scholarly journals Physical and mechanical properties of mortars containing date palm fibers

2022 ◽  
Author(s):  
Saleh Bamaga
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Water Absorption ◽  
Absorption Rate ◽  
Date Palm ◽  
Physical And Mechanical Properties ◽  
Water Absorption Rate ◽  
Date Palm Fibers ◽  
Rate Test ◽  
Construction Works

Abstract This paper presents the results of a study conducted to investigate the effects of incorporating Sefri Date Palm Leave Fibers (SDPLF) into the mortar. A total of seven mixtures were prepared and tested. SDPLF were collected from local farms. The fibers were then cleaned, dried, and cut to different sizes of 10 mm, 20 mm, and 50 mm, maintaining the same individual fiber width of approximately 5±2 mm. The content of SDPLF in mortars was kept to 1% and 3% by mass. The physical and mechanical properties of SDPLF fibers and SDPLF mortars were investigated. The compressive strength at 7, 14, and 28 days was determined. The water absorption rate test was carried out on mortars containing 1% SDPLF fibers. The results showed that mortars with SDPLF have lower workability, lower density, and lower compressive strength as compared to control mortars. However, they are still acceptable for use in construction works. Mortars containing 10 mm and 20 mm SDPLF fibers by mass showed significant improvement in terms of water absorption rate as compared to the control mortar.

scholarly journals The Physical and Mechanical Properties of Corn-based Bioplastic Films with Different Starch and Glycerol Content

2021 ◽  
Vol 32 (3) ◽  
pp. 89-101
Author(s):  
Nur Nadia Nasir ◽  
◽  
Siti Amira Othman ◽  
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Absorption Rate ◽  
Corn Starch ◽  
Physical And Mechanical Properties ◽  
High Strength ◽  
Major Drawback ◽  
Water Absorption Rate ◽  
Strength And Stiffness ◽  
Mechanical Tensile

Petroleum-based plastics have had a long history with varied materials and applications. However, the major drawback with these plastics is their harmful impact on the environment. Poor disposal management of these plastics have ultimately affected humans. Therefore, starch-based bioplastics have been widely used because of their renewability, sustainability and cost-effectiveness. This work investigated the effect of different concentrations of corn starch (10%, 15%, and 20% w/w of distilled water) and glycerol (20%, 30%, and 40% w/v of corn starch) on the properties of corn-based bioplastic films. Particularly, mechanical (tensile strength, Young’s modulus and elongation at break) and physical (water absorption rate and moisture content) properties were investigated. These films were prepared by the solvent casting method. It was demonstrated that the addition of 30% glycerol produced mechanical properties closest to the standard value, while films with a composition of 15% of corn starch had the most optimised value. Meanwhile, 20% glycerol and 20% corn starch produced a film with high strength and stiffness but lacked flexibility. Higher concentrations of starch and glycerol produced the highest moisture and water absorption rate. This was due to the highly hydrophilic nature of both corn starch and glycerol. However, the concentration of glycerol needs to be adjusted based on the intended use of the film. In conclusion, the concentration of corn starch and glycerol produced slightly different outcomes. Thus, the properties and application of the cornbased bioplastic films can be maximised by optimising the concentration of corn starch and glycerol.

scholarly journals The numerical simulation of Influence of Drying-wetting Cycles on the Deterioration Characteristics of Gypsum Rocks under Particle Flow Code

2020 ◽  
Vol 24 (1) ◽  
pp. 55-59
Author(s):  
Guopeng Wu ◽  
Wenwu Chen ◽  
Kai Cui
Keyword(s):  
Mechanical Properties ◽  
Numerical Simulation ◽  
Water Absorption ◽  
Absorption Rate ◽  
Early Stage ◽  
Particle Flow ◽  
Wetting And Drying ◽  
Water Absorption Rate ◽  
Gypsum Rock ◽  
Deterioration Characteristics

