Measurement of Structural Stiffness and Damping Coefficients in a Metal Mesh Foil Bearing

2009 ◽  
Vol 132 (3) ◽  
Author(s):  
Luis San Andrés ◽  
Thomas Abraham Chirathadam ◽  
Tae-Ho Kim
Keyword(s):  
Loss Factor ◽  
Copper Wire ◽  
Mechanical Energy ◽  
Excitation Frequency ◽  
Viscous Damping ◽  
Structural Stiffness ◽  
Metal Mesh ◽  
Equivalent Viscous Damping ◽  
Damping Coefficients ◽  
Stiffness And Damping

Engineered metal mesh foil bearings (MMFBs) are a promising low cost bearing technology for oil-free microturbomachinery. In a MMFB, a ring shaped metal mesh provides a soft elastic support to a smooth arcuate foil wrapped around a rotating shaft. This paper details the construction of a MMFB and the static and dynamic load tests conducted on the bearing for estimation of its structural stiffness and equivalent viscous damping. The 28.00 mm diameter 28.05 mm long bearing, with a metal mesh ring made of 0.3 mm copper wire and compactness of 20%, is installed on a test shaft with a slight preload. Static load versus bearing deflection measurements display a cubic nonlinearity with large hysteresis. The bearing deflection varies linearly during loading, but nonlinearly during the unloading process. An electromagnetic shaker applies on the test bearing loads of controlled amplitude over a frequency range. In the frequency domain, the ratio of applied force to bearing deflection gives the bearing mechanical impedance, whose real part and imaginary part give the structural stiffness and damping coefficients, respectively. As with prior art published in the literature, the bearing stiffness decreases significantly with the amplitude of motion and shows a gradual increasing trend with frequency. The bearing equivalent viscous damping is inversely proportional to the excitation frequency and motion amplitude. Hence, it is best to describe the mechanical energy dissipation characteristics of the MMFB with a structural loss factor (material damping). The experimental results show a loss factor as high as 0.7 though dependent on the amplitude of motion. Empirically based formulas, originally developed for metal mesh rings, predict bearing structural stiffness and damping coefficients that agree well with the experimentally estimated parameters. Note, however, that the metal mesh ring, after continuous operation and various dismantling and re-assembly processes, showed significant creep or sag that resulted in a gradual decrease in its structural force coefficients.

Measurement of Structural Stiffness and Damping Coefficients in a Metal Mesh Foil Bearing

2009 ◽  
Author(s):  
Luis San Andre´s ◽  
Thomas Abraham Chirathadam ◽  
Tae-Ho Kim
Keyword(s):  
Loss Factor ◽  
Copper Wire ◽  
Mechanical Energy ◽  
Excitation Frequency ◽  
Viscous Damping ◽  
Structural Stiffness ◽  
Metal Mesh ◽  
Equivalent Viscous Damping ◽  
Damping Coefficients ◽  
Stiffness And Damping

Engineered Metal Mesh Foil Bearings (MMFB) are a promising low cost bearing technology for oil-free microturbomachinery. In a MMFB, a ring shaped metal mesh (MM) provides a soft elastic support to a smooth arcuate foil wrapped around a rotating shaft. The paper details the construction of a MMFB and the static and dynamic load tests conducted on the bearing for estimation of its structural stiffness and equivalent viscous damping. The 28.00 mm diameter, 28.05 mm long bearing, with a metal mesh ring made of 0.3 mm Copper wire and compactness of 20%, is installed on a test shaft with a slight preload. Static load versus bearing deflection measurements display a cubic nonlinearity with large hysteresis. The bearing deflection varies linearly during loading, but nonlinearly during the unloading process. An electromagnetic shaker applies on the test bearing loads of controlled amplitude over a frequency range. In the frequency domain, the ratio of applied force to bearing deflection gives the bearing mechanical impedance, whose real part and imaginary part give the structural stiffness and damping coefficients, respectively. As with prior art published in the literature, the bearing stiffness decreases significantly with the amplitude of motion and shows a gradual increasing trend with frequency. The bearing equivalent viscous damping is inversely proportional to the excitation frequency and motion amplitude. Hence, it is best to describe the mechanical energy dissipation characteristics of the MMFB with a structural loss factor (material damping). The experimental results show a loss factor as high as 0.7 though dependent on the amplitude of motion. Empirically based formulas, originally developed for metal mesh rings, predict bearing structural stiffness and damping coefficients agreeing well with the experimentally estimated parameters. Note, however, that the metal mesh ring, after continuous operation and various dismantling and reassembly processes, showed significant creep or sag that resulted in a gradual decrease of its structural force coefficients.

