scholarly journals Electric polarization properties of BaTiO3-BiFeO3 as nanomultiferroic material produced by sol-gel method

2018 ◽  
Vol 204 ◽  
pp. 05005 ◽  
Author(s):  
Dwita Suastiyanti ◽  
Maykel T.E. Manawan ◽  
Marlin Wijaya
Keyword(s):  
Particle Size ◽  
Sol Gel ◽  
Sinter Time ◽  
Weight Ratio ◽  
Electric Polarization ◽  
X Ray Diffraction ◽  
Gel Method ◽  
Sol Gel Method ◽  
Particle Size Analyzer ◽  
Dominant Phase

The nanomultiferroic material which is synthesized in this research used sol-gel method. The research used weight ratio of BaTiO3: BiFeO3 of 2: 1. Gel formed after heating at 80-90°C was calcined at 350°C for 4 hours and then sintered at 700,750 and 800°C for 2, 4 and 6 hours respectively. Powder produced after sintering was characterized by X-Ray Diffraction (XRD) test using XRD Phillips PW 1835 type, 20°-100° diffraction angle and CuKα, electric polarization properties test and particle size measurement using Particle Size Analyzer of Beckman Coulter DelsaTM Nano instrument. From the characterization results, it is obtained that the dominant phase is Barium Bismuth Iron (III) Oxide (BaBiFe2O5). Electrical polarization properties such as remanent, coersivity and saturation reach maximum value at sinter temperature of 750° C and sinter time of 6 hours. This result is supported by the smallest particle size of powder (54-57 nm) and also supported by the largest number of dominant phase (98.79%) at same condition.

scholarly journals Synthesis of Spherical Silica by Sol-Gel Method and Its Application as Catalyst Support

2011 ◽  
Vol 10 (2) ◽  
pp. 25
Author(s):  
Anirut Leksomboon ◽  
Bunjerd Jongsomjit
Keyword(s):  
Particle Size ◽  
Ethylene Glycol ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Sol Gel ◽  
Weight Ratio ◽  
Gel Method ◽  
Sol Gel Method ◽  
Spherical Silica

In this present study, the spherical silica support was synthesized from tetraethyloxysilane (TEOS), water, sodium hydroxide, ethylene glycol and n-dodecyltrimethyl ammonium bromide (C12TMABr). The particle size was controlled by variation of the ethylene glycol co-solvent weight ratio of a sol-gel method preparation in the range of 0.10 to 0.50. In addition, the particle size apparently increases with high weight ratio of co-solvent, but the particle size distribution was broader. The standard deviation of particle diameter is large when the co-solvent weight ratio is more than 0.35 and less than 0.15. However, the specific surface area was similar for all weight ratios ranging from 1000 to 1300 m2/g. The synthesized silica was spherical and has high specific surface area. The cobalt was impregnated onto the obtained silica to produce the cobalt catalyst used for CO2 hydrogenation.</

scholarly journals Size Effects on Magnetic Properties ofNi0.5Zn0.5Fe2O4Prepared by Sol-Gel Method

2013 ◽  
Vol 2013 ◽  
pp. 1-10 ◽  
Author(s):  
Min Zhang ◽  
Zhenfa Zi ◽  
Qiangchun Liu ◽  
Peng Zhang ◽  
Xianwu Tang ◽  
...  
Keyword(s):  
Particle Size ◽  
Magnetic Measurements ◽  
Sol Gel ◽  
Domain Wall Motion ◽  
Blocking Temperature ◽  
Particle Sizes ◽  
X Ray Diffraction ◽  
Gel Method ◽  
Sol Gel Method ◽  
Cation Redistribution

Ni0.5Zn0.5Fe2O4particles with different particle sizes have been synthesized by sol-gel method. X-ray diffraction results show that all the samples are pure cubic spinel structure with their sizes ranging from 9 to 96 nm. The lattice constant significantly decreases with further increasing annealing temperature. The magnetic measurements show superparamagnetic nature below the particle size of 30 nm, while others show ferrimagnetic nature above the corresponding blocking temperature. The blocking temperature increases with the increase in particle size, which can be explained by Stoner-Wohlfarth theory. The saturation magnetization increases as the particle size increases, which can be explained by the cation redistribution on tetrahedral A and octahedral B sites and the domain wall motion. The variation of coercivity as a function of particle size is based on the domain structure.