In order to study the influence of dry-wet cycling on the deterioration characteristics of gypsum rocks and solve the problems encountered in engineering construction, in this study, gypsum rocks are taken as the research object. With the combination of laboratory test and theoretical analysis, the numerical simulation of particle flow is carried out, and the deterioration characteristics of physical and mechanical properties of gypsum rock under dry-wet cycling are studied. The results show that gypsum, quartz, zeolite and dolomite are the main components of gypsum rocks. Gypsum occupies the most components in gypsum rocks, so the various characteristics of gypsum greatly affect the characteristics of gypsum rocks. The process of water absorption and loss of gypsum is similar, which shows that the rate of water absorption or loss of gypsum is faster in the early stage, and tends to be stable in the later stage. The curve of the whole process of water absorption and loss is fitted by negative exponential function, and the effect is better. The larger the porosity of gypsum rock is, the better its water absorption performance is. Intergranular pore, dissolution pore and dissolution pore are the main pore types of gypsum rock. Intergranular pore is the main water absorption channel of gypsum rock. The cumulative water absorption increases with the increase of wetting and drying cycles. The change of water absorption curve is mainly manifested in water absorption rate and time. The more the number of wet-dry cycles is, the higher the water absorption rate in the early stage of water absorption is, the closer the characteristic curve to the coordinate axis of water absorption is, and the shorter the water absorption time is. In contrast, the shape difference of water loss curve is very small. It can be seen from this that in the process of wetting and drying cycle, the hydrophysical and hydrochemical processes promote each other, which changes the crystal structure and pore structure of gypsum rocks, reduces the crystal strength and increases the porosity, thus leading to the deterioration of the mechanical properties of gypsum rocks.

scholarly journals THE DEPENDENCE OF THE PHYSICAL MECHANICAL PROPERTIES OF EXPANDED-CLAY LIGHTWEIGHT CONCRETE ON THE COMPOSITION

2010 ◽  
Vol 2 (6) ◽  
pp. 50-55
Author(s):  
Marija Vaičienė ◽  
Jurgita Malaiškienė
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Chemical Composition ◽  
Water Absorption ◽  
Lightweight Concrete ◽  
Physical And Mechanical Properties ◽  
Concrete Mixture ◽  
Active Filler ◽  
Binder Material ◽  
Substitute Materials

Binder material is the most expensive raw component of concrete; thus, scientists are looking for cheaper substitute materials. This paper shows that when manufacturing, a part of the binder material of expanded-clay lightweight concrete can be replaced with active filler. The conducted studies show that technogenic – catalyst waste could act as similar filler. The study also includes the dependence of the physical and mechanical properties of expanded-clay lightweight concrete on the concrete mixture and the chemical composition of the samples obtained. Different formation and composition mixtures of expanded-clay lightweight concrete were chosen to determine the properties of physical-mechanical properties such as density, water absorption and compressive strength.

scholarly journals Effect of fly ash on physical and mechanical properties of mortar

2019 ◽  
Vol 17 (6) ◽  
pp. 35
Author(s):  
Vu-An Tran
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Water Absorption ◽  
Thermal Power ◽  
Setting Time ◽  
Physical And Mechanical Properties ◽  
Flow Density ◽  
Control Specimen

This research investigates the physical and mechanical properties of mortar incorporating fly ash (FA), which is by-product of Duyen Hai thermal power plant. Six mixtures of mortar are produced with FA at level of 0%, 10%, 20%, 30%, 40%, and 50% (by volume) as cement replacement and at water-to-binder (W/B) of 0.5. The flow, density, compressive strength, flexural strength, and water absorption tests are made under relevant standard in this study. The results have shown that the higher FA content increases the flow of mortar but significantly decreases the density of mixtures. The water absorption and setting time increases as the samples incorporating FA. Compressive strength of specimen with 10% FA is approximately equal to control specimen at the 91-day age. The flexural strength of specimen ranges from 7.97 MPa to 8.94 MPa at the 91-day age with the best result for samples containing 10% and 20% FA.

scholarly journals Evaluation of Cassava Effluent as Organic Admixture in Concrete Production for Farm Structures

2020 ◽  
pp. 271-282
Author(s):  
Ovie Isaac AKPOKODJE ◽  
Goodnews Goodman AGBI ◽  
Hilary UGURU
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Fresh Water ◽  
Absorption Rate ◽  
International Standards ◽  
Partial Replacement ◽  
Strength Development ◽  
Water Absorption Rate ◽  
Concrete Production ◽  
Farm Structures

This paper evaluated the influence of cassava effluent on the compressive strength of concrete for farm structures. Three sets of concrete cubes were produced with a concrete mix ratio of 1:2:4 (C 15) and a water to cement ratio (w c-1) of 0.5. The 1st set was produced with 100% fresh water (tap water). The 2nd set was produced with 75% partial replacement of the fresh water with fresh cassava effluent, while the 3rd set was produced with 75% partial replacement of the fresh water with old cassava effluent. The density, water absorption rate and compressive strength of the concrete cubes was tested in accordance with ASTM International standards, at the end of 7, 14, 21, 28 and 56 curing days. The results revealed that, the cassava effluent slightly increased the cubes density; but reduced their water absorption rate. The study further showed that, concrete produced with fresh cassava effluent, developed the highest compressive strength (29.57 MPa) at the end of the 56th curing day. In contrast, concrete produced with old cassava effluent developed the lowest compressive strength (24.43 MPa) at day 56, which was lower than the compressive strength of 27.18 MPa developed by the concrete produced with fresh water (also at day 56). In addition, the cassava effluent retarded the initial rate of strength development, as such, increasing its prospect as an organic concrete admixture. This study will be helpful in mitigating the harmful effects of cassava effluent in the environment, since it can be utilized in concrete production.

