scholarly journals Gas Turbine Inlet Air Cooling and the Effect on a Westinghouse 501D5 CT

1995 ◽  
Author(s):  
Chuck Kohlenberger
Keyword(s):  
Gas Turbine ◽  
Mass Flow ◽  
Heat Rate ◽  
International Standards ◽  
Air Cooling ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Turbine Inlet ◽  
Air Temperatures ◽  
Exhaust Gas Temperature

The temperature of the air entering a gas turbine prime mover has a dramatic effect on its performance, including output, heat rate, and exhaust gas temperature (EGT). These variations are easily observed in actual operation and by reference to generic gas turbine (GT) performance curves. The gross capacity increase of a GT operating at 40F (8C) inlet compared to operation at 102F (70C) is 28%. The gross reduction in heat rate for this 62F (16.7C) differential is 6%, and the exhaust gas temperature is reduced 5%. Since the overall mass flow through the GT is increased through the cooling process, the added energy available in the heat recovery steam generator (HRSG), is increased 8% The significant improvements in GT output and efficiency which can be achieved by maintaining lower inlet air temperatures encourage the manufacturer, systems engineer, owner, and operator of GT facilities to consider seriously the implementation of a gas turbine inlet air cooling (GTIAC) system. GTIAC systems have proven to produce some very excellent economic paybacks due to increased power output, EG mass flow, and reduced heat rates. Generic gross performance factors are plotted (See Figure 1) against inlet air temperature compared to International Standards Organization (ISO) conditions.

scholarly journals Early Fault Detection of Gas Turbine Hot Components Based on Exhaust Gas Temperature Profile Continuous Distribution Estimation

Energies ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5950
Author(s):  
Jinfu Liu ◽  
Mingliang Bai ◽  
Zhenhua Long ◽  
Jiao Liu ◽  
Yujia Ma ◽  
...  
Keyword(s):  
Fault Detection ◽  
Temperature Profile ◽  
Gas Turbine ◽  
Detection Method ◽  
Continuous Distribution ◽  
Detection Sensitivity ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Early Fault Detection ◽  
Exhaust Gas Temperature

Failures of the gas turbine hot components often cause catastrophic consequences. Early fault detection can detect the sign of fault occurrence at an early stage, improve availability and prevent serious incidents of the plant. Monitoring the variation of exhaust gas temperature (EGT) is an effective early fault detection method. Thus, a new gas turbine hot components early fault detection method is developed in this paper. By introducing a priori knowledge and quantum particle swarm optimization (QPSO), the exhaust gas temperature profile continuous distribution model is established with finite EGT measuring data. The method eliminates influences of operating and ambient condition changes and especially the gas swirl effect. The experiment reveals the presented method has higher fault detection sensitivity.

scholarly journals A Fault Diagnosis Approach for Gas Turbine Exhaust Gas Temperature Based on Fuzzy C-Means Clustering and Support Vector Machine

2015 ◽  
Vol 2015 ◽  
pp. 1-11 ◽  
Author(s):  
Zhi-tao Wang ◽  
Ning-bo Zhao ◽  
Wei-ying Wang ◽  
Rui Tang ◽  
Shu-ying Li
Keyword(s):  
Fault Diagnosis ◽  
Gas Turbine ◽  
Clustering Algorithm ◽  
Support Vector ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Fcm Clustering ◽  
Gas Turbine Exhaust ◽  
Exhaust Gas Temperature ◽  
Turbine Exhaust

As an important gas path performance parameter of gas turbine, exhaust gas temperature (EGT) can represent the thermal health condition of gas turbine. In order to monitor and diagnose the EGT effectively, a fusion approach based on fuzzy C-means (FCM) clustering algorithm and support vector machine (SVM) classification model is proposed in this paper. Considering the distribution characteristics of gas turbine EGT, FCM clustering algorithm is used to realize clustering analysis and obtain the state pattern, on the basis of which the preclassification of EGT is completed. Then, SVM multiclassification model is designed to carry out the state pattern recognition and fault diagnosis. As an example, the historical monitoring data of EGT from an industrial gas turbine is analyzed and used to verify the performance of the fusion fault diagnosis approach presented in this paper. The results show that this approach can make full use of the unsupervised feature extraction ability of FCM clustering algorithm and the sample classification generalization properties of SVM multiclassification model, which offers an effective way to realize the online condition recognition and fault diagnosis of gas turbine EGT.