Preparation and Photoluminescence Properties of RE-Doped GaN Film by Sol-Gel Method

2016 ◽  
Vol 680 ◽  
pp. 515-519 ◽  
Author(s):  
Xue Wen Wang ◽  
Chan Liu ◽  
Cheng Xing Wang
Keyword(s):  
Particle Size ◽  
Sol Gel ◽  
Hexagonal Wurtzite Structure ◽  
X Ray Diffraction ◽  
Inhibitory Effects ◽  
Blue Band ◽  
Gel Method ◽  
Sol Gel Method ◽  
Good Crystallinity ◽  
Gan Film

This paper fabricates rare earth(RE) La, Ce and Pr doped GaN film by sol-gel method and uses X-ray diffraction analysis (XRD), scanning electron microscopy (SEM) and photoluminescence spectroscopy (PL) to characterize and analyze their dimensions, morphology and optical properties. The results show that doped GaN film is hexagonal wurtzite structure and has good crystallinity. With the increasing of the Ce doping amounts, the particle size of GaN increases gradually. While augmenting the doping amounts of La or Ce can cause particle size to be smaller. Several RE doped GaN have inhibitory effects on yellow luminescence and generate red emission peaks. The GaN:La don’t appear photoluminescence peak except for the characteristic peak of GaN. Ce doped GaN appear emission peaks with narrow FWHM between 500~600nm. 5% Pr doping enhances the intrinsic excitation and blue band edge luminescence of GaN. Through the analysis, it can be found that La, Ce and Pr doping influence the grain growth and photoluminescence spectrum of GaN film effectively.

Influence of Calcining Atmosphere on Synthesis of Mixed Conducting Oxides SrFeCo0.5Oy by Citrates Sol-Gel Method

2011 ◽  
Vol 391-392 ◽  
pp. 1205-1209
Author(s):  
Qing Yang Du ◽  
Hui Jun Xu
Keyword(s):  
Bulk Density ◽  
Sol Gel ◽  
Synthesis Process ◽  
X Ray Diffraction ◽  
Gel Method ◽  
X Ray ◽  
Sol Gel Method ◽  
Conducting Oxides ◽  
Structure And Morphology ◽  
Dominant Phase

Mixed conducting oxides SrFeCo0.5Oy was synthesized by citrates sol-gel method. The effect of calcining atmosphere on synthesis process of samples was studied. The crystal structure and morphology of calcined powders were characterized by X-ray diffraction(XRD) and scanning electron microscopy(SEM) and the bulk density of sintered samples was determined by Archimedes method. The experimental results showed that the dominant phase perovskite Sr-Fe-Co-O oxides was prepared by calcining in oxygen. The powder obtained had flake shape and the particle was smaller. The dominant phase orthorhombic Sr-Fe-Co-O oxides was prepared by calcining in argon. The powder obtained had sphere shape and the particle was bigger. The bulk density of samples sintered at low temperature in oxygen was smaller than that of in argon. The reaction mechanism of samples calcined in different atmosphere was also discussed.

Preparation of Titanium Dioxide Sol and its Application on Tussah Silk Fixation with Vegetable Dye

2013 ◽  
Vol 821-822 ◽  
pp. 618-621
Author(s):  
Yan Hua Lu ◽  
Ming Su Song ◽  
Jie Lin
Keyword(s):  
Particle Size ◽  
Titanium Dioxide ◽  
Sol Gel ◽  
Average Diameter ◽  
Tetrabutyl Titanate ◽  
Test Results ◽  
Gel Method ◽  
Sol Gel Method ◽  
Washing Fastness ◽  
Particle Size Analyzer

In this paper, nanosol of titanium dioxide was prepared by sol-gel method using tetrabutyl-titanate as a precursor. The Particle Size Analyzer test results showed that the average diameter of the particles was less than 10 nm, and most particle size ranged from 6nm to 16nm. The prepared mechanism was discussed and then applied to fixation of vegetable turmeric dyed tussah silk. The fixation results indicated that the rubber fastness and washing fastness increased remarkably and the K/S values changed a little.