scholarly journals The Effects of Different Nanoadditives on the Physical and Mechanical Properties of Similar Silty Mudstone Materials

2020 ◽  
Vol 2020 ◽  
pp. 1-11 ◽  
Author(s):  
Ji-jing Wang ◽  
Zhen-ning Shi ◽  
Ling Zeng ◽  
Shuang-xing Qi
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Water Absorption ◽  
Natural Water ◽  
Physical And Mechanical Properties ◽  
Mechanical Parameters ◽  
Similar Material ◽  
Silty Mudstone ◽  
Similar Materials ◽  
Softening Coefficient

In order to analyze the influence of different nanoadditives on the physical and mechanical properties of similar silty mudstone materials, nano-TiO2 (NTi), nano Al2O3 (NAl), and nanobentonite (NBe) were added to improve the physical and mechanical properties of silty mudstone similar materials. The physical and mechanical parameters are more in line with silty rock. Finally, nanometer additives suitable for silty mudstone similar materials are determined by conducting density test, natural water absorption test, uniaxial compression test, splitting test, softening coefficient test, expansibility test, and microscopic test. The effects of adding NTi, NAl, and NBe on improving the physical and mechanical properties of silty mudstone similar materials were studied to analyze the influence law of different NTi, NAl, and NBe contents on similar material density, natural water absorption, uniaxial compressive strength, tensile strength, softening coefficient, expansion rate, and other physical and mechanical parameters. The microscopic morphology of similar materials was analyzed by scanning electron microscopy and the mechanism of influence of nanoadditives on the microscopic structure of samples was revealed. The results are as follows. (1) The density of similar materials of silty mudstone increases with the increase of the content of nanoadditive. The natural water absorption rate decreased first and then increased with the increase of the content of nanometer additives, while the softening coefficient decreased with the increase of the content of nanometer additives. The uniaxial compressive strength and tensile strength increased first and then decreased with the increase of the content of nanometer additives. This is due to the incorporation of the nanoadditive amount effective to promote the hydration reaction of gypsum and accelerate the production of cement, while a similar material may be filled in the pores, reducing the internal defects, a similar material to make denser; when excessive dosage, nanoadditives agglomeration occurs, resulting in deterioration of the effect, but will reduce the mechanical properties of similar materials. (2) When the content of NBe is 6%, the physical and mechanical parameters of similar materials can reach or be closer to the silty raw rock except uniaxial compressive strength. The failure mode of the uniaxial compression specimen is also the same as that of the original rock, which can be used as the best choice. The research results laid the foundation for further analysis of NBe application in similar materials.

scholarly journals Characterization of Slag Cement Mortar Containing Nonthermally Treated Dried Red Mud

2019 ◽  
Vol 9 (12) ◽  
pp. 2510 ◽  
Author(s):  
Gyeongcheol Choe ◽  
Sukpyo Kang ◽  
Hyeju Kang
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Water Content ◽  
Red Mud ◽  
Absorption Rate ◽  
Cement Mortar ◽  
Slag Cement ◽  
X Ray ◽  
Water Absorption Rate ◽  
High Calcium

In this study, a method was suggested to produce dried powder from red mud (RM) sludge with 40%–60% water content without heating. The RM sludge is discharged from the Bayer process, which is used to produce alumina from bauxite ores. Nonthermally treated RM (NTRM) powder was produced by mixing RM sludge (50%), paper sludge ash (PSA, 35%), and high-calcium fly ash (HCFA, 15%). The physicochemical properties of NTRM were investigated by analyzing its water content, X-ray fluorescence spectra, X-ray diffraction patterns, and particle size. Moreover, to examine the applicability of NTRM as a construction material, slag cement mortar in which 20 wt% of the binder was replaced with NTRM was produced, and the compressive strength, porosity, and water absorption rate of the mortar were evaluated. Results indicated that NTRM of acceptable quality was produced when the water content in RM sludge decreased and CaO contained in PSA and HCFA reacted with moisture and formed portlandite. The NTRM-mixed mortar requires further examination in terms of durability because of the increased capillary voids and high water absorption rate, but its compressive strength is sufficient to enable its use in sidewalks, bike roads, and parking lots.

