scholarly journals Development of Al-SiC composite material from rice husk and its parametric assessment

Author(s):  
Madhusudan Baghel ◽  
C M Krishna ◽  
S. Suresh

Abstract In this research work, the development of Al-SiC composite material from rice husk and its parametric assessment is done using a CNC milling machine. They are further surface characterized, and mechanical properties such as BET surface area, SEM-EDX, and XRD, fracture toughness, tensile, and bending strength are studied. The machinability of the components is investigated for selected values of input-output parameters. Three castings, each with different particulate reinforcement combinations, are made with aluminum alloy (6061) using the stir casting method. BET surface area of extracted silica and Al-SiC composite material was found 374 m2/g and 150 m2/g, respectively. From results of BET surface area revealed that silica obtained from rice husk is more heterogeneous with a large surface area. A heterogeneous surface with larger pores was found through SEM images. XRD diffraction peaks show changes of amorphous silica into crystallinity in the composite material. The results also indicate that fracture toughness is very good at low temperatures and good machinability on CNC milling machines makes it suitable for aerospace applications.

Processes ◽  
2021 ◽  
Vol 9 (7) ◽  
pp. 1238
Author(s):  
Garven M. Huntley ◽  
Rudy L. Luck ◽  
Michael E. Mullins ◽  
Nick K. Newberry

Four naturally occurring zeolites were examined to verify their assignments as chabazites AZLB-Ca and AZLB-Na (Bowie, Arizona) and clinoptilolites NM-Ca (Winston, New Mexico) and NV-Na (Ash Meadows, Nevada). Based on powder X-ray diffraction, NM-Ca was discovered to be mostly quartz with some clinoptilolite residues. Treatment with concentrated HCl (12.1 M) acid resulted in AZLB-Ca and AZLB-Na, the chabazite-like species, becoming amorphous, as confirmed by powder X-ray diffraction. In contrast, NM-Ca and NV-Na, which are clinoptilolite-like species, withstood boiling in concentrated HCl acid. This treatment removes calcium, magnesium, sodium, potassium, aluminum, and iron atoms or ions from the framework while leaving the silicon framework intact as confirmed via X-ray fluorescence and diffraction. SEM images on calcined and HCl treated NV-Na were obtained. BET surface area analysis confirmed an increase in surface area for the two zeolites after treatment, NM-Ca 20.0(1) to 111(4) m2/g and NV-Na 19.0(4) to 158(7) m2/g. 29Si and 27Al MAS NMR were performed on the natural and treated NV-Na zeolite, and the data for the natural NV-Na zeolite suggested a Si:Al ratio of 4.33 similar to that determined by X-Ray fluorescence of 4.55. Removal of lead ions from solution decreased from the native NM-Ca, 0.27(14), NV-Na, 1.50(17) meq/g compared to the modified zeolites, 30 min HCl treated NM-Ca 0.06(9) and NV-Na, 0.41(23) meq/g, and also decreased upon K+ ion pretreatment in the HCl modified zeolites.


2021 ◽  
Author(s):  
Emmanuel Ayodele ◽  
Victoria Ezeagwula ◽  
Precious Igbokwubiri

Abstract Bamboo trees are one of the fastest growing trees in tropical rainforests around the world, they have various uses ranging from construction to fly ash generation used in oil and gas cementing, to development of activated carbon which is one of the latest uses of bamboo trees. This paper focuses on development of activated carbon from bamboo trees for carbon capture and sequestration. The need for improved air quality becomes imperative as the SDG Goal 12 and SDG Goal13 implies. One of the major greenhouse gases is CO2 which accounts for over 80% of greenhouse gases in the environment. Eliminating the greenhouse gases without adding another pollutant to the environment is highly sought after in the 21st century. Bamboo trees are mostly seen as agricultural waste with the advent of scaffolding and other support systems being in the construction industry. Instead of burning bamboo trees or using them for cooking in the local communities which in turn generates CO2 and fly ash, an alternative was considered in this research work, which is the usage of bamboo trees to generate activated, moderately porous and high surface area carbon for extracting CO2 from various CO2 discharge sources atmosphere and for water purification. This paper focuses on the quality testing of activated carbon that can effectively absorb CO2. The porosity, pore volume, bulk volume, and BET surface area were measured. The porosity of the activated carbon is 27%, BET surface area as 1260m²/g. Fixed carbon was 11.7%, Volatility 73%, ash content 1.7%.


