scholarly journals Resistance under Marshall monotonic load for asphalt concrete mixtures

2022 ◽  
Vol 2153 (1) ◽  
pp. 012006
Author(s):  
Y W Yung-Vargas ◽  
A Rodríguez-Lizcano ◽  
C A Peña-Soto
Keyword(s):  
Asphalt Concrete ◽  
Asphalt Mixtures ◽  
Raw Material ◽  
Asphalt Mixes ◽  
Asphalt Cement ◽  
Concrete Mixtures ◽  
Object Of Study ◽  
Marshall Stability ◽  
Monotonic Load ◽  
Mineral Aggregates

Abstract The dense hot MDC-19 type asphalt mixes are considered, by the “Instituto Nacional de Vías” in Colombia, as continuous grading asphalt mixes (asphalt concrete). These constitute most of the surface course, in the structures of in-service pavements, being the object of study and research in different projects to ensure their durability. In the present investigation, unlike other investigations, the mechanical behavior under Marshall monotonic load was studied in the laboratory between MDC-19 dense type asphalt mixtures, comparing plant-produced and laboratory-produced asphalt mixtures. To carry out this process, samples of uncompacted asphalt mixtures were taken, produced in four fixed plants, with which Marshall-type briquettes were compacted. Likewise, samples of mineral aggregates and asphalt cement were obtained from the same plants, which constitute the mixtures raw material produced there. With these materials, briquettes with the same characteristics were mixed and compacted. Subsequently, the resistance under Marshall monotonic load was determined on the briquettes manufactured in plant and laboratory. The optimal asphalt cement content was compared between plant and laboratory- produced mixtures. An increase in Marshall Stability was found in the briquettes made with plant-produced mixtures, while these required a greater amount of asphalt cement for their production.

scholarly journals Economic analysis of the inclusion of thermoelectric ash in asphalt mixtures

2021 ◽  
Vol 10 (10) ◽  
pp. e28101018564
Author(s):  
Igor Nonato Almeida Pereira ◽  
Newton Paulo de Souza Falcão ◽  
Consuelo Alves da Frota
Keyword(s):  
Asphalt Concrete ◽  
Lower Cost ◽  
Electric Energy ◽  
Asphalt Mixtures ◽  
Raw Material ◽  
Stone Dust ◽  
Alternative Material ◽  
Good Technique ◽  
Materials Used ◽  
The Cost

The replacement of conventional materials used in hot asphalt mixtures with others of good technique and lower cost and environmental impact has motivated research in this area of knowledge in recent decades. The researches should be expanded in the scope of engineering, given that it contributes considerably to the transformation of spaces and raw material. In this context, thermoelectric ashes, which are residues from the production of electric energy, appear as an alternative to replace the stone powder input which contributes negatively to the environment considering that it comes from the blasting of rocks. This work aims to compare the cost of producing traditional asphalt concrete (reference) to asphalt compositions containing 5,15% of alternative material characterized by stone dust. There was a saving of R$ 0.21 per ton of AC machining, consisting of thermoelectric ash as a partial substitute (5.15%) for stone powder, which represents significant savings in a practical context.

scholarly journals MAIN PROBLEMS OF MANUFACTURING ASPHALT CONCRETE MIXTURES IN LITHUANIA/ASFALTBETONIO MIŠINIŲ GAMYBOS SVARBIAUSIOS PROBLEMOS LIETUVOJE

2000 ◽  
Vol 6 (1) ◽  
pp. 39-45
Author(s):  
Donatas Čygas
Keyword(s):  
Asphalt Concrete ◽  
High Speed ◽  
Statistical Data ◽  
Concrete Mixture ◽  
Cement Material ◽  
Asphalt Cement ◽  
Concrete Mixtures ◽  
Concrete Quality ◽  
Regressive Analysis ◽  
Speed Gradient