Structural and Rotordynamic Force Coefficients of a Shimmed Bump Foil Bearing: An Assessment of a Simple Engineering Practice

2015 ◽  
Vol 138 (1) ◽  
Author(s):  
Luis San Andrés ◽  
Joshua Norsworthy
Keyword(s):  
Loss Factor ◽  
High Speed ◽  
Static Load ◽  
Low Cost ◽  
Mechanical Energy ◽  
Excitation Frequency ◽  
Engineering Practice ◽  
Force Coefficients ◽  
Damping Coefficients ◽  
Stiffness And Damping

High speed rotors supported on bump-type foil bearings (BFBs) often suffer from large subsynchronous whirl motions. Mechanically preloading BFBs through shimming is a common, low cost practice that shows improvements in rotordynamic stability. However, there is an absence of empirical information related to the force coefficients (structural and rotordynamic) of shimmed BFBs. This paper details a concerted study toward assessing the effect of shimming on a first generation BFB (L = 38.1 mm and D = 36.5 mm). Three metal shims, 120 deg apart, are glued to the inner surface of the bearing cartridge and facing the underside of the bump foil strip. The shim sets are of identical thickness, either 30 μm or 50 μm. In static load tests, a bearing with shims shows a (nonlinear) structural stiffness larger than for the bearing without shims. Torque measurements during shaft acceleration also demonstrate a shimmed BFB has a larger friction coefficient. For a static load of 14.3 kPa, dynamic loads with a frequency sweep from 250 Hz to 450 Hz are exerted on the BFB, without and with shims, to estimate its rotordynamic force coefficients while operating at ∼50 krpm (833 Hz). Similar measurements are conducted without shaft rotation. Results are presented for the original BFB (without shims) and the two shimmed BFB configurations. The direct stiffnesses of the BFB, shimmed or not, increase with excitation frequency, thus evidencing a mild hardening effect. The BFB stiffness and damping coefficients decrease slightly for operation with rotor speed as opposed to the coefficients when the shaft is stationary. For frequencies above 300 Hz, the direct damping coefficients of the BFB with 50 μm thick shims are ∼30% larger than the coefficients of the original bearing. The bearing structural loss factor, a measure of its ability to dissipate mechanical energy, is derived from the direct stiffness and damping coefficients. The BFB with 50 μm thick shims has a 25% larger loss factor—average from test data collected at 300 Hz to 400 Hz—than the original BFB. Further measurements of rotor motions while the shaft accelerates to ∼50 krpm demonstrate the shimmed BFB (thickest shim set) effectively removes subsynchronous whirl motions amplitudes that were conspicuous when operating with the original bearing.

Structural and Rotordynamic Force Coefficients of a Shimmed Bump Foil Bearing: An Assessment of a Simple Engineering Practice

2015 ◽  
Author(s):  
Luis San Andrés ◽  
Joshua Norsworthy
Keyword(s):  
Loss Factor ◽  
High Speed ◽  
Static Load ◽  
Low Cost ◽  
Mechanical Energy ◽  
Excitation Frequency ◽  
Engineering Practice ◽  
Force Coefficients ◽  
Damping Coefficients ◽  
Stiffness And Damping

High speed rotors supported on bump-type foil bearings (BFBs) often suffer from large sub synchronous whirl motions. Mechanically preloading BFBs through shimming is a common, low cost practice that shows improvements in rotordynamic stability. However, there is absence of empirical information related to the force coefficients (structural and rotordynamic) of shimmed BFBs. This paper details a concerted study towards assessing the effect of shimming on a first generation BFB (L=38.1 mm, D =36.5 mm). Three metal shims, 120° apart, are glued to the inner surface of the bearing cartridge and facing the underside of the bump foil strip. The shim sets are of identical thickness, either 30 μm or 50 μm. Static load tests show that shimming produces nonlinear static load vs. deflection curves leading to a larger structural stiffness than for the bearing without shims. Torque measurements during shaft acceleration also demonstrate a shimmed BFB has a larger friction coefficient. For a static load of 14.3 kPa, dynamic loads with a frequency sweep from 250 Hz to 450 Hz are exerted on the BFB, without and with shims, to estimate its rotordynamic force coefficients while operating at ∼50 krpm (833 Hz). Similar measurements are conducted without shaft rotation. Results are presented for the original BFB (without shims) and the two shimmed BFB configurations. The direct stiffnesses of the BFB, shimmed or not, increase with excitation frequency thus evidencing a mild hardening effect. The BFB stiffness and damping coefficients decrease slightly for operation with rotor speed as opposed to the coefficients when the shaft is stationary. For frequencies above 300 Hz, the direct damping coefficients of the BFB with 50 μm thick shims are ∼ 30% larger than the coefficients of the original bearing. The bearing structural loss factor, a measure of its ability to dissipate mechanical energy, is derived from the direct stiffness and damping coefficients. The BFB with 50 μm thick shims has a 25% larger loss factor — average from test data collected at 300 Hz to 400 Hz — than the original BFB. Further measurements of rotor motions while the shaft accelerates to ∼50 krpm demonstrate the shimmed BFB (thickest shim set) effectively removes sub synchronous whirl motions amplitudes that were conspicuous when operating with the original bearing.