Author(s):  
Garven M Huntley ◽  
Rudy Lin Luck ◽  
Michael E Mullins ◽  
Nick K Newberry

Four naturally occurring zeolites AZLB-Ca and AZLB-Na (Bowie, Arizona), NM-Ca (Winston, New Mexico), and NV-Na (Ash Meadows, Nevada) were studied to evaluate structural modifications after treatment with HCl acid. AZLB-Ca and AZLB-Na are chabazite-like species and become amorphous when boiled in concentrated HCl acid as confirmed by powder X-ray diffraction. In contrast, NM-Ca and NV-Na which are clinoptilolite-like species withstood boiling in concentrated HCl acid. This treatment removes calcium, magnesium, sodium, potassium, aluminum, and iron atoms or ions from the framework while leaving the silicon framework intact as confirmed via X-ray fluorescence and diffraction. SEM images on calcined and HCl treated NV-Na were obtained. BET surface area analysis confirmed an increase in surface area for the two zeolites after treatment, NM-Ca (20.0(1) to 111(4) m2/g) and NV-Na (19.0(4) to 158(7) m2/g). 29Si and 27Al MAS NMR were performed on the natural and treated NV-Na zeolite and the data for the natural NV-Na zeolite suggested a Si:Al ratio of 4.33 similar to that determined by X-Ray fluorescence of 4.55. Removal of lead ions from solution decreased from the native (NM-Ca, 0.27(14), NV-Na, 1.50(17) meq/g) compared to the modified zeolites (30 min HCl treated NM-Ca 0.06(9) and NV-Na, 0.41(23) meq/g) and also decreased upon K+ ion pretreatment in the HCl modified zeolites.


2020 ◽  
Vol 15 (2) ◽  
pp. 525-537 ◽  
Author(s):  
Neza Rahayu Palapa ◽  
Tarmizi Taher ◽  
Bakri Rio Rahayu ◽  
Risfidian Mohadi ◽  
Addy Rachmat ◽  
...  

The preparation of CuAl LDH and biochar (BC) composite derived from rice husk and its application as a low-cost adsorbent for enhanced adsorptive removal of malachite green has been studied. The composite was prepared by a one-step coprecipitation method and characterized by X-ray Diffraction (XRD), Fourier Transform Infra Red (FTIR), Brunauer-Emmett-Teller (BET), and Scanning Electron Microscopy - Energy Dispersive X-ray (SEM−EDX). The result indicated that CuAl LDH was successfully incorporated with the biochar that evidenced by the broadening of XRD peak at 2θ = 24° and the appearance of a new peak at 1095 cm−1 on the FTIR spectra. The BET surface area analysis revealed that CuAl/BC composite exhibited a larger surface area (200.9 m2/g) that the original CuAl LDH (46.2 m2/g). Surface morphological changes also confirmed by SEM image, which showed more aggregated particles. The result of the adsorption study indicated the composite material was efficient in removing malachite green with Langmuir maximum adsorption capacity of CuAl/BC reaching 470.96 mg/g, which is higher than the original CuAl LDH 59.523 mg/g. The thermodynamic analysis suggested that the adsorption of malachite green occurs spontaneously (ΔG < 0 at all tested temperature) and endothermic nature. Moreover, the CuAl/BC composite showed strong potential as a low-cost adsorbent for cationic dye removal since it showed not only a high adsorption capacity but also good reusability. Copyright © 2020 BCREC Group. All rights reserved


2013 ◽  
Vol 785-786 ◽  
pp. 533-536 ◽  
Author(s):  
Shi Bao Li ◽  
Yi Min Zhao ◽  
Jian Feng Zhang ◽  
Cheng Xie ◽  
Dong Mei Li ◽  
...  

A novel PMMA-ZrO2 composite (PZC) was prepared by resin infiltrated to ceramic method. The composite mechanical properties were evaluated and correlated to its microstructure. Partially sintered zirconia ceramics (PSZC) were made by isostatic pressing and partially sintering. Subsequently, the PZC was prepared by vacuum infiltrating prepolymerized MMA into PSZC, followed by in-situ polymerization. When PSZC-70% was used as the matrix, the bending strength, elastic modulus, and fracture toughness of the prepared composite i.e PZC-70% were 202.56±12.09 MPa, 58.71±3.98 GPa, and 4.60±0.26 MPa·m1/2, corresponding to 25.69%, 23.31%, and 169.01% improvement, respectively, in comparison with the control matrix. Among them, the fracture toughness improvement was the most prominent. According to SEM images of the fracture surfaces, each pore of zirconia skeleton was filled by organic resin contributing to the bending strength improvement. These weak interfaces between zirconia skeleton and organic resin absorbed energy and terminated the growth of microcracks which might be responsible for significant improvement in fracture toughness. This PZC material is anticipated to be a new member of the dental CAD/CAM family.


2018 ◽  
Vol 2018 ◽  
pp. 1-14 ◽  
Author(s):  
H. Ait Ahsaine ◽  
Z. Anfar ◽  
M. Zbair ◽  
M. Ezahri ◽  
N. El Alem

Zirconium oxide/activated carbon (Zr3O/AC) composite was synthesized to remove methylene blue (MB) and crystal violet (CV) from the aqueous medium. The Zr3O/AC sample was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analyses (EDS), Raman spectroscopy (RS), BET surface area, and Fourier transform infrared spectroscopy (FTIR). XRD profiles confirmed the successful synthesis of the zirconium oxide/activated carbon composite. SEM images showed multideveloped walls with irregular particle size with channel arrays. The nitrogen physisorption combines I and IV types with a calculated BET surface area of 1095 m2/g. Raman spectrum illustrated a disorder of both crystalline structure and the graphitic structure. The adsorption was better fitted to the pseudo-second-order (PSO) kinetic model. Langmuir model fitted better the experimental results of MB adsorption, whereas the CV was better consistent with the Freundlich model. The obtained results suggested that the MB and CV adsorption might be influenced by the mass transfer that involves multiple diffusion steps. The maximum adsorption capacities are 208.33 and 204.12 mg/g for MB and CV, respectively. The MB and CV removal mechanisms were proposed, and statistical optimization was performed using central composite design combined with the response surface methodology.