Annealing Effects on the Physical and Magnetic Properties of Tb1.5Y1.5Fe5O12 Films Nanoparticles Prepared by Sol-Gel Method

2013 ◽  
Vol 756 ◽  
pp. 91-98 ◽  
Author(s):  
Ftema W. Aldbea ◽  
Noor Bahyah Ibrahim ◽  
Mustafa Hj. Abdullah
Keyword(s):  
Particle Size ◽  
Magnetic Properties ◽  
Annealing Temperature ◽  
Quartz Substrate ◽  
Sol Gel ◽  
Lattice Parameter ◽  
Gel Method ◽  
X Ray ◽  
Sol Gel Method ◽  
Iron Garnet

Terbium –substituted yttrium iron garnet (Tb1.5Y1.5Fe5O12) films nanoparticles were successfully prepared by a sol-gel method. The films were deposited on the quartz substrate using spin coating technique. To study effect of annealing temperature, the annealing process was executed at 700, 800 and 900 °C in air for 2 hours. The X-ray diffraction (XRD) proved that the pure phase of garnet structure was detected for the film annealed at 900 °C. The lattice parameter increased with the increment of annealing temperature and the highest value of 12.35 Å was obtained at 900 °C. Field Emission Scanning Electron Microscope (FE-SEM) results showed that the particle size increased from 43nm to 56nm as annealing temperature increased from 700 to 900°C. The film’s thickness also affected by increasing of annealing temperature and become thin at 900 °C due to densification process occurred at high annealing temperature. The elemental compositions of the Tb1.5Y1.5Fe5O12 film were detected using an Energy Dispersive X-raySpectroscopy (EDX). Magnetic properties at room temperature were measured using a Vibrating Sample Magnetometer (VSM).The saturation magnetization Ms increased with the annealingtemperature and showed a high value of 104emu/cm3, but the coercivity Hc of the film was decreased due to the increment of the particle size. Normal 0 21 false false false MS X-NONE X-NONE MicrosoftInternetExplorer4 Terbium –substituted yttrium iron garnet (Tb1.5Y1.5Fe5O12) films nanoparticles were successfully prepared by a sol-gel method. The films were deposited on the quartz substrate using spin coating technique. To study effect of annealing temperature, the annealing process was executed at 700, 800 and 900°C in air for 2 hours. The X-ray diffraction (XRD) proved that the pure phase of garnet structure was detected for the film annealed at 900 °C. The lattice parameter increased with the increment of annealing temperature and the highest value of 12.35 Å was obtained at 900 °C. Field Emission Scanning Electron Microscope (FE-SEM) results showed that the particle size increased from 43nm to 56nm as annealing temperature increased from 700 to 900 °C. The film’s thickness also affected by increasing of annealing temperature and become thin at 900 °C due to densification process occurred at high annealing temperature. The elemental compositions of the Tb1.5Y1.5Fe5O12 film were detected using an Energy Dispersive X-ray Spectroscopy (EDX). Magnetic properties at room temperature were measured using a Vibrating Sample Magnetometer (VSM).The saturation magnetization Ms increased with the annealing temperature and showed a high value of 104emu/cm3, but the coercivity Hc of the film was decreased due to the increment of the particle size. st1\:*{behavior:url(#ieooui) } /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;}

Impedance Spectroscopy Study of LiTaO3 Powder Synthesized via Sol-Gel Method

2012 ◽  
Vol 545 ◽  
pp. 275-278 ◽  
Author(s):  
Lili Widarti Zainuddin ◽  
Norlida Kamarulzaman
Keyword(s):  
Room Temperature ◽  
Single Phase ◽  
Sol Gel ◽  
Rhombohedral Structure ◽  
Spectroscopy Study ◽  
X Ray Diffraction ◽  
Gel Method ◽  
X Ray ◽  
Sol Gel Method ◽  
Impedance Spectroscopy Study

A ceramics sample of LiTaO3 was prepared using a sol-gel method. The sample is annealed at 750 °C for 48 hours. X-ray diffraction analysis indicate the formation of single phase, rhombohedral structure. An ac impedance study was used to analyse the conductivity of LiTaO3 at room temperature and at various temperatures.

