Temperature-dependent variable viscosity and thermal conductivity effects on non-Newtonian fluids flow in a porous medium

2022 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ayegbusi Dami Florence
Keyword(s):  
Thermal Conductivity ◽  
Porous Medium ◽  
Iterative Method ◽  
Variable Viscosity ◽  
Newtonian Fluids ◽  
Physical Parameters ◽  
Relaxation Techniques ◽  
Temperature Profiles ◽  
Content Type ◽  
Spectral Relaxation

Purpose The purpose of this paper is to consider the simultaneous flow of Casson Williamson non Newtonian fluids in a vertical porous medium under the influence of variable thermos-physical parameters. Design/methodology/approach The model equations are a set of partial differential equations (PDEs). These PDEs were transformed into a non-dimensionless form using suitable non-dimensional quantities. The transformed equations were solved numerically using an iterative method called spectral relaxation techniques. The spectral relaxation technique is an iterative method that uses the Gauss-Seidel approach in discretizing and linearizing the set of equations. Findings It was found out in the study that a considerable number of variable viscosity parameter leads to decrease in the velocity and temperature profiles. Increase in the variable thermal conductivity parameter degenerates the velocity as well as temperature profiles. Hence, the variable thermo-physical parameters greatly influence the non-Newtonian fluids flow. Originality/value This study considered the simultaneous flow of Casson-Williamson non-Newtonian fluids by considering the fluid thermal properties to vary within the fluid layers. To the best of the author’s knowledge, such study has not been considered in literature.

scholarly journals Atangana-Baleanu and Caputo-Fabrizio Analysis of Fractional Derivatives on MHD Flow past a Moving Vertical Plate with Variable Viscosity and Thermal Conductivity in a Porous Medium

2021 ◽  
Vol 6 (2) ◽  
pp. 493-509
Author(s):  
Dipen Saikia ◽  
Utpal Kumar Saha ◽  
Gopal Chandra Hazarika
Keyword(s):  
Thermal Conductivity ◽  
Porous Medium ◽  
Concentration Distribution ◽  
Fractional Derivatives ◽  
Vertical Plate ◽  
Variable Viscosity ◽  
Mhd Flow ◽  
Iteration Scheme ◽  
Physical Parameters ◽  
Similarity Transformations

In this paper, a numerical investigation is presented for non-integer order derivatives with Atangana-Baleanu (AB) and Caputo-Fabrizio (CF) fractional derivatives for the variable viscosity and thermal conductivity over a moving vertical plate in a porous medium two dimensional free convection unsteady MHD flow. The effects of radiation have also been considered. The governing partial differential equations along with the boundary conditions are changed to ordinary form by similarity transformations. Hence physical parameters show up in the equations and interpretations on these parameters can be achieved suitably.By using ordinary finite difference scheme the equations are discritized and developed in fractional form. These discritized equations are numerically solved by the approach based on Gauss-seidel iteration scheme. Some numerical strategies are used to find the values of AB and CF approaches on time by developing programming code in MATLAB. The effects of all the physical parameters involved in the problem on velocity, temperature and concentration distribution are compared graphically as well as in tabular form. The effects of each parameter are found to be prominent. We have observed a significant variation of values under different parameters using AB and CF approaches on velocity, temperature and concentration distribution with respect to time.

Heat and mass transfer effects on MHD non-Newtonian fluids flow through an inclined thermally-stratified porous medium

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Gladys Tharapatla ◽  
Pamula Rajakumari ◽  
Ramana G.V. Reddy
Keyword(s):  
Mass Transfer ◽  
Porous Medium ◽  
Velocity Profile ◽  
Heat And Mass Transfer ◽  
Newtonian Fluids ◽  
Transfer Effects ◽  
Content Type ◽  
Non Linear ◽  
Homotopy Analysis ◽  
Flow Through

Purpose This paper aims to analyze heat and mass transfer of magnetohydrodynamic (MHD) non-Newtonian fluids flow past an inclined thermally stratified porous plate using a numerical approach. Design/methodology/approach The flow equations are set up with the non-linear free convective term, thermal radiation, nanofluids and Soret–Dufour effects. Thus, the non-linear partial differential equations of the flow analysis were simplified by using similarity transformation to obtain non-linear coupled equations. The set of simplified equations are solved by using the spectral homotopy analysis method (SHAM) and the spectral relaxation method (SRM). SHAM uses the approach of Chebyshev pseudospectral alongside the homotopy analysis. The SRM uses the concept of Gauss-Seidel techniques to the linear system of equations. Findings Findings revealed that a large value of the non-linear convective parameters for both temperature and concentration increases the velocity profile. A large value of the Williamson term is detected to elevate the velocity plot, whereas the Casson parameter degenerates the velocity profile. The thermal radiation was found to elevate both velocity and temperature as its value increases. The imposed magnetic field was found to slow down the fluid velocity by originating the Lorentz force. Originality/value The novelty of this paper is to explore the heat and mass transfer effects on MHD non-Newtonian fluids flow through an inclined thermally-stratified porous medium. The model is formulated in an inclined plate and embedded in a thermally-stratified porous medium which to the best of the knowledge has not been explored before in literature. Two elegance spectral numerical techniques have been used in solving the modeled equations. Both SRM and SHAM were found to be accurate.