The article describes the main problems of manufacturing asphalt concrete mixtures at the factories under Ministry of Communication in the Republic of Lithuania. The Lithuanian Road Network is up to 21.122 km of state roads. 1.455 km of them are motorways, 3.415 km—national roads and 16.251 km—regional roads. Half of the state roads in Lithuania are paved with asphalt concrete. 98% of the motorways and 36% of the regional roads have asphalt pavement. Asphalt concrete pavement resistance to corrosion can be increased by improving asphalt concrete mixture production technology: ie by updating technological equipment, changing technological conditions and developing new methods of asphalt concrete mixture production. Therefore, the updating of asphalt concrete mixture production technologies is a very important factor for improving road operating properties and ensuring proper duration of asphalt concrete pavements. Here is the essence of the new separate successive technology: crushed stone and sand are mixed with bitumen in the main asphalt concrete mixer, the amount of bitumen being calculated according to the bitumen absorption in the materials. Then the asphalt cement material produced in a separate high-speed mixer is passed, and the whole mixture is remixed in the main mixer and supplied to the customer. Both separate consequent technologies differ from each other in the order of supplying asphalt cement material into the main mixing unit. Separate successive technology was theoretically grounded by the correlation between the technological thickness of bituminous film and the chemical-mineralogical composition and size of constituents, by the correlation between the particle size and their capability to compose aggregates, by the emergence of the oriented binding material coating on the technological bituminous film encoating mineral particles. Special attention is given to the manufacturing of asphalt cement material in a separate high-speed mixer (3 Table). It was theoretically grounded that mineral filler passing through the intensive shift zone between the paddle ends of the high-speed mixer and the walls of mixing chamber disintegrate and new active surfaces become visible. The molecular structure changes and free radicals appear. This intensive mixing guarantees high bitumen adsorption on the surface of mineral filler, which increases asphalt concrete resistance to corrosion and its durability, improves ecological environment in the asphalt concrete plant. In order to confirm the reliability of research results and explain correlative and regressive regularity, statistical data were processed applying statistical data processing programming system “STATGRAPHICS”. The linear regressive analysis for determining close relations of separate asphalt concrete quality indicators with speed gradient of asphalt cement material shift in a high-speed mixer was performed. Therefore, the possibility to change shift speed gradient from 3000 to 5000 1/s is provided in terms of reference for manufacturing asphalt concrete mixing plant. Correlation between separate asphalt concrete quality indicators and asphalt cement material shift speed gradient as well as bitumen amount in the asphalt cement material was determined by multi-dimensional regressive analysis of experimental data. The calculated correlation factor squared (R2) and F criteria indicate the adequacy and reliability of the multidimensional regression model.

scholarly journals Selecting warm mix asphalt additives by the properties of warm mix asphalt mixtures - China experience

2015 ◽  
Vol 10 (1) ◽  
pp. 79-88 ◽  
Author(s):  
Xinsheng Li ◽  
Zhaoxing Xie ◽  
Wenzhong Fan ◽  
Lili Wang ◽  
Junan Shen
Keyword(s):  
Tensile Strength ◽  
Dynamic Stability ◽  
Asphalt Concrete ◽  
Warm Mix Asphalt ◽  
Asphalt Mixtures ◽  
Air Voids ◽  
Mastic Asphalt ◽  
Stone Mastic Asphalt ◽  
Crushed Aggregate ◽  
Marshall Stability

The objective of this research was to select the most effective warm asphalt additives for mix practice based on a series of laboratory testing programs such as density, Marshall stability, freeze-thaw splitting strength, dynamic stability, and bending beam strain. The experimental design of warm mix asphalt included the use of three commonlyused additives, two typical aggregate gradations, one crushed aggregate, and one modified asphalt. Results showed that: (1) the bulk specific gravity and air voids of all the mix specimens were similar to those of controls; (2) the Marshall stability and flow values of the warm stone mastic asphalt were 6.8%–26.6% and 3.5%–10.3%% higher than those of controls, respectively, and those of the warm asphalt concrete were 6.1%–15.6% and 6.5%–9.7% higher than those of controls, respectively; (3) the indirect tensile strength of two types of mixtures was 1.7%–14.4% lower than that of controls, and the average tensile strength ratio of the warm stone mastic asphalt and asphalt concrete was 4.3% and 1.3% higher than that of controls, respectively; (4) the dynamic stability of warm mix specimens was 10.8%–16.6% lower than that of the controls; (5) the average bending failure strain of warm stone mastic asphalt was 7.6% higher than that of the controls, and that of warm asphalt concrete was 12.8% lower than that of the controls; (6) Overall, warm asphalt mixtures with Sasobit and Rediset had relatively best performances required in Southeast China, where rutting and stripping are the main failures of asphalt pavements.

