Numerical and Experimental Analysis of 3D Micro-Corrugated Wing in Gliding Flight

2021 ◽  
Author(s):  
Nasim Chitsaz ◽  
Kamran Siddiqui ◽  
Romeo Marian ◽  
Javaan S. Chahl
Keyword(s):  
Stokes Equations ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Aerodynamic Performance ◽  
Numerical Results ◽  
Three Dimensional Model ◽  
Wing Model ◽  
Computational Fluid Dynamics Analysis ◽  
Gliding Flight ◽  
Flat Profile

Abstract In this study, computational fluid dynamics analysis was performed on a three-dimensional model of a Libellulidae wing to determine aerodynamic performance in gliding flight. The wing is comprised of various corrugated features alongside the spanwise and chordwise directions, as well as twist. The detailed features of real 3D dragonfly wing models, including all the corrugations through both span and chord, have not been considered in the past for a detailed aerodynamic analysis. The simulations were conducted by solving the Navier-Stokes equations to demonstrate gliding performance over a range of angles of attack at low Reynolds numbers. The numerical model was validated against experimental data obtained from a fabricated corrugated wing model using particle image velocimetry. The numerical results demonstrate that bio-inspired wings with corrugations compared to flat profile wings generate more lift with lower drag, trapping the vortices in the valleys of wing corrugation leading to delayed flow separation and delayed stall. The experimental and numerical results demonstrate that the methodology presented in this study can be used to measure bio-inspired 3D wing flow characteristics, including the influence of complex corrugations on aerodynamic performance. These findings contribute to the advancement of knowledge required for designing an optimized bioinspired micro air vehicle.

Effects of stator splitter blades on aerodynamic performance of a single-stage transonic axial compressor

2020 ◽  
Vol 14 (4) ◽  
pp. 7369-7378
Author(s):  
Ky-Quang Pham ◽  
Xuan-Truong Le ◽  
Cong-Truong Dinh
Keyword(s):  
Stokes Equations ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Aerodynamic Performance ◽  
Numerical Results ◽  
Single Stage ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Operating Stability ◽  
Length Coverage

Splitter blades located between stator blades in a single-stage axial compressor were proposed and investigated in this work to find their effects on aerodynamic performance and operating stability. Aerodynamic performance of the compressor was evaluated using three-dimensional Reynolds-averaged Navier-Stokes equations using the k-e turbulence model with a scalable wall function. The numerical results for the typical performance parameters without stator splitter blades were validated in comparison with experimental data. The numerical results of a parametric study using four geometric parameters (chord length, coverage angle, height and position) of the stator splitter blades showed that the operational stability of the single-stage axial compressor enhances remarkably using the stator splitter blades. The splitters were effective in suppressing flow separation in the stator domain of the compressor at near-stall condition which affects considerably the aerodynamic performance of the compressor.

scholarly journals A computational study of the aerodynamic performance of a dragonfly forewing in gliding flight

2018 ◽  
Vol 151 ◽  
pp. 03001 ◽  
Author(s):  
Huixiang Liu ◽  
Guoyi He ◽  
Chengyu Ma ◽  
Qi Wang ◽  
Yun Luo
Keyword(s):  
Flat Plate ◽  
Computational Study ◽  
Large Angle ◽  
Three Dimensional ◽  
Aerodynamic Performance ◽  
Three Dimensional Model ◽  
Dragonfly Wing ◽  
Gliding Flight ◽  
Positive Effect ◽  
Better Than

Gliding flight is a common mode of flight for dragonfly, the objective of the current research is to use numerical simulations to explore whether the corrugations have positive effect on aerodynamic performance of the dragonfly wings in gliding flight. In order to compare aerodynamic performance of the dragonfly wing and flat plate, a three-dimensional model of the dragonfly forewing and a three-dimensional flat plate with the same shape of the dragonfly forewing are established. The flow fields around three-dimensional dragonfly forewing and flat plate are simulated for Re=10000 and angles of attack changing from 0° to 25°(with an interval of 5°), numerical simulation indicate that aerodynamic performance of the dragonfly wing is slightly better than the flat plate over the entire range of parameters tested, especially the effect of the corrugateions on the flow is more evident at large angle of attack.