Magnetic Properties of Bulk Zn0.95-XMnXFe0.05O2 Prepared by Sol-Gel Method and Subsequent Hot Pressing

2011 ◽  
Vol 268-270 ◽  
pp. 356-359 ◽  
Author(s):  
Wen Song Lin ◽  
C. H. Wen ◽  
Liang He
Keyword(s):  
Magnetic Properties ◽  
Photoelectron Spectroscopy ◽  
Raw Materials ◽  
Sol Gel ◽  
Secondary Phase ◽  
X Ray Diffraction ◽  
Gel Method ◽  
X Ray ◽  
Sol Gel Method ◽  
Doped Zno

Mn, Fe doped ZnO powders (Zn0.95-xMnxFe0.05O2, x≤0.05) were synthesized by an ameliorated sol-gel method, using Zn(CH3COO)2, Mn(CH3COO)2and FeCl2as the raw materials, with the addition of vitamin C as a kind of chemical reducer. The resulting powder was subsequently compacted under pressure of 10 MPa at the temperature of 873K in vacuum. The crystal structure and magnetic properties of Zn0.95-xMnxFe0.05O2powder and bulk samples have been investigated by X-ray diffraction (XRD) and vibrating sample magnetometer (VSM). X-ray photoelectron spectroscopy (XPS) was used to study chemical valence of manganese, iron and zinc in the samples. The x-ray diffraction (XRD) results showed that Zn0.95-xMnxFe0.05O (x≤0.05) samples were single phase with the ZnO-like wurtzite structure. No secondary phase was found in the XRD spectrum. X-ray photoelectron spectroscopy (XPS) showed that Fe and Mn existed in Zn0.95-xMnxFe0.05O2samples in Fe2+and Mn2+states. The results of VSM experiment proved the room temperature ferromagnetic properties (RTFP) of Mn, Fe co-doped ZnO samples.

Fast response acetone-sensing properties of SnO2 nanoparticles prepared by the sol-gel method

2021 ◽  
Vol 93 (3) ◽  
pp. 30401
Author(s):  
Jiaxing Wang ◽  
Hai Yu ◽  
Yong Zhang
Keyword(s):  
High Performance ◽  
Gas Sensing ◽  
Sno2 Nanoparticles ◽  
Sol Gel ◽  
Fast Response ◽  
X Ray Diffraction ◽  
Gel Method ◽  
Sol Gel Method ◽  
Short Recovery Time ◽  
Acetone Gas Detection

SnO2 nanoparticle architectures were successfully synthesized using a sol-gel method and developed for acetone gas detection. The morphology and structure of the particles were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The SnO2 nanoparticle architectures were configured as high-performance sensors to detect acetone and showed a very fast response time (<1 s), a short recovery time (10 s), good repeatability and high selectivity at a relatively low working temperature. Thus, SnO2 nanoparticles should be promising candidates for designing and fabricating acetone gas sensors with good gas sensing performance. The possible gas sensing mechanism is also presented.

scholarly journals Effect of Preheating Temperature on Synthesis of Pure BiFeO3 via Sol–Gel Method

Nanopages ◽  
2019 ◽  
pp. 1-11
Author(s):  
G. M. Taha ◽  
M. N. Rashed ◽  
M. S. El-Sadek ◽  
M. A. Moghazy
Keyword(s):  
Electron Microscope ◽  
Transmission Electron Microscope ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Pure Bifeo3 ◽  
Gel Method ◽  
X Ray ◽  
Sol Gel Method ◽  
Transmission Electron ◽  
Preheating Temperature

Abstract BiFeO3 (BFO) nanopowder was synthesized in a pure form via a sol- gel method based on glycol gel reaction. Effect of drying and preheating temperature on preventing other phases was studied. Many parameters were studied as calcination temperature and time & stirring temperature as well. The prepared powder was characterized by X-Ray Diffraction of powder (XRD) and Transmission Electron Microscope (TEM). High pure BiFeO3 was obtained by preheated process at 400 °C for 0.5 h and calcination at 600 °C for 0.5 h without any impurities compared to dry at110 °C.

Sign in / Sign up

Export Citation Format

Share Document