Effect of Modified Asphalt Cement of the Performance of Stone Matrix Mixtures

2020 ◽  
Vol 38 (5A) ◽  
pp. 789-800
Author(s):  
Duaa A. Khalaf ◽  
Zaynab I. Qasim ◽  
Karim H. Al Helo
Keyword(s):  
Tensile Strength ◽  
Fracture Resistance ◽  
Laboratory Tests ◽  
Asphalt Binder ◽  
Asphalt Mixtures ◽  
Indirect Tensile Strength ◽  
Asphalt Cement ◽  
Indirect Tensile ◽  
Marshall Stability ◽  
Stone Matrix

This research investigates the behavior of Stone Matrix Asphalt mixtures (SMA) modified with styrene-butadiene-styrene (SBS) polymer at four percentages (1, 2, 3 and 4%) by weight of asphalt cement. The moisture susceptibility and rutting were taken into consideration in this study. To achieve the objective of this research the superpave system is conducted to design the asphalt mixtures. The physical properties of aggregate, bitumen and other mix materials were assessed and evaluated with the laboratory tests. The mixtures were prepared using penetration Graded (40-50) bitumen and a chemical named Polypropylene Fibers was used as a stabilizing additive. Fibers have been used in SMA mixtures for two main reasons: To increase the toughness and fracture resistance of hot mix asphalt (HMA) and to act as a stabilizer to prevent drain down of the asphalt binder. The laboratory tests include indirect tensile strength test, Marshall stability and retained Marshall Stability test (RMS). For rutting test the Roller wheel compactor is used for preparing the asphaltic samples and Wheel tracking device is used to evaluate the rutting of asphaltic slabs. The results showed that the SBS polymer asphalt mixture gave better moisture sensitivity and better fracture resistance according to the study.It is noted that indirect tensile strength ratio (TSR) increases by 93.1 % and the rut depth decreases by 32.5 % when adding 3% SBS polymer to SMA.

Comparison of mechanistic laboratory characterization and 10-year rutting performance of SPS-9A test site in Saskatchewan

2010 ◽  
Vol 37 (3) ◽  
pp. 489-495
Author(s):  
Curtis Berthelot ◽  
Diana Podborochynski ◽  
Ania Anthony ◽  
Brent Marjerison
Keyword(s):  
Asphalt Concrete ◽  
Asphalt Binder ◽  
Test Site ◽  
Performance Comparison ◽  
Test Results ◽  
Frequency Sweep ◽  
Asphalt Mixes ◽  
Asphalt Cement ◽  
Laboratory Characterization ◽  
Frequency Sweep Test

This paper provides a performance comparison of mechanistic laboratory and field rutting performance of four asphalt concrete mixes constructed in 1996 at a Strategic Highway Research Program SPS-9A test site located in Saskatchewan. The asphalt mixes included two Saskatchewan Type 70 Marshall mixes and two coarse graded Superpave™ mixes and employed 150–200A and 200–300A penetration grade asphalt cement binders. The triaxial frequency sweep characterization determined that the Superpave™ mix yielded improved mechanistic structural constitutive properties when compared to the Saskatchewan Type 70 mix. In addition, improved mechanistic structural properties were observed with the mixes employing 150–200A (PG 58-28) asphalt binder relative to the 200–300A (PG 52-34) asphalt binder, particularly the Saskatchewan Type 70 mix. The 10-year rutting performance of the Radisson SPS-9A test site was evaluated and the field rutting results concurred with the triaxial frequency sweep test results. The triaxial frequency sweep characterization employed in this study appears to adequately rank asphalt mixes with respect to field rutting performance.