Performance Characteristics of a Diesel Engine Fueled With Avio-Kerosene

2003 ◽  
Author(s):  
Giancarlo Chiatti ◽  
Ornella Chiavola
Keyword(s):  
Diesel Engine ◽  
Combustion Chamber ◽  
Gas Turbine ◽  
Power Output ◽  
Pressure Rise ◽  
Experimental Tests ◽  
Diesel Oil ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Exhaust Gas Temperature

A comparative series of experimental tests has been performed on a 4-stroke multi cylinder indirect injection diesel engine fueled with diesel oil, pure gas-turbine fuel and gas-turbine fuel with additives. The engine has been equipped aimed at monitoring both the overall performances and the variation with time of the pressure in the pre-combustion chamber. Some key parameters have been investigated at different engine speeds and loads (ignition delay, pressure rise in the pre-combustion chamber, power output, specific fuel consumption, exhaust gas temperature) and discussed results are presented.

scholarly journals The Experimental and Simulation Study of Selective Catalytic Reduction System in a Single Cylinder Diesel Engine Using NH3as a Reducing Agent

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Manoj Kumar Athrashalil Phaily ◽  
Sreekumar Jayachandra Sreekala ◽  
Padmanabha Mohanan
Keyword(s):  
Diesel Engine ◽  
Selective Catalytic Reduction ◽  
Mass Flow ◽  
Catalytic Reduction ◽  
Pt Catalyst ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Single Cylinder ◽  
Induction Rate ◽  
Exhaust Gas Temperature

Selective catalytic reduction (SCR) technology has been widely used in automotive applications in order to meet the stringent limits on emission standards. The maximum NOxconversion efficiency of an SCR depends on temperature and mass flow rate of an exhaust gas. In order to assess the suitability of Cordierite/Pt catalyst for low temperature application, an experimental work is carried out using single cylinder diesel engine for different load conditions by varying ammonia induction rate from 0.2 kg/hr to 0.8 kg/hr. The simulation is carried out using AVL FIRE for the validation of experimental results. From the study, it has been found that for 0.6 kg/hr ammonia induction rate the maximum conversion is achieved, whereas, for 0.8 kg/hr, conversion is reduced due to desorption of ammonia. Also it has been found that, at 75% of load, for all mass flow rates of ammonia the conversion was drastically reduced due to higher exhaust gas temperature and higher emission of unburnt hydrocarbons. More than 55% of NOxconversion was achieved using Cordierite/Pt catalyst at a temperature of 320°C.

Experimental Investigation on the Effects of Swirlers Configurations and Air Inlet Partitioning in a Partially Premixed Double High Swirl Gas Turbine Model Combustor

2020 ◽  
Vol 143 (1) ◽  
Author(s):  
Amir Mardani ◽  
Benyamin Asadi Rekabdarkolaei ◽  
Hamed Rezapour Rastaaghi
Keyword(s):  
Gas Turbine ◽  
Combustion Efficiency ◽  
Exhaust Gas ◽  
Liquefied Petroleum Gas ◽  
Gas Temperature ◽  
Air Inlet ◽  
Flow Channeling ◽  
German Aerospace ◽  
Exhaust Gas Temperature ◽  
Turbine Model

Abstract In this work, a double-high swirl gas turbine model combustor (GTMC) has been experimentally investigated to identify the effects of air partitioning and swirlers geometry on combustion characteristics in terms of flame stability, exhaust gas temperature, NOx generation, and combustion efficiency. This high swirl model combustor is originally developed in the German Aerospace Center (DLR) and known as GTMC and recently reconstructed at Sharif University's Combustion Laboratory (named as SGTMC). Here, SGTMC run for liquefied petroleum gas (LPG) fuel and air oxidizer at room temperature and atmospheric pressure. Eleven different burner geometries, M1–M11, are considered for the aims of this work. Furthermore, the effects of burner confinement are also investigated. The results show that under the confined state, the flame has a lower width and height than the unconfined one. Exchanging the swirlers of annular and central air inlets shows a more stable and lifted V type flame with almost zero levels of CO and CH4. In addition, measurement showed that the annular swirler removing leads to incomplete combustion. Moreover, an increment in discharged air velocity leads to more completed combustion and less pollutant exhaust gas but the attachment of flame to the burner hub. Strengthening the flow channeling is not reasonable in terms of emission aspects. Moreover, burner configuring to counterrotating swirlers leads to a more stable flame but with lower combustion efficiency. Among 11 test cases, the original configuration and the case of exchanging the swirlers of annular and central air inlets are the best choices in terms of combustion efficiency and stability. Measurements show the improvement of burner stability, 2–10%, due to inlet air preheating.

