  
Ground Plane ◽  
Axial Ratio ◽  
Dielectric Substrate ◽  
High Gain ◽  
Impedance Bandwidth ◽  
Aperture Antenna ◽  
Circularly Polarized ◽  
Measured Impedance

A high-gain rectangular waveguide-fed aperture antenna that uses a Spidron fractal structure to produce circular polarization is proposed. The antenna consists of a Spidron fractal aperture etched onto the ground plane of a dielectric substrate that is directly excited by a WR (Waveguide Rectangular)-90 waveguide-to-coax adapter. A superstrate was implemented at an appropriate distance above the antenna to enhance the broadside gain significantly. An antenna prototype was fabricated and tested to validate the design. The measured impedance bandwidth for | S 11 | ≤ −10 dB is 9.89–11.58 GHz (15.74%). The corresponding measured 3 dB axial ratio (AR) bandwidth is 10.68–11.00 GHz (2.95%), and within the measured 3 dB AR bandwidth, a maximum realized gain of 9.59 dBic is achieved. The radiation patterns of the proposed antenna are presented and discussed.

scholarly journals CPW-fed circularly-polarized antenna array with high front-to-back ratio and low-profile

Open Physics ◽  
2018 ◽  
Vol 16 (1) ◽  
pp. 651-655 ◽  
Author(s):  
Yilin Liu ◽  
Kama Huang
Keyword(s):  
Antenna Array ◽  
Coplanar Waveguide ◽  
Ground Plane ◽  
Axial Ratio ◽  
Antenna Design ◽  
Impedance Bandwidth ◽  
Feeding Method ◽  
Circularly Polarized ◽  
Low Profile ◽  
Novel Design

Abstract A novel design of a coplanar waveguide (CPW) feed antenna array with circular polarization (CP) and a high front-to-back ratio is described. The proposed CP array is achieved by using a compact CPW–slotline transition network etched in the ground plane. The measured results show that this kind of feeding method can improve the impedance bandwidth, as well as the axial ratio bandwidth of the CP antenna array and provide adequate gain. The proposed array can achieve a 6.08% impedance bandwidth and a 4.10% CP bandwidth. Details of the antenna design and experimental results are presented and discussed.

scholarly journals A Circularly Polarized Antenna Array with Gain Enhancement for Long-Range UHF RFID Systems

Electronics ◽  
2019 ◽  
Vol 8 (4) ◽  
pp. 400 ◽  
Author(s):  
Wei Hu ◽  
Guangjun Wen ◽  
Daniele Inserra ◽  
Yongjun Huang ◽  
Jian Li ◽  
...  
Keyword(s):  
Antenna Array ◽  
Long Range ◽  
Radio Frequency Identification ◽  
Coaxial Line ◽  
Axial Ratio ◽  
High Gain ◽  
Basic Element ◽  
Uhf Rfid ◽  
Circularly Polarized ◽  
Gain Enhancement

A 2 × 2 circularly polarized (CP) sequential rotation microstrip patch antenna array with high gain for long-range ultra-high frequency (UHF) radio frequency identification (RFID) communication is proposed in this paper. In order to meet the operational frequency band requirement of 840–960 MHz and, at the same time, achieve enhanced broadside gain, a two-level sequential rotation structure is developed. Series power divider is used as the basic element of the feed network that is implemented with the substrate-integrated coaxial line technology for minimizing radiation losses. The manufactured prototype exhibits a peak gain of 12.5 dBic at 900 MHz and an axial ratio (AR) bandwidth (AR ≤ 3 dB) of 18.2% from 828 to 994 MHz. In comparison with the state-of-the-art, the proposed antenna shows an excellent gain/size trade-off.

scholarly journals Design of a Substrate-Integrated Fabry-Pérot Cavity Antenna forK-Band Applications

2015 ◽  
Vol 2015 ◽  
pp. 1-12 ◽  
Author(s):  
Truong Khang Nguyen ◽  
Ikmo Park
Keyword(s):  
Coplanar Waveguide ◽  
Ground Plane ◽  
Cost Effective ◽  
Frequency Selective Surface ◽  
High Gain ◽  
Hole Array ◽  
Impedance Bandwidth ◽  
Low Profile ◽  
Fabry Perot ◽  
Feeding Structure

This paper presents the design of a planar, low-profile, high-gain, substrate-integrated Fabry-Pérot cavity antenna forK-band applications. The antenna consists of a frequency selective surface (FSS) and a planar feeding structure, which are both lithographically patterned on a high-permittivity substrate. The FSS is made of a circular hole array that acts as a partially reflecting mirror. The planar feeding structure is a wideband leaky-wave slit dipole fed by a coplanar waveguide whose ground plane acts as a perfect reflective mirror. The measured results show that the proposed antenna has an impedance bandwidth of more than 8% (VSWR ≤ 2), a maximum gain of 13.1 dBi, and a 3 dB gain bandwidth of approximately 1.3% at a resonance frequency of around 21.6 GHz. The proposed antenna features low-profile, easy integration into circuit boards, mechanical robustness, and excellent cost-effective mass production suitability.

scholarly journals A Single-Point-Fed Wideband Circularly Polarized Rectangular Dielectric Resonator Antenna