Investigation of the effects of different polymer-modified asphalt cements on asphalt mixes at low temperature

2007 ◽  
Vol 34 (5) ◽  
pp. 589-597 ◽  
Author(s):  
K Kandil ◽  
A O Abd El Halim ◽  
Y Hassan ◽  
A Mostafa
Keyword(s):  
Low Temperature ◽  
High Resistance ◽  
Asphalt Concrete ◽  
Elevated Temperatures ◽  
Winter Season ◽  
Experimental Program ◽  
Asphalt Cement ◽  
Modified Asphalt ◽  
Concrete Mixtures ◽  
Polymer Modified Asphalt

The extreme environmental conditions in Canada require the use of asphalt cement that can provide a high resistance to low-temperature cracking during the winter season and a high resistance to rutting due to the elevated temperatures in the summer. Earlier studies showed that such desired improvements in the quality of asphalt cement could be achieved using polymer-modified asphalt (PMA) cement. This paper presents a three-phase experimental program that was carried out to evaluate the expected performance of asphalt concrete mixtures with PMA compared to asphalt concrete mixtures with conventional and air-oxidized asphalt binders. The results of this study show that PMA in asphalt concrete mixes would significantly improve the resistance to cracking (loading and low-temperature). Key words: asphalt mixtures, polymer-modified asphalt, conventional asphalt cement, air-oxidized asphalt, testing.

scholarly journals Moisture Susceptibility of Asphalt Concrete Pavement Modified by Nanoclay Additive

2019 ◽  
Vol 5 (12) ◽  
pp. 2535-2553 ◽  
Author(s):  
Saif Al-din Majid Ismael ◽  
Mohammed Qadir Ismael
Keyword(s):  
Asphalt Concrete ◽  
Hot Mix Asphalt ◽  
Asphalt Mixture ◽  
Moisture Damage ◽  
Strength Ratio ◽  
Moisture Susceptibility ◽  
Asphalt Cement ◽  
Asphalt Content ◽  
Marshall Stability ◽  
Asphalt Concrete Pavement

Durability of hot mix asphalt (HMA) against moisture damage is mostly related to asphalt-aggregate adhesion. The objective of this work is to find the effect of nanoclay with montmorillonite (MMT) on Marshall properties and moisture susceptibility of asphalt mixture. Two types of asphalt cement, AC(40-50) and AC(60-70) were modified with 2%, 4% and 6% of Iraqi nanoclay with montmorillonite. The Marshall properties, Tensile strength ratio(TSR) and Index of retained strength(ISR) were determined in this work. The total number of specimens was 216 and the optimum asphalt content was 4.91% and 5% for asphalt cement (40-50) and (60-70) respectively. The results showed that the modification of asphalt cement with MMT led to increase Marshall stability and the addition of 6% of MMT recorded the highest increase, where it increased by 26.35% and 22.26% foe asphalt cement(40-5) and(60-70) respectively. Also, the addition of MMT led to increase moisture resistance of asphalt mixture according to the increase in TSR and IRS. The addition of 4% and 6% of MMT recorded the highest increase in TSR and IRS for asphalt cement (40-50) and (60-70) respectively, where they increased by 11.8% and 17.5% respectively for asphalt cement (40-50) and by 10% and 18% respectively for asphalt cement (60-70).

scholarly journals Influence of Polypropylene Length on Stability and Flow of Fiber-reinforced Asphalt Mixtures

2016 ◽  
Vol 2 (10) ◽  
pp. 538-545 ◽  
Author(s):  
Ramin Bayat ◽  
Siamak Talatahari
Keyword(s):  
Asphalt Concrete ◽  
Asphalt Pavement ◽  
Flexible Pavements ◽  
Asphalt Mixture ◽  
Fatigue Cracking ◽  
Asphalt Mixtures ◽  
Concrete Mixture ◽  
Fiber Reinforced ◽  
Surface Distress ◽  
Marshall Stability