Eulerian–Eulerian multi-phase RPI modeling of turbulent forced convective of boiling flow inside the tube with porous medium

2019 ◽  
Vol 30 (5) ◽  
pp. 2739-2757 ◽  
Author(s):  
Reza Azadbakhti ◽  
Farzad Pourfattah ◽  
Abolfazl Ahmadi ◽  
Omid Ali Akbari ◽  
Davood Toghraie
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Reynolds Number ◽  
Porous Medium ◽  
Flow Boiling ◽  
Rensselaer Polytechnic Institute ◽  
Content Type ◽  
Turbulent Flow Regime ◽  
High Reynolds ◽  
Multi Phase

Purpose The purpose of this study is simulation the flow boiling inside a tube in the turbulent flow regime for investigating the effect of using a porous medium in the boiling procedure. Design/methodology/approach To ensure the accuracy of the obtained numerical results, the presented results have been compared with the experimental results, and proper coincidence has been achieved. In this study, the phase change phenomenon of boiling has been modeled by using the Eulerian–Eulerian multi-phase Rensselaer Polytechnic Institute (RPI) wall boiling model. Findings The obtained results indicate using a porous medium in boiling process is very effective in a way that by using a porous medium inside the tub, the location of changing the liquid to the vapor and the creation of bubbles, changes. By increasing the thermal conductivity of porous medium, the onset of phase changing postpones, which causes the enhancement of heat transfer from the wall to the fluid. Generally, it can be said that using a porous medium in boiling flows, especially in flow with high Reynolds numbers, has a positive effect on heat transfer enhancement. Also, the obtained results revealed that by increasing Reynolds number, the created vapor phase along the tube decreases and by increasing Reynolds number, the Nusselt number enhances. Originality/value In present research, by using the computational fluid dynamics, the effect of using a porous medium in the forced boiling of water flow inside a tube has been investigated. The fluid boiling inside the tube has been simulated by using the multi-phase Eulerian RPI wall boiling model, and the effect of thermal conductivity of a porous medium and the Reynolds number on the flow properties, heat transfer and boiling procedure have been investigated.

Modeling and numerical simulation for flow of hybrid nanofluid (SiO2/C3H8O2) and (MoS2/C3H8O2) with entropy optimization and variable viscosity

2019 ◽  
Vol 30 (8) ◽  
pp. 3939-3955 ◽  
Author(s):  
Muhammad Ijaz Khan ◽  
Sohail Ahmad Khan ◽  
Tasawar Hayat ◽  
Muhammad Waqas ◽  
Ahmed Alsaedi
Keyword(s):  
Silicon Dioxide ◽  
Molybdenum Disulfide ◽  
Propylene Glycol ◽  
Variable Viscosity ◽  
Entropy Generation Rate ◽  
Physical Parameters ◽  
Hybrid Nanofluid ◽  
Bejan Number ◽  
Content Type ◽  
Entropy Optimization

Purpose The purpose of this paper is to investigate the entropy optimization in magnetohydrodynamic hybrid nanomaterials flows toward a stretchable surface. The energy expression is modeled subject to dissipation, heat generation/absorption and Joule heating. Here silicon dioxide (SiO2) and molybdenum disulfide (MoS2) as nanoparticles and propylene glycol (C3H8O2) as base fluid, respectively. Furthermore, the authors discussed the comparative study of molybdenum disulfide and silicon dioxide diluted in propylene glycol. The total entropy optimization rate is computed through implementation of the second law of thermodynamics. Design/methodology/approach The nonlinear partial differential system is reduced to an ordinary one through implementation of transformation. Newton built-in shooting method is used for computational results for the given system. Influences of various flow variables on the temperature, Bejan number, velocity, concentration and entropy generation rate are examined graphically for both nanoparticles (SiO2 and MoS2). Gradients of velocity and temperature are computed numerically for various physical parameters. Also, take the comparison between the present and previously published results in tabulated form. Findings For higher estimation of ϕ both temperature and velocity are enhanced. Entropy optimization and Bejan number have the opposite outcome for viscosity parameter. Temperature and velocity have opposite behaviors for larger values of magnetic parameter. Molybdenum disulfide (MoS2) is more efficient than silicon dioxide (SiO2). Originality/value No such work is yet published in the literature.