Strength and Water Absorption Rate of Concrete Made from Palm Oil Fuel Ash

2017 ◽  
Vol 889 ◽  
pp. 261-264 ◽  
Author(s):  
Norpadzlihatun Manap ◽  
Nor Izzah Muhamad ◽  
Kavitha Sandirasegaran
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Palm Oil ◽  
Absorption Rate ◽  
Conventional Concrete ◽  
Palm Oil Fuel Ash ◽  
Water Absorption Rate ◽  
Fuel Ash ◽  
Palm Oil Mill ◽  
Oil Fuel

Concrete is one of the most important materials for construction industry. The material in the mixture of concrete includes cement, sand and coarse aggregate. Production of cement causes the air pollution from the emission of carbon dioxide to the air. This research studies the replacement of cement with palm oil fuel ash (POFA) in the concrete mixture. The objective of this research is to investigate the compressive strength of concrete and water absorption rate of concrete made from POFA and to compare the strength and absorption rate between conventional concrete and concrete made from POFA. This is to indicate whether the compressive strength and absorption rate are equivalent to the strength of conventional concrete. The methodology used in this research is experimental method and the palm oil fuel ash was taken from palm oil mill in Cha’ah, Johor, Malaysia. The results of this research are the specimens which contain 20% POFA has a compressive strength and water absorption rate comparable to conventional concrete.

scholarly journals Physical and Mechanical Properties of a Porous Material Obtained by Low Replacement of Volcanic Ash by Aluminum Beverage Cans

2021 ◽  
pp. 1-11
Author(s):  
Bernard Missota Priso Dickson ◽  
Claudine Mawe Noussi ◽  
Louise Ndongo Ebongue ◽  
Joseph Dika Manga
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Porous Material ◽  
Water Absorption ◽  
Bulk Density ◽  
Volcanic Ash ◽  
Physical And Mechanical Properties ◽  
Apparent Porosity ◽  
Partial Replacement ◽  
Inorganic Polymers

This study focuses on the evaluation of the physical and mechanical properties of a porous material based on a mixture of powder (Volcanic ash /Aluminum Beverage Cans) and a solution of phosphoric acid. Volcanic ash (VA) use was collected in one of the quarries of Mandjo (Cameroon coastal region), crushed, then characterized by XRF, DRX, FTIR and named MaJ. The various polymers obtained are called MaJ0, MaJ2.5, MaJ5, MaJ7.5 and MaJ10 according to the mass content of the additions of the powder from the aluminum beverage cans (ABCs). The physical and mechanical properties of the synthetic products were evaluated by determining the apparent porosity, bulk density, water absorption and compressive strength. The results of this study show that the partial replacement of the powder of VA by that of ABC leads to a reduction in the compressive strength (5.9 - 0.8 MPa) and bulk density (2.56 – 1.32 g/cm3) of the polymers obtained. On the other hand, apparent porosity, water absorption and pore formation within the polymers increases with addition of the powder from the beverage cans. All of these results allow us to agree that the ABCs powder can be used as a blowing agent during the synthesis of phosphate inorganic polymers.

Use of polyvinyl chloride (PVC) powder and granules as aggregate replacement in concrete mixtures

2016 ◽  
Vol 23 (2) ◽  
pp. 209-216 ◽  
Author(s):  
Hakan Bolat ◽  
Pınar Erkus
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Water Absorption ◽  
Polyvinyl Chloride ◽  
Physical And Mechanical Properties ◽  
High Strength ◽  
Capillary Water ◽  
Capillary Water Absorption ◽  
Concrete Mixtures ◽  
Compressive Strength Test

AbstractConcrete is one of the materials in which polymer wastes are utilized. Generally, these wastes are added at specific rates in scientific studies but an important problem of waste polymers is size irregularity. Even when consistent dosage rates are used, variations in polymer size can lead to variability in the physical and mechanical properties of the concrete produced. The aim of this study is to determine physical and mechanical properties of polyvinyl chloride (PVC)-containing concretes. In order to produce normal and high strength concretes, 10%, 20%, and 30% replacement ratios of PVC powder and granules by volume of aggregate are used. Slump, fresh and hardened densities, compressive strength, capillary water absorption, and abrasion were tested on all concrete types. As the PVC ratio increases, important changes are seen in all physical and mechanical concrete properties. The unit weights of the 10%, 20%, and 30% replacement PVC powder concretes are lower by ∼4%, 8%, and 13%, respectively, as compared to the reference mixtures, and the replacement PVC granule concretes are lower by ∼2%, 4%, and 7%. Compressive strength test results showed similar trends. As PVC replacement increases, the capillary water absorption decreases between 10% and 50%, and abrasion decreases between 27% and 77%.

Sign in / Sign up

Export Citation Format

Share Document