2016 ◽  
Vol 2016 ◽  
pp. 1-9
Author(s):  
Deqiang Yang ◽  
Meng Zou ◽  
Jin Pan
Keyword(s):  
Dielectric Resonator ◽  
Single Point ◽  
Axial Ratio ◽  
Design Concept ◽  
Impedance Bandwidth ◽  
Dielectric Resonator Antenna ◽  
Circularly Polarized ◽  
Measured Impedance ◽  
Rectangular Dielectric Resonator Antenna ◽  
Good Agreement

A single-point-fed circularly polarized (CP) rectangular dielectric resonator antenna (DRA) with wide CP bandwidth is presented. By usingTE111andTE113modes of the rectangular DRA, a wideband CP performance is achieved. The coupling slot of the antenna contains a resistor loaded monofilar-spiral-slot and four linear slots. Design concept of the proposed antenna is demonstrated by simulations, and parameter studies are carried out. Prototype of the proposed antenna was fabricated and measured. Good agreement between the simulation and measurement is obtained. The measured impedance bandwidth (|S11|<-10 dB) and 3 dB axial-ratio (AR) bandwidth are 51.4% (1.91–3.23 GHz) and 33.0% (2.15–3.00 GHz), respectively.

scholarly journals High-Gain Circularly-Polarized Elliptically-Annular Antenna-Array with Reduced Side-Lobe Level

2020 ◽  
Vol 9 (4) ◽  
pp. 2319-2325
Keyword(s):  
Circular Polarization ◽  
Antenna Array ◽  
Satellite Communication ◽  
Axial Ratio ◽  
Side Lobe ◽  
High Gain ◽  
Side Lobe Level ◽  
Single Element ◽  
Circularly Polarized ◽  
Gain Enhancement

A single feed microstrip patch elliptically annular antenna array has been proposed for high gain circularly polarized (CP) radiation. An array of elliptically annular patches antenna resonates at a frequency of 3.77 GHz which can be used in satellite communication and radar application. A corporate feed network with quarter-wave transformer has been used for uniform excitation of all the array elements. Thus a good circular polarization is obtained by using a single feed with enhanced gain 15.62 dB compared to single patch. The radiation pattern, axial ratio and input impedance of the proposed elliptically annular antenna array is compared with single element elliptically annular antenna. A substantial gain enhancement with low side lobe level (SLL) is observed keeping circular polarization intact. Further, simulated and measured results of the proposed antenna array have been compared and found that axial ratio and gain are in good agreement.

A Compact CPW Fed Wideband Slot Antenna for Wireless Communications

2020 ◽  
pp. 2050184
Author(s):  
Amrita Gorai ◽  
Bappadittya Roy ◽  
G. K. Mahanti
Keyword(s):  
Wireless Communications ◽  
Coplanar Waveguide ◽  
Axial Ratio ◽  
Slot Antenna ◽  
Impedance Bandwidth ◽  
Fractional Bandwidth ◽  
Ieee 802.11A ◽  
Circularly Polarized ◽  
Wireless Applications ◽  
Simulation Results

A compact circularly polarized CPW-fed slot antenna is proposed here. The antenna consists of a pentagonal patch within an asymmetrical slot with a single coplanar waveguide feed. The proposed antenna is excited with CPW feed mechanism and investigated experimentally. The structure is fabricated on FR4 epoxy substrate with a permittivity of 4.4. The impedance bandwidth of 10[Formula: see text]GHz (4[Formula: see text]GHz to 14[Formula: see text]GHz) and the axial ratio bandwidth of 1.2[Formula: see text]GHz with the corresponding fractional bandwidth of 113%. The simulation results fulfil the bandwidth requirements of IEEE 802.11a (5.15–5.35[Formula: see text]GHz/5.47–5.725[Formula: see text]GHz) for wireless applications. In terms of bandwidth, compactness and circular polarization comparable results between simulated and measured results clearly show the validity of the proposed structure.

Slot loaded EBG-based metasurface for performance improvement of circularly polarized antenna for WiMAX applications

2019 ◽  
Vol 12 (3) ◽  
pp. 212-220 ◽  
Author(s):  
Alka Verma ◽  
Anil Kumar Singh ◽  
Neelam Srivastava ◽  
Shilpee Patil ◽  
Binod Kumar Kanaujia
Keyword(s):  
Performance Improvement ◽  
Coplanar Waveguide ◽  
Axial Ratio ◽  
Impedance Bandwidth ◽  
Compact Structure ◽  
Circularly Polarized ◽  
Feed Line ◽  
Rectangular Patch ◽  
Low Profile ◽  
Good Agreement

AbstractIn this paper, an electromagnetic band gap (EBG) metasurface (MS) superstrate-based circularly polarized antenna for the WiMAX (3.5 GHz) band is proposed. The proposed structure comprises a 2 × 2 slot-loaded rectangular patch MS array that can be perceived as a polarization-dependent EBG MS superstrate. Furthermore, to achieve circular polarization, the proposed antenna has an inclined coupling slot onto the ground with a conventional coplanar waveguide feed line. The proposed antenna has a compact structure with a low profile of 0.037λ0 (λ0 stands for the free-space wavelength at 3.48 GHz) and a ground size of 30 × 30 mm2. The measured results show that the −10 dB impedance bandwidth for the proposed antenna is 34.6% and the 3-dB axial ratio (AR) bandwidth is 6.8% with a peak gain of 3.91 dBi in the desired operating band. Good agreement between the simulated and the measured results verifies the performance of the proposed antenna.

Sign in / Sign up

Export Citation Format

Share Document