Engineers are constantly trying to improve the performance of the flexible pavements. The main surface distress types which cause maintenance and disruption are rutting and fatigue cracking. For solving these problems, many studies have been carried out until now, ranged from changing gradation to adding polymers and fibers to asphalt mixture. In this study, polypropylene additive was selected as fiber additive because of low costing and having good correlation with asphalt pavement. Three type of polypropylene additive in the length 6, 12 and 19 mm were selected and used at five different percentages in the asphalt concrete mixture. Asphalt specimens were analysed by Marshall Analysis and finally tested by Marshall Stability apparatus. Adding polypropylene increased Marshall Stability (38%), and decreased Flow (39%). These results show that polypropylene can be helpful for increasing pavement life.

scholarly journals Influence of Water Immersion on Stability of AC-WC Mixed with Gondorukem Additional Material

2021 ◽  
Vol 921 (1) ◽  
pp. 012067
Author(s):  
D R G Kabo ◽  
M Tumpu ◽  
H Parung
Keyword(s):  
Asphalt Concrete ◽  
Immersion Time ◽  
Water Immersion ◽  
Asphalt Mixtures ◽  
Additional Material ◽  
Influence Of Water ◽  
Asphalt Content ◽  
The Stability ◽  
Marshall Stability ◽  
Time Decrease

Abstract One of the treatments that can be given to asphalt mixtures to determine the durability of the mixture is by water immersion. This study aims to analyze the stability value of Marshall mixture of AC-WC (Asphalt Concrete Wearing Course) by using modified Asbuton as a binder and gondorukem as added material due to water immersion. The method used in this research is experimental in the laboratory. AC-WC mixture is produced using modified Asbuton as a binder (Retona Blend 55) at optimum asphalt content of 6.25% and gondorukem as an additive at 0.0% and 2.5% content. The treatment given to the mixture is by soaking water for 0, 1, 3 and 7 days. The treatment given to the mixture is by soaking water for 0, 1, 3 and 7 days. The results showed that the Marshall stability value decreased with increasing water immersion time. Decrease in Marshall stability values that occur in specimens with immersion time of 1, 3 and 7 days for specimens without immersion are 21.34%, 25.56% and 28.25%, respectively.

scholarly journals Modification of bituminous binders for guss asphalt

2021 ◽  
Vol 274 ◽  
pp. 02011
Author(s):  
Marina Vysotskaya ◽  
Anastasia Kurlykina ◽  
Artem Shiryaev ◽  
Anna Tkacheva ◽  
Dmitry Litovchenko
Keyword(s):  
Asphalt Concrete ◽  
Raw Material ◽  
Structural Defects ◽  
Concrete Pavements ◽  
Self Healing ◽  
Modified Bitumen ◽  
Concrete Mixtures ◽  
Bridge Structures ◽  
Bituminous Binders ◽  
Thermal Stability Of

Over the past few years, the research of the use of cast asphalt concrete mixtures in the upper layers of the coating of bridge structures has been actively carried out. The experience gained allows us to conclude that one of the most common effective ways to improve the durability and thermal stability of cast asphalt concrete pavements is the use of modified bituminous binders. The modified bitumen part of cast asphalt concrete acts as a medium capable of initiating the «self-healing» of the composite, independently eliminating structural defects. This study aims to research the rheological characteristics of modified bituminous binders. Bitumen grade BND 50/70 was used as a raw material in the study; the following types of additives were used as its modifiers: rubber modifier (RM), EVATHERM and SBS. The optimal concentrations of the proposed additives for modification allowing to achieve the effect of structuring the mastic component of cast asphalt concrete with insignificant increases in the temperatures of mixing and compaction of mixtures based on them have been revealed.

Sign in / Sign up

Export Citation Format

Share Document