Effects of a Circumferential Feed-Back Channel on Aerodynamic Performance of a Single-Stage Transonic Axial Compressor

2017 ◽  
Author(s):  
Cong-Truong Dinh ◽  
Sang-Bum Ma ◽  
Kwang-Yong Kim
Keyword(s):  
Stokes Equations ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Aerodynamic Performance ◽  
Numerical Results ◽  
Single Stage ◽  
Navier Stokes ◽  
Channel Inlet ◽  
Navier Stokes Equations ◽  
Stall Margin

This paper presents an investigation of a circumferential feed-back channel located on shroud surface in rotor domain to find its effects on aerodynamic performance of a single-stage axial compressor, NASA Stage 37, using three-dimensional Reynolds-averaged Navier-Stokes equations. Validation of numerical results was performed using experimental data for both of single rotor and single-stage compressors. A parametric study of the feed-back channel was performed using various geometric parameters related to the locations and shapes of the channel inlet and outlet. The numerical results showed that a reference circumferential feed-back channel increased the stall margin by 26.8% with 0.14% reduction in the peak adiabatic efficiency, compared to the case without the feed-back channel.

3-D Model of Proton Exchange Membrane Fuel Cells

2000 ◽  
Author(s):  
Tianhong Zhou ◽  
Hongtan Liu
Keyword(s):  
Fuel Cell ◽  
Proton Exchange Membrane ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Pem Fuel Cell ◽  
Proton Exchange ◽  
Three Dimensional Model ◽  
Chemical Reaction Kinetics ◽  
Fuel Cell Performance ◽  
D Model

Abstract A comprehensive three-dimensional model for a proton exchanger membrane (PEM) fuel cell is developed to evaluate the effects of various design and operating parameters on fuel cell performance. The geometrical model includes two distinct flow channels separated by the membrane and electrode assembly (MEA). This model is developed by coupling the governing equations for reactant mass transport and chemical reaction kinetics. To facilitate the numerical solution, the full PEM fuel cell was divided into three coupled domains according to the flow characteristics. The 3-D model has been applied to study species transport, heat transfer, and current density distributions within a fuel cell. The predicated polarization behavior is shown to compare well with experimental data from the literature. The modeling results demonstrate good potential for this computational model to be used in operation simulation as well as design optimization.

Numerical simulation of boundary-layer transition and transition control

1989 ◽  
Vol 199 ◽  
pp. 403-440 ◽  
Author(s):  
E. Laurien ◽  
L. Kleiser
Keyword(s):  
Boundary Layer ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Transition Process ◽  
Numerical Results ◽  
Boundary Layer Transition ◽  
Two Dimensional ◽  
Layer Transition ◽  
Longitudinal Vortices ◽  
Tollmien Schlichting

The laminar-turbulent transition process in a parallel boundary-layer with Blasius profile is simulated by numerical integration of the three-dimensional incompressible Navier-Stokes equations using a spectral method. The model of spatially periodic disturbances developing in time is used. Both the classical Klebanoff-type and the subharmonic type of transition are simulated. Maps of the three-dimensional velocity and vorticity fields and visualizations by integrated fluid markers are obtained. The numerical results are compared with experimental measurements and flow visualizations by other authors. Good qualitative and quantitative agreement is found at corresponding stages of development up to the one-spike stage. After the appearance of two-dimensional Tollmien-Schlichting waves of sufficiently large amplitude an increasing three-dimensionality is observed. In particular, a peak-valley structure of the velocity fluctuations, mean longitudinal vortices and sharp spike-like instantaneous velocity signals are formed. The flow field is dominated by a three-dimensional horseshoe vortex system connected with free high-shear layers. Visualizations by time-lines show the formation of A-structures. Our numerical results connect various observations obtained with different experimental techniques. The initial three-dimensional steps of the transition process are consistent with the linear theory of secondary instability. In the later stages nonlinear interactions of the disturbance modes and the production of higher harmonics are essential.We also study the control of transition by local two-dimensional suction and blowing at the wall. It is shown that transition can be delayed or accelerated by superposing disturbances which are out of phase or in phase with oncoming Tollmien-Schlichting instability waves, respectively. Control is only effective if applied at an early, two-dimensional stage of transition. Mean longitudinal vortices remain even after successful control of the fluctuations.

