Impact of Tip Clearance Size and Rotation Speed on the Surge Onset in a High Pressure Centrifugal Compressor

2012 ◽  
Author(s):  
Nicolas Buffaz ◽  
Isabelle Trébinjac
Keyword(s):  
Centrifugal Compressor ◽  
Rotation Speed ◽  
Pressure Sensors ◽  
Leading Edge ◽  
Suction Side ◽  
Boundary Layer Separation ◽  
Tip Clearance ◽  
Vaned Diffuser ◽  
The Impact ◽  
Blade Leading Edge

The results presented in the paper aim at investigating the impact of tip clearance size and rotation speed on the surge onset in a transonic single-stage centrifugal compressor composed of a backswept splittered unshrouded impeller and a vaned diffuser. For that purpose, various slow throttle ramps into surge were conducted from 100% to 60% design speed of the compressor and two different tip clearance heights were investigated. The 1MW LMFA-ECL test rig was used to carry out the tests in the compressor stage. Unsteady pressure measurements up to 150 KHz were carried out in the inducer (i.e. the entry zone of the impeller between the main blade leading edge and the splitter blade leading edge) and in the diffuser thanks to nine and fifteen static pressure sensors respectively. At cruise rotation speed (92.7% of the nominal rotation speed), the surge is triggered by a boundary layer separation on the diffuser vane suction side whatever the tip clearance height may be. No precursor of surge or pre-surge activity has been recorded in the diffuser or in the impeller. The surge reveals a spike-type inception and the tip clearance increase does not change the path into instability. At lower rotation speeds high frequency disturbances (nearly half the BPF) have been recorded in the inducer before surge. These disturbances can be understood as “tip clearance rotating disturbances” because they are generated at the leading edge of the main blades and move along the tip clearance trajectory. These disturbances reveal a very unstable behavior while the compressor runs into a stable operating point even if the flow at the tip of impeller is dramatically affected by these disturbances. But these disturbances do not trigger the surge which always originates in the diffuser.

scholarly journals Numerical Simulation of Stall Inception Mechanisms in a Centrifugal Compressor With Vaned Diffuser

2016 ◽  
Vol 138 (12) ◽  
Author(s):  
Y. Bousquet ◽  
N. Binder ◽  
G. Dufour ◽  
X. Carbonneau ◽  
M. Roumeas ◽  
...  
Keyword(s):  
Mass Flow ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Suction Side ◽  
Boundary Layer Separation ◽  
Flow Topology ◽  
Vaned Diffuser ◽  
Stall Inception ◽  
Flow Reduction

The present paper numerically investigates the stall inception mechanisms in a centrifugal compressor stage composed of a splittered unshrouded impeller and a vaned diffuser. Unsteady numerical simulations have been conducted on a calculation domain comprising all the blade passages over 360 deg for the impeller and the diffuser. Three stable operating points are simulated along a speed line, and the full path to instability is investigated. The paper focusses first on the effects of the mass flow reduction on the flow topology at the inlet of both components. Then, a detailed analysis of stall inception mechanisms is proposed. It is shown that at the inlet of both components, the mass flow reduction induces boundary layer separation on the blade suction side, which results in a vortex tube having its upper end at the casing and its lower end at the blade wall. Some similarities with flows in axial compressor operating at stall condition are outlined. The stall inception process starts with the growth of the amplitude of a modal wave rotating in the vaneless space. As the flow in the compressor is subsonic, the wave propagates upstream and interacts with the impeller flow structure. This interaction leads to the drop in the impeller pressure ratio.

Impact of Main and Splitter Blade Leading Edge Contour on the Performance of High Pressure Ratio Centrifugal Compressors

2014 ◽  
Author(s):  
Rodrigo R. Erdmenger ◽  
Vittorio Michelassi
Keyword(s):  
High Pressure ◽  
Pressure Ratio ◽  
Leading Edge ◽  
Tip Clearance ◽  
Flow Coefficient ◽  
Centrifugal Compressors ◽  
Operating Range ◽  
High Pressure Ratio ◽  
The Impact ◽  
Blade Leading Edge

The impact of leading edge sweep in an attempt to reduce shock losses and extend the stall margin on axial compressors has been extensively studied, however only a few studies have looked at understanding the impact of leading edge contouring on the performance of centrifugal compressors. The present work studies the impact of forward and aft sweep on the main and splitter blade leading edge of a generic high flow coefficient and high pressure ratio centrifugal compressor design and the impact on its overall peak efficiency, pressure ratio and operating range. The usage of aft sweep on the main blade led to an increase of the pressure ratio and efficiency, however it also led to a reduction of the stable operating range of the impeller analyzed. The forward sweep cases analyzed where the tip leading edge was displaced axially forward showed a slight increase in pressure ratio, and a significant increase on operating range. The impact of leading edge sweep on the sensitivity of the impeller performance to tip clearance was also studied. The impeller efficiency was found to be less sensitive to an increase of tip clearance for both aft and forward sweep cases studied. The forward sweep cases studied also showed a reduced sensitivity from operating range to tip clearance. The studies conducted on the splitter leading edge profile indicate that aft sweep may help to increase the operating range of the impeller analyzed by up to 16% while maintaining similar pressure ratio and efficiency characteristics of the impeller. The improvement of operating range obtained with the leading edge forward sweep and splitter aft sweep was caused by a reduction of the interaction of the tip vortex of the main blade with the splitter tip, and a reduction of the blockage caused by this interaction.

Spike and Modal Stall Inception in an Advanced Turbocharger Centrifugal Compressor

2009 