Gas-Turbine-Cycle District Heating/Cooling-Power System With Refrigerating Exhaust

2010 ◽  
Author(s):  
Branko Stankovic
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Heat Input ◽  
District Heating ◽  
Heat Output ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Ghg Emission ◽  
Exhaust Gas Temperature ◽  
Gas Turbine Cycle

A gas-turbine-cycle modification has been proposed, optimized primarily for (district) heating purposes, with a side-effect of obtaining gas-turbine exhaust gas at very low temperatures and potentially GHG-emission-free. Since its primary purpose is district heating without power generation, the associated gas-turbine-cycle equipment (compressors, turbines, heat exchangers) is typically arranged so that a maximum possible ratio of heat output and heat input is achieved. Whenever the heat ratio is greater than unity, that is, greater than 100% of the heat input, the exhaust gas temperature at the last gas-turbine exit is lower than atmospheric temperature. In other words, this means that it is possible to achieve greater heat output (or GT-cycle “waste heat”) than the heat input, at the “expense” of the cold GT exhaust gas (its internal energy). It is possible to arrange proposed GT-cycle modification in various configurations, such as: simple GT cycle, recuperated, intercooled, intercooled-recuperated, reheat-recuperated and intercooled-reheat-recuperated GT cycle. Maximum achievable ratio of heat output and heat input is estimated to about 1.15 (115%) and corresponding minimum GT exhaust gas temperature can be lower than the CO2 solidification temperature at atmospheric pressure (−78°C or 195 K or −108.4°F). This also means that the GT exhaust-gas stream could be entirely GHG-emission-free, without GHG-s like H2O and/or CO2, which could therefore be captured and sequestered in solid state, and in addition at very low refrigerating temperature. Such low-temperature GT exhaust gas could then be used for refrigeration purposes, or ultimately to refrigerate the Earth’s atmosphere and thus mitigate global-warming effects. The proposed GT-cycle heating system can operate also in the combined heating/cooling and power (CCHP) mode or in the stand-alone power generation mode using a combined-cycle configuration. In such operating modes/regimes, the heating part of the CHP system could still maintain its inherent advantages (achievement of the ratio of heat output and heat input greater than unity, potentially GHG-emission-free GT exhaust gas at refrigerating temperature levels), with CC thermal efficiencies only slightly lower than today’s typical values and with the CHP performance similar or better than modern GTCC or steam-turbine based CHP cycles.

Three- and Seven-Point Optimally Weighted Recursive Median Filters for Gas Turbine Diagnostics

2011 ◽  
Vol 133 (10) ◽  
Author(s):  
V. N. Guruprakash ◽  
Ranjan Ganguli
Keyword(s):  
Gas Turbine ◽  
Fault Detection And Isolation ◽  
Exhaust Gas ◽  
Window Length ◽  
Rotor Speed ◽  
Gas Temperature ◽  
Median Filters ◽  
Optimal Filters ◽  
Fuel Flow ◽  
Exhaust Gas Temperature

Measured health signals incorporate significant details about any malfunction in a gas turbine. The attenuation of noise and removal of outliers from these health signals while preserving important features is an important problem in gas turbine diagnostics. The measured health signals are a time series of sensor measurements such as the low rotor speed, high rotor speed, fuel flow, and exhaust gas temperature in a gas turbine. In this article, a comparative study is done by varying the window length of acausal and unsymmetrical weighted recursive median filters and numerical results for error minimization are obtained. It is found that optimal filters exist, which can be used for engines where data are available slowly (three-point filter) and rapidly (seven-point filter). These smoothing filters are proposed as preprocessors of measurement delta signals before subjecting them to fault detection and isolation algorithms.

scholarly journals Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines: Part II Unsteady processes

2011 ◽  
Vol 18 (3) ◽  
pp. 37-42 ◽  
Author(s):  
Zbigniew Korczewski
Keyword(s):  
Gas Turbine ◽  
Temperature Measurements ◽  
Turbine Engines ◽  
Flow Section ◽  
Exhaust Gas ◽  
Gas Turbine Engines ◽  
Gas Temperature ◽  
Rate Of Increase ◽  
Exhaust Gas Temperature ◽  
Unsteady Processes

Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines: Part II Unsteady processes The second part of the article presents the results of operating diagnostic tests of a two- and three-shaft engine with a separate power turbine during the start-up and acceleration of the rotor units. Attention was paid to key importance of the correctness of operation of the automatic engine load control system, the input for which, among other signals, is the rate of increase of the exhaust gas flow temperature. The article presents sample damages of the engine flow section which resulted from disturbed functioning of this system. The unsteady operation of the compressor during engine acceleration was the source of excessive increase of the exhaust gas temperature behind the combustion chamber and partial burning of the turbine blade tips.

Sign in / Sign up

Export Citation Format

Share Document