Elastoplastic Buckling of Anisotropic Aluminum Plate Elements

1998 ◽  
Vol 124 (6) ◽  
pp. 712-719 ◽  
Author(s):  
L. A. Moen ◽  
M. Langseth ◽  
O. S. Hopperstad
Keyword(s):  
Aluminum Plate ◽  
Plate Elements

Формирование изображений электрических сигналов преобразователя магнитного поля при гистерезисной интерференции для контроля металлов в импульсных магнитных полях

2020 ◽  
pp. 38-45
Author(s):  
В.В. Павлюченко ◽  
Е.С. Дорошевич
Keyword(s):  
Magnetic Field ◽  
Aluminum Plate ◽  
Thickness Variation ◽  
Magnetic Carrier ◽  
Electric Voltage ◽  
Total Strength ◽  
Magnetic Field Transducer ◽  
The Given ◽  
The Magnetic Field

Based on the developed methods of hysteresis interference, the calculated dependences U(x) of the electric voltage taken from the magnetic field transducer on the x coordinate were obtained. A magnetic carrier with an arctangent characteristic was exposed to a series of bipolar pulses of the magnetic field of a linear inductor of one, two, three, four, five and fifteen pulses. An algorithm is presented for the sequence of changes in the magnitude of the total strength of the magnetic field pulses on the surface of an aluminum plate, which provides the same amplitude of hysteresis oscillations of the electric voltage and makes it possible to obtain a linear difference dependence U(x) for wedge-shaped and flat aluminum samples. The results obtained make it possible to increase the accuracy and efficiency of control of the thickness of the object and its thickness variation in the given directions, as well as the defects of the object.

Delamination of Laminate Plates

2014 ◽  
Vol 969 ◽  
pp. 97-100 ◽  
Author(s):  
Eva Kormaníková
Keyword(s):  
Finite Element Analysis ◽  
Mixed Mode ◽  
Plate Theory ◽  
Laminate Plate ◽  
Element Analysis ◽  
Interface Elements ◽  
First Order ◽  
Plate Elements ◽  
Interface Modeling ◽  
Shear Deformable

The paper deals with numerical modeling of delamination of laminate plate consists of unidirectional fiber reinforced layers. The methodology adopts the first-order shear laminate plate theory and fracture and contact mechanics. There are described sublaminate modeling and delamination modeling by the help of finite element analysis. With the interface modeling there is calculated the energy release rate along the lamination front. Numerical results are given for mixed mode delamination problems by implementing the method in a 2D finite analysis, which utilizes shear deformable plate elements and interface elements. Numerical example is done by the commercial ANSYS code.

Design and Implementation of the Cold-Rolled Aluminum Plate Surface On-Line Defect Detection System

2013 ◽  
Vol 712-715 ◽  
pp. 2323-2326
Author(s):  
Xing Guang Qi ◽  
Hai Lun Zhang ◽  
Xiao Ting Li
Keyword(s):  
High Speed ◽  
Surface Defects ◽  
Detection System ◽  
Aluminum Plate ◽  
Gigabit Ethernet ◽  
Accurate Detection ◽  
High Processing Speed ◽  
Rolled Aluminum ◽  
On Line ◽  
Cold Rolled

This paper presents an on-line surface defects detection system based on machine vision, which has high speed architecture and can perform high accurate detection for cold-rolled aluminum plate. The system consists of high speed camera and industrial personal computer (IPC) array which connected through Gigabit Ethernet, achieved seamless detection by redundant control. In order to acquire high processing speed, single IPC as processor receives from and deals with only one or two cameras' image. Experimental results show that the system with high accurate detection capability can satisfy the requirement of real time detection and find out the defects on the production line effectively.

Sign in / Sign up

Export Citation Format

Share Document