Prediction of Critical Heat Flux in Annular Flow Using a Film Flow Model

2003 ◽  
Vol 40 (6) ◽  
pp. 388-396 ◽  
Author(s):  
Tomio OKAWA ◽  
Akio KOTANI ◽  
Isao KATAOKA ◽  
Masanori NAITO
Keyword(s):  
Heat Flux ◽  
Critical Heat Flux ◽  
Annular Flow ◽  
Flow Model ◽  
Film Flow

An Investigation of Flow, Heat Transfer Characteristic of Annular Flow and Critical Heat Flux in Vertical Upward Round Tube

2006 ◽  
Author(s):  
Fan Pu ◽  
Suizheng Qiu ◽  
Guanghui Su ◽  
Dounan Jia
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Liquid Film ◽  
Critical Heat Flux ◽  
Heat Transfer Characteristic ◽  
Annular Flow ◽  
Transfer Characteristic ◽  
Round Tube

The term annular flow is used to describe the configuration of vapor-liquid flow in which part of the liquid travels as a film on the wall and the rest is entrained as drops by the vapor core in the center of the channel. The objective of this paper is to develop a hydrodynamic model for vertical upward annular flow. A separated flow model is developed and the conservations of Mass, Momentum, Energy, entrainment rate correlation in wide range of conditions and interfacial frictional correlation are used to research the flow and heat transfer characteristic of annular flow. The liquid film thickness, liquid film mass flow rate, two-phase heat transfer coefficient pressure along axial position, local velocity profiles along radial position are predicted theoretically. The influence of the mass flux, heat flux on liquid film thickness, heat transfer coefficient etc. are investigated in detail. The critical heat flux are also predicted in vertical upward round tube according to the theory that the dryout in vertical annular flow emerges at the point where the film is depleted due to the integrating result of entrainment, deposition and evaporation. The influence of mass flux, inlet mass quality and tube diameter on critical heat flux is also predicted in this paper. Finally the predicted result of critical heat flux is compared with experimental data, and the theoretical CHF values are higher than that of experimental data, with error within 30%.

Flow Behavior and Flow Boiling Heat Transfer in Thin-Rectangular Mini-Channels

2008 ◽  
Author(s):  
Yasuo Koizumi ◽  
Hiroyasu Ohtake ◽  
Tomonari Yamada
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flow Pattern ◽  
Critical Heat Flux ◽  
Boiling Heat Transfer ◽  
Annular Flow ◽  
Flow Channel ◽  
Heat Transfer Surface ◽  
Liquid Slug ◽  
Flux Condition

Boiling heat transfer of thin-rectangular channels of the width of 10 mm has been examined. The height of the flow channel was in a range from 0.6 mm to 0.4 mm. Experimental fluid was water. Bubbly flow, slug flow, semi annular flow and annular flow were observed. The flow pattern transition agreed well with the Baker flow pattern map for the usual sized flow path. The critical heat flux was lower than the value of the usual sized flow channel. The Koizumi and Ueda method predicted well the trend of the critical heat flux of the present experiments. At the critical heat flux condition, the heat transfer surface was covered by liquid slug, a large bubble pushed away the liquid slug, a dry area was formed on the heat transfer surface and then liquid slug came around to cover the heat transfer surface again. This process repeated rapidly. Following this observation, a heat transfer surface temperature calculation model at the critical heat flux condition was proposed. The calculated result re produced the experimental result.

scholarly journals Film flow on a wall and critical heat flux

2014 ◽  
Vol 1 (1) ◽  
pp. TEP0006-TEP0006 ◽  
Author(s):  
Yasuo KOIZUMI
Keyword(s):  
Heat Flux ◽  
Critical Heat Flux ◽  
Film Flow

scholarly journals A Separated-Flow Model for Predicting Flow Boiling Critical Heat Flux and Pressure Drop Characteristics in Microchannels

2012 ◽  
Author(s):  
Tie Jun Zhang ◽  
Siyu Chen ◽  
Evelyn N. Wang
Keyword(s):  
Heat Flux ◽  
Pressure Drop ◽  
Critical Heat Flux ◽  
Flow Model ◽  
Two Phase Flow ◽  
Flow Boiling ◽  
Separated Flow ◽  
Phase Flow ◽  
Two Phase ◽  
Microchannel Cooling

Two-phase microchannel cooling promises high heat flux removal for high-performance electronics and photonics. However, the heat transfer performance of flow boiling microchannels is limited by the critical heat flux (CHF) conditions. For variable heat inputs and variable fluid flows, it is essential to predict CHFs accurately for effective and efficient two-phase microchannel cooling. To characterize the CHF and pressure drop in flow boiling microchannels, a separated-flow model is proposed in this paper based on fundamental two-phase flow mass, energy, momentum conservation and wall energy conservation laws. With this theoretical framework, the relationship among liquid/vapor interfacial instability, two-phase flow characteristics and CHF is further studied. This mechanistic model also provides insight into the design and operational guidelines for advanced electronics and photonics cooling technologies.

Sign in / Sign up

Export Citation Format

Share Document