Design and structural performance measurements of a novel multi-cantilever foil bearing

2014 ◽  
Vol 229 (10) ◽  
pp. 1830-1838 ◽  
Author(s):  
Kai Feng ◽  
Xueyuan Zhao ◽  
Zhiyang Guo
Keyword(s):  
Dynamic Characteristics ◽  
Dynamic Load ◽  
Dynamic Stiffness ◽  
Excitation Frequency ◽  
Viscous Damping ◽  
Equivalent Viscous Damping ◽  
Foil Bearing ◽  
Load Tests ◽  
Stiffness And Damping ◽  
Motion Amplitude

With increasing need for high-speed, high-temperature, and oil-free turbomachinery, gas foil bearings (GFBs) have been considered to be the best substitutes for traditional oil-lubricated bearings. A multi-cantilever foil bearing (MCFB), a novel GFB with multi-cantilever foil strips serving as the compliant underlying structure, was designed, fabricated, and tested. A series of static and dynamic load tests were conducted to measure the structural stiffness and equivalent viscous damping of the prototype MCFB. Experiments of static load versus deflection showed that the proposed bearing has a large mechanical energy dissipation capability and a pronounced nonlinear static stiffness that can prevents overly large motion amplitude of journal. Dynamic load tests evaluated the influence of motion amplitude, loading orientation and misalignment on the dynamic stiffness and equivalent viscous damping with respect to excitation frequency. The test results demonstrated that the dynamic stiffness and damping are strongly dependent on the excitation frequency. Three motion amplitudes were applied to the bearing housing to investigate the effects of motion amplitude on the dynamic characteristics. It is noted that the bearing dynamic stiffness and damping decreases with incrementally increasing motion amplitudes. A high level of misalignment can lead to larger static and dynamic bearing stiffness as well as to larger equivalent viscous damping. With dynamic loads applied to two orientations in the bearing midplane separately, the dynamic stiffness increases rapidly and the equivalent viscous damping declines slightly. These results indicate that the loading orientation is a non-negligible factor on the dynamic characteristics of MCFBs.

Experimental Evaluation of the Structure Characterization of a Novel Hybrid Bump-Metal Mesh Foil Bearing

2015 ◽  
Vol 138 (2) ◽  
Author(s):  
Kai Feng ◽  
Yuman Liu ◽  
Xueyuan Zhao ◽  
Wanhui Liu
Keyword(s):  
Excitation Frequency ◽  
Structure Characterization ◽  
Viscous Damping ◽  
Metal Mesh ◽  
Equivalent Viscous Damping ◽  
Foil Bearings ◽  
Damping Characteristics ◽  
Foil Bearing ◽  
Mesh Density ◽  
Load Tests

Rotors supported by gas foil bearings (GFBs) experience stability problem caused by subsynchronous vibrations. To obtain a GFB with satisfactory damping characteristics, this study presented a novel hybrid bump-metal mesh foil bearing (HB-MMFB) that consists of a bump foil and metal mesh blocks in an underlying supporting structure, which takes advantage of both bump-type foil bearings (BFBs) and MMFBs. A test rig with a nonrotating shaft was designed to estimate structure characterization. Results from the static load tests show that the proposed HB-MFBs exhibit an excellent damping level compared with the BFBs with a similar size because of the countless microslips in the metal mesh blocks. In the dynamic load tests, the HB-MFB with a metal mesh density of 36% presents a viscous damping coefficient that is approximately twice that of the test BFB. The dynamics structural coefficients of HB-MFBs, including structural stiffness, equivalent viscous damping, and structural loss factor, are all dependent on excitation frequency and motion amplitude. Moreover, they exhibit an obvious decrease with the decline in metal mesh density.