A Conceptual Model of Flapping-Wing Mechanism Inspired from the Results of Numerical Study

2013 ◽  
Vol 397-400 ◽  
pp. 783-788
Author(s):  
Xing Wei Zhang ◽  
Chao Wang ◽  
Hang Liu
Keyword(s):  
Conceptual Model ◽  
Power Efficiency ◽  
Stokes Equations ◽  
Numerical Study ◽  
Flapping Wing ◽  
Numerical Results ◽  
Navier Stokes ◽  
Active Deformation ◽  
Navier Stokes Equations ◽  
Wing Model

This paper investigates the aerodynamic forces of several plunging wing models by means of computational fluid dynamics. A finite volume method was used to solve the two-dimensional unsteady incompressible Navier-Stokes equations. The forces and power efficiency have been calculated and compared between sets of different models. Current work found that the nonsymmetrical moving can enhance the lift and thrust forces. The numerical results also prove that the flexible wing model can be use to improve the efficiency and reduce the input. Additionally, a new conceptual model for flapping wing mechanism with active deformation and adaptive nonsymmetrical driving motion is proposed base on the numerical results.

scholarly journals AERODYNAMICS OF JETS INTERACTING WITH A FLAT SURFACE

2019 ◽  
Vol 62 (4) ◽  
pp. 263-269
Author(s):  
I. A. Pribytkov ◽  
S. I. Kondrashenko
Keyword(s):  
Heat Transfer ◽  
Critical Point ◽  
Flat Surface ◽  
Stokes Equations ◽  
Thermal State ◽  
Exchange Process ◽  
Three Dimensional ◽  
Internal Diameter ◽  
Three Dimensional Model ◽  
Aerodynamic Properties

In this paper, the development features of a single free jet of hightemperature nitrogen interacting with a flat surface were studied. Calculation of the heat exchange process during heating by the attacking jets is very difficult to implement analytically due to complexity of the gas-dynamic processes occurring both in a single jet and in a system of jets interacting with the metal. The computational difficulties are aggravated by the fact that when interacting with the surface the jet as such disappears. The flat (fan) flow interacts with the surface: form, aerodynamic properties and thermal state of the flow strongly differ from those of the original jet. The studies were conducted on the basis of numerical simulation in the FloEFD software and computing complex for multiphysical simulation based on solution of the equations of gas dynamics and heat transfer. The solved system of equations consisted of Navier-Stokes equations, equations of energy and continuity and was supplemented by k – ε turbulence model. A three-dimensional model was developed for simulation, the necessary properties, initial and boundary conditions were specified. In the study of aerodynamics of a single high-temperature jet interacting with the surface, the main defining values were: nitrogen flow rate from the nozzle U0 , nitrogen temperature T, internal diameter of the nozzle d0 , distance from the nozzle section to the surface h, distance from the critical point (point of intersection of the jet axis with the surface) along the flow radius r. Data on the gas velocity decrease as the jet develops due to the loss of initial energy to engage the motionless surrounding gas in motion, is presented. The studies have shown that increase in the initial velocity of gas outflow brings the area of higher velocities closer to the surface both in the jet itself and in the fan jet. This factor contributes to heat transfer intensification. In addition, high speeds increase the total thickness of the fan flow and reduce the thickness of hydrodynamic boundary layer, which increases with distance from the critical point.

scholarly journals A Multi-GPU Parallel Algorithm in Hypersonic Flow Computations

2019 ◽  
Vol 2019 ◽  
pp. 1-15 ◽  
Author(s):  
Jianqi Lai ◽  
Hua Li ◽  
Zhengyu Tian ◽  
Ye Zhang
Keyword(s):  
Parallel Algorithm ◽  
Hypersonic Flow ◽  
Stokes Equations ◽  
Programming Model ◽  
Graphics Processing Unit ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Time Discretization ◽  
Processing Unit ◽  
Complex Flow

Computational fluid dynamics (CFD) plays an important role in the optimal design of aircraft and the analysis of complex flow mechanisms in the aerospace domain. The graphics processing unit (GPU) has a strong floating-point operation capability and a high memory bandwidth in data parallelism, which brings great opportunities for CFD. A cell-centred finite volume method is applied to solve three-dimensional compressible Navier–Stokes equations on structured meshes with an upwind AUSM+UP numerical scheme for space discretization, and four-stage Runge–Kutta method is used for time discretization. Compute unified device architecture (CUDA) is used as a parallel computing platform and programming model for GPUs, which reduces the complexity of programming. The main purpose of this paper is to design an extremely efficient multi-GPU parallel algorithm based on MPI+CUDA to study the hypersonic flow characteristics. Solutions of hypersonic flow over an aerospace plane model are provided at different Mach numbers. The agreement between numerical computations and experimental measurements is favourable. Acceleration performance of the parallel platform is studied with single GPU, two GPUs, and four GPUs. For single GPU implementation, the speedup reaches 63 for the coarser mesh and 78 for the finest mesh. GPUs are better suited for compute-intensive tasks than traditional CPUs. For multi-GPU parallelization, the speedup of four GPUs reaches 77 for the coarser mesh and 147 for the finest mesh; this is far greater than the acceleration achieved by single GPU and two GPUs. It is prospective to apply the multi-GPU parallel algorithm to hypersonic flow computations.