Non-similar solution of Casson nanofluid with variable viscosity and variable thermal conductivity

2019 ◽  
Vol 30 (8) ◽  
pp. 3919-3938 ◽  
Author(s):  
Ankita Bisht ◽  
Rajesh Sharma
Keyword(s):  
Thermal Conductivity ◽  
Stretching Sheet ◽  
Variable Viscosity ◽  
Variable Thermal Conductivity ◽  
Solar Thermal ◽  
Content Type ◽  
Casson Nanofluid ◽  
Solar Thermal Collectors ◽  
Variation Parameter ◽  
Nonlinear Stretching

Purpose The purpose of this study is to provide a numerical investigation of Casson nanofluid along a vertical nonlinear stretching sheet with variable thermal conductivity and viscosity. Design/methodology/approach The boundary-layer equations are presented in the dimensionless form using proper non-similar transformations. The subsequent non-dimensional nonlinear partial differential equations are solved using the implicit finite difference technique. To linearize the nonlinear terms present in these equations, the quasilinearization technique is used. Findings The investigation showed graphically the temperature, velocity and nanoparticle volume fraction for particular included physical parameters. It is observed that the velocity profile decreases with an increase in the values of Casson fluid parameter while increases with an increase in the viscosity variation parameter. The temperature profile enhances for large values of velocity variation parameter and thermal conductivity parameter while it reduces for large values of thermal buoyancy parameter. Further, the Nusselt number and skin-friction coefficient are introduced which are helpful in determining the physical aspects of Casson nanofluid flow. Practical implications The immediate control of heat transfer in the industrial system is crucial because of increasing energy prices. Recently, nanotechnology is proposed to control the heat transfer phenomenon. Ongoing research in complex nanofluid has been fruitful in various applications such as solar thermal collectors, nuclear reactors, electronic equipment and diesel–electric conductor. A reasonable amount of nanoparticle when added to the base fluid in solar thermal collectors serves to deeper absorption of incident radiation, and hence it upgrades the efficiency of the solar thermal collectors. Originality/value The non-similar solution of Casson nanofluid due to a vertical nonlinear stretching sheet with variable viscosity and thermal conductivity is discussed in this work.

MHD slip flow and convective heat transfer due to a moving plate with effects of variable viscosity and thermal conductivity

2020 ◽  
Vol 16 (5) ◽  
pp. 991-1018
Author(s):  
Mahantesh M. Nandeppanavar ◽  
M.C. Kemparaju ◽  
R. Madhusudhan ◽  
S. Vaishali
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Boundary Layer ◽  
Differential Equations ◽  
Radiation Effects ◽  
Variable Viscosity ◽  
Heat Transfer Analysis ◽  
Concentration Profiles ◽  
Moving Plate ◽  
Content Type

PurposeThe steady two-dimensional laminar boundary layer flow, heat and mass transfer over a flat plate with convective surface heat flux was considered. The governing nonlinear partial differential equations were transformed into a system of nonlinear ordinary differential equations and then solved numerically by Runge–Kutta method with the most efficient shooting technique. Then, the effect of variable viscosity and variable thermal conductivity on the fluid flow with thermal radiation effects and viscous dissipation was studied. Velocity, temperature and concentration profiles respectively were plotted for various values of pertinent parameters. It was found that the momentum slip acts as a boost for enhancement of the velocity profile in the boundary layer region, whereas temperature and concentration profiles decelerate with the momentum slip.Design/methodology/approachNumerical Solution is applied to find the solution of the boundary value problem.FindingsVelocity, heat transfer analysis is done with comparing earlier results for some standard cases.Originality/value100

Lattice Boltzmann Simulations for Thermal Conductivity Estimation in Heterogeneous Materials

2009 ◽  
Vol 283-286 ◽  
pp. 364-369 ◽  
Author(s):  
M.R. Arab ◽  
Bernard Pateyron ◽  
Mohammed El Ganaoui ◽  
Nicolas Calvé
Keyword(s):  
Thermal Conductivity ◽  
Porous Medium ◽  
Lattice Boltzmann ◽  
Numerical Study ◽  
Theoretical Models ◽  
Short Description ◽  
Physical Parameters ◽  
Two Dimensional ◽  
Lattice Boltzmann Simulations ◽  
Boltzmann Method

For simulating flows in a porous medium, a numerical tool based on the Lattice Boltzmann Method (LBM) is developed with regards to the classical D2Q9 model. A short description of this model is presented. This technique, applied to two-dimensional configurations, indicates its ability to simulate phenomena of heat and mass transfer. The numerical study is extended to estimate physical parameters that characterize porous materials, like the so-called Effective Thermal Conductivity (ETC) which is of our interest in this paper. Obtained results are compared with those which could be found analytically and by theoretical models. Finally, a porous medium is considered to find its ETC.

Sign in / Sign up

Export Citation Format

Share Document