Structural Stiffness and Damping Coefficients of a Multileaf Foil Bearing With Bump Foils Underneath

2013 ◽  
Vol 136 (4) ◽  
Author(s):  
Ye Tian ◽  
Yanhua Sun ◽  
Lie Yu
Keyword(s):  
Excitation Frequency ◽  
Magnetic Bearing ◽  
Damping Capacity ◽  
Structural Stiffness ◽  
Test Rig ◽  
Domain Identification ◽  
Damping Coefficients ◽  
Foil Bearing ◽  
Applied Forces ◽  
Stiffness And Damping

This paper presents a multileaf foil bearing (MLFB), which consists of four resilient top foils and four stiff bump foils underneath; thus, a high supporting capacity and a high damping capacity can be achieved. A specially designed test rig is used to identify the structural stiffness and damping coefficients of the MLFB. The rotor of the test rig is supported by two journal MLFBs and a thrust active magnetic bearing (AMB) and the static and dynamic loads are applied by two radial AMBs. The tests on MLFBs were conducted under conditions of no shaft rotation at different angular positions and journal displacements with different excitation frequency. A frequency domain identification method is presented to determine the stiffness and damping coefficients. Static measurements show nonlinear deflections with applied forces, which varies with the orientation of the load angular position. The dynamic measurements show that the stiffness and equivalent viscous damping change with the excitation frequency. Furthermore, the stiffness and damping coefficients are related to the operating position where dynamic load tests were conducted. The investigation provides extensive measurements of the static and dynamic characteristics of the MLFB. These results can serve as a benchmark for the calibration of analytical tools under development.

Hermetically Sealed Squeeze Film Damper for Operation in Oil-Free Environments

2018 ◽  
Vol 141 (2) ◽  
Author(s):  
Bugra Ertas ◽  
Adolfo Delgado
Keyword(s):  
Excitation Frequency ◽  
Squeeze Film ◽  
Force Density ◽  
Viscous Damping ◽  
Squeeze Film Damper ◽  
Open Flow ◽  
Damping Coefficients ◽  
End Plate ◽  
Stiffness And Damping ◽  
Gas Bearing

The following work advances a new concept for a hermetically sealed squeeze film damper (HSFD), which does not require an open-flow lubrication system. The hermetically sealed concept utilizes a submersed plunger within a contained fluidic cavity filled with incompressible fluid and carefully controlled end plate clearances to generate high levels of viscous damping. Although the application space for a hermetic damper can be envisioned to be quite broad, the context here will target the use of this device as a rotordynamic bearing support damper in flexibly mounted gas bearing systems. The effort focused on identifying the stiffness and damping behavior of the damper while varying test parameters such as excitation frequency, vibration amplitude, and end plate clearance. To gain further insight to the damper behavior, key dynamic pressure measurements in the damper land were used for identifying the onset conditions for squeeze film cavitation. The HSFD performance is compared to existing gas bearing support dampers and a conventional open-flow squeeze film dampers (SFD) used in turbomachinery. The damper concept yields high viscous damping coefficients an order of magnitude larger than existing oil-free gas bearing supports dampers and shows comparable damping levels to current state of the art open-flow SFD. The force coefficients were shown to contribute frequency-dependent stiffness and damping coefficients while exhibiting amplitude independent behavior within operating regimes without cavitation. Finally, using experimentally based force density calculations, the data revealed threshold cavitation velocities, approximated for the three end seal clearance cases. To complement the experimental work, a Reynolds-based fluid flow model was developed and is compared to the HSFD damping and stiffness results.

Metal Mesh Foil Bearing: Effect of Motion Amplitude, Rotor Speed, Static Load, and Excitation Frequency on Force Coefficients

2011 ◽  
Vol 133 (12) ◽  
Author(s):  
Luis San Andrés ◽  
Thomas Abraham Chirathadam
Keyword(s):  
Energy Dissipation ◽  
High Speed ◽  
Mechanical Energy ◽  
Excitation Frequency ◽  
Wire Mesh ◽  
Test Element ◽  
Metal Mesh ◽  
Force Coefficients ◽  
Damping Coefficients ◽  
Mechanical Energy Dissipation

Metal mesh foil bearings (MMFBs), simple to construct and inexpensive, are a promising bearing technology for oil-free microturbomachinery operating at high speed and high temperature. Prior research demonstrated the near friction-free operation of a MMFB operating to 60 krpm and showing substantial mechanical energy dissipation characteristics. This paper details further experimental work and reports MMFB rotordynamic force coefficients. The test rig comprises a turbocharger driven shaft and overhung journal onto which a MMFB is installed. A soft elastic support structure akin to a squirrel cage holds the bearing, aiding to its accurate positioning relative to the journal. Two orthogonally positioned shakers excite the test element via stingers. The test bearing comprises a cartridge holding a Copper wire mesh ring, 2.7 mm thick, and a top arcuate foil. The bearing length and inner diameter are 38 mm and 36.5 mm, respectively. Experiments were conducted with no rotation and with journal spinning at 40–50 krpm, with static loads of 22 N and 36 N acting on the bearing. Dynamic load tests spanning frequencies from 150 to 450 Hz were conducted while keeping the amplitude of bearing displacements at 20 µm, 25 µm, and 30 µm. With no journal spinning, the force coefficients represent the bearing elastic structure alone because the journal and bearing are in contact. The direct stiffnesses gradually increase with frequency while the direct damping coefficients drop quickly at low frequencies (< 200 Hz) and level off above this frequency. The damping combines both viscous and material types from the gas film and mesh structure. Journal rotation induces airborne operation with a hydrodynamic gas film separating the rotor from its bearing. Hence, cross-coupled stiffness coefficients appear although with magnitudes lower than those of the direct stiffnesses. The direct stiffnesses, 0.4 to 0.6 MN/m within 200–400 Hz, are slightly lower in magnitude as those obtained without journal rotation, suggesting the air film stiffness is quite high. Bearing direct stiffnesses are inversely proportional to the bearing motion amplitudes, whereas the direct equivalent viscous damping coefficients do not show any noticeable variation. All measurements evidence a test bearing system with material loss factor (γ) ∼ 1.0, indicating significant mechanical energy dissipation ability.

Experimental Structural Stiffness and Damping in a 2nd Generation Foil Bearing for Increasing Shaft Temperatures

2009 ◽  
Author(s):  
Luis San Andre´s ◽  
Keun Ryu
Keyword(s):  
Structural Parameters ◽  
Mechanical Energy ◽  
Excitation Frequency ◽  
Electric Heater ◽  
Structural Stiffness ◽  
Hollow Shaft ◽  
2Nd Generation ◽  
Foil Bearing ◽  
Structural Loss ◽  
Stiffness And Damping

Demonstrated gas foil bearing (GFB) operation at high temperature is of interest for gas turbine applications. The effects of (high) shaft temperature on the structural stiffness and damping parameters of a foil bearing must be assessed experimentally. Presently, a hollow shaft warmed by an electric heater holds a floating 2nd generation FB that is loaded dynamically by an electromagnetic shaker. In tests with the shaft temperature up to 184°C, the measurements of dynamic load and ensuing FB deflection render the bearing structural parameters, stiffness and damping, as a function of excitation frequency and amplitude of motion. The identified FB stiffness and viscous damping coefficients increase with shaft temperature due to a reduction in the FB clearance. The bearing material structural loss factor, best representing mechanical energy dissipation, decreases slightly with shaft temperature while increasing with excitation frequency.

Hermetically Sealed Squeeze Film Damper for Operation in Oil-Free Environments

2018 ◽  
Author(s):  
Bugra Ertas ◽  
Adolfo Delgado
Keyword(s):  
Excitation Frequency ◽  
Squeeze Film ◽  
Force Density ◽  
Viscous Damping ◽  
Squeeze Film Damper ◽  
Open Flow ◽  
Damping Coefficients ◽  
End Plate ◽  
Stiffness And Damping ◽  
Gas Bearing

The following work advances a new concept for a hermetically sealed squeeze film damper (HSFD), which does not require an open-flow lubrication system. The hermetically sealed concept utilizes a submersed plunger within a contained fluidic cavity filled with incompressible fluid and carefully controlled end plate clearances to generate high levels of viscous damping. Although the application space for a hermetic damper can be envisioned to be quite broad, the context here will target the use of this device as a rotordynamic bearing support damper in flexibly mounted gas bearing systems. The effort focused on identifying the stiffness and damping behavior of the damper while varying test parameters such as excitation frequency, vibration amplitude, and end plate clearance. To gain further insight to the damper behavior, key dynamic pressure measurements in the damper land were used for identifying the onset conditions for squeeze film cavitation. The HSFD performance is compared to existing gas bearing support dampers and a conventional open-flow squeeze film dampers (SFD) used in turbomachinery. The damper concept yields high viscous damping coefficients an order of magnitude larger than existing oil-free gas bearing supports dampers and shows comparable damping levels to current state of the art open-flow SFD. The force coefficients were shown to contribute frequency dependent stiffness and damping coefficients while exhibiting amplitude independent behavior within operating regimes without cavitation. Finally, using experimentally based force density calculations the data revealed threshold cavitation velocities, approximated for the three end seal clearance cases. To complement the experimental work, a Reynolds based fluid flow model was developed and is compared to the HSFD damping and stiffness results.

Sign in / Sign up

Export Citation Format

Share Document