scholarly journals Linear pulse structure and signalling in a film flow on an inclined plane

1999 ◽  
Vol 396 ◽  
pp. 37-71 ◽  
Author(s):  
LEONID BREVDO ◽  
PATRICE LAURE ◽  
FREDERIC DIAS ◽  
THOMAS J. BRIDGES
Keyword(s):  
Free Surface ◽  
Saddle Point ◽  
Convective Instability ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Numerical Results ◽  
Navier Stokes ◽  
Surface Boundary ◽  
Navier Stokes Equations ◽  
Surface Boundary Conditions

The film flow down an inclined plane has several features that make it an interesting prototype for studying transition in a shear flow: the basic parallel state is an exact explicit solution of the Navier–Stokes equations; the experimentally observed transition of this flow shows many properties in common with boundary-layer transition; and it has a free surface, leading to more than one class of modes. In this paper, unstable wavepackets – associated with the full Navier–Stokes equations with viscous free-surface boundary conditions – are analysed by using the formalism of absolute and convective instabilities based on the exact Briggs collision criterion for multiple k-roots of D(k, ω) = 0; where k is a wavenumber, ω is a frequency and D(k, ω) is the dispersion relation function.The main results of this paper are threefold. First, we work with the full Navier–Stokes equations with viscous free-surface boundary conditions, rather than a model partial differential equation, and, guided by experiments, explore a large region of the parameter space to see if absolute instability – as predicted by some model equations – is possible. Secondly, our numerical results find only convective instability, in complete agreement with experiments. Thirdly, we find a curious saddle-point bifurcation which affects dramatically the interpretation of the convective instability. This is the first finding of this type of bifurcation in a fluids problem and it may have implications for the analysis of wavepackets in other flows, in particular for three-dimensional instabilities. The numerical results of the wavepacket analysis compare well with the available experimental data, confirming the importance of convective instability for this problem.The numerical results on the position of a dominant saddle point obtained by using the exact collision criterion are also compared to the results based on a steepest-descent method coupled with a continuation procedure for tracking convective instability that until now was considered as reliable. While for two-dimensional instabilities a numerical implementation of the collision criterion is readily available, the only existing numerical procedure for studying three-dimensional wavepackets is based on the tracking technique. For the present flow, the comparison shows a failure of the tracking treatment to recover a subinterval of the interval of unstable ray velocities V whose length constitutes 29% of the length of the entire unstable interval of V. The failure occurs due to a bifurcation of the saddle point, where V is a bifurcation parameter. We argue that this bifurcation of unstable ray velocities should be observable in experiments because of the abrupt increase by a factor of about 5.3 of the wavelength across the wavepacket associated with the appearance of the bifurcating branch. Further implications for experiments including the effect on spatial amplification rate are also discussed.

Numerical Investigation of Positive Displacement Rotary Lobe Pump With Twisted Rotors

2014 ◽  
Author(s):  
Xiaojun Jiang ◽  
Yi Li ◽  
Zhaohui He ◽  
Cui Baoling ◽  
Wenlong Dong
Keyword(s):  
Flow Structure ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Internal Flow ◽  
Dynamic Flow ◽  
Flow Fluctuation ◽  
Flow Field Characteristics ◽  
Lobe Pump ◽  
The Impact

The three-dimensional flow field characteristics are obtained by performing numerical simulation of flow in a lobe pump with twisted rotors. The relationship between the dynamic flow structure and the flow fluctuation is explored. Actually, the viscous incompressible Navier-Stokes equations are solved within an unsteady flow model. The dynamic mesh technique is applied to obtain the dynamic flow structure. By comparing the simulated results of straight rotor with those of twisted rotor, the effect of rotor shape on the flow fluctuation was revealed. Finally, the impact of the lobes number of rotors on flow pulsations is discussed. The results show that there is an intrinsic relationship between the flow fluctuation and the vortex in the lobe pump. The use of twisted rotors can effectively improve the internal flow characteristics of lobe pump and reduce flow fluctuation. With the increase of the number of lobes, the lobe pump output is more stable and capacity has been improved.

Sign in / Sign up

Export Citation Format

Share Document