2014 ◽  
Vol 926-930 ◽  
pp. 32-35
Author(s):  
Shu Qin Zheng ◽  
Shao Ren ◽  
Jian Ce Zhang ◽  
Wei Zhu

A novel Y zeolite-containing composite material was prepared via in situ crystallization with sepiolite and catalyst residue as starting materials, of which the BET surface area is up to 582 m2/g, the pore volume is 0.43 cm3/g, the relative crystallinity is as high as 55.7 %, the surface is smooth and regular, and Y zeolite particles are in the range of 0.4-1.0 mirons, the composite contains large number Y zeolite with more meso-macro porous structure.The alkalinity in reaction medium has a pronounced effect on the relative crystallinity of Y zeolite.


Author(s):  
Oluwadayo Francis Asokogene ◽  
Muhammad Abbas Ahmad Zaini ◽  
Misau Muhammad Idris ◽  
Surajudeen Abdulsalam ◽  
Aliyu El-Nafaty Usman

Abstract This study was aimed to evaluate the characteristics of chitosan from Pessu river crab shell and its derivatives as prospective adsorbent. The synthesized chitosan (CH) was modified with 10 % (w/v) oxalic acid (CHOx), while the composites (CHOx-ANL1, CHOx-ANL2 and CHOx-ANL3) were designated according to the amount of activated neem leave (ANL). The materials were characterized by Fourier transform infrared (FTIR), energy-dispersive X-ray (EDAX), X-ray diffraction (XRD), scanning electron microscope (SEM), Brunauer-Emmett-Teller (BET), thermal gravimetric (TGA) and methylene blue dye adsorption. The FTIR spectra of chitosan samples show the characteristics of primary and secondary amine/amide groups. The SEM images exhibit a tight, porous and fractured surface, which is covered with activated neem leave for the composites. The BET surface area of chitosan materials is in the increasing order of, CH < CHOx-ANL1 < CHOx-ANL2 < CHOx < CHOx-ANL3. CHOx-ANL3 displays a higher surface area of 389 m2/g, and 70.9 % mesoporosity. Despite its lower surface area of 258 m2/g (65.4 % mesoporosity), CHOx-ANL1 exhibits a greater methylene blue adsorption of 90.8 mg/g at dye concentration of 300 mg/L. The possible removal mechanisms include ionic interaction between dye molecules and functional groups, and surface adsorption due to the textural properties of chitosan samples. Chitosan from Pessu river crab shell and its derivatives are promising adsorbent candidate for dyes and heavy metals removal from water.


1989 ◽  
Vol 175 ◽  
Author(s):  
Toru Nonami

AbstractA biomedical material for use as artificial bone and dental root is provided which takes the form of a sintered composite body comprising a Hydroxyapatite(HAP) and diopside whisker. The mixed powder of HAP and diopside was heated to make this composite material. The sintering of HAP and the precipitation of diopside whisker were examined, to find a method of making them occur simultaneously. Also, diopside was added to HAP and sintering at 1200°C for 2hr. was done. As a result of these investigations, diopside whisker of aspect ratio 101˜15 was formed. Moreover the intermediate layer of CaO-SiO2-P2O5-MgO system was generated at the interface of HAP and whisker. The bending strength of this sintered body was 300MPa and fracture toughness was 3.2MPa ·m1/2. These values were higher by about 2times or 3times than those of matrix HAP respectively. The increase in bending strength was attributed to an increase in fracture toughness, caused by an increase in fracture surface energy.


Fermentation ◽  
2021 ◽  
Vol 7 (2) ◽  
pp. 70
Author(s):  
Wen-Tien Tsai ◽  
Yu-Quan Lin ◽  
Hung-Ju Huang

Rice husk (RH) is one of the most important crop residues around the world, making its valorization an urgent and important topic in recent years. This work focused on the production of RH-based biochars at different pyrolysis temperatures from 400 to 900 °C and holding times from 0 to 90 min. Furthermore, the variations in the yields and pore properties of the resulting biochars were related to these process conditions. The results showed that the pore properties (i.e., BET surface area and porosity) of the resulting RH-based biochar were positively correlated with the ranges of pyrolysis temperature and holding time studied. The maximal pore properties with a BET surface area of around 280 m2/g and porosity of 0.316 can be obtained from the conditions at 900 °C for a holding time of 90 min. According to the data on the nitrogen (N2) adsorption–desorption isotherms and pore size distributions, both microporous and mesoporous structures exist in the resulting biochar. In addition, the EDS and FTIR analyses also supported the slight hydrophilicity on the surface of the RH-based biochar due to the oxygen/silica-containing functional groups. Based on the findings of this work, the RH-based biochar could be used as a material in environmental applications for water conservation, wastewater treatment and soil amendment.


Sign in / Sign up

Export Citation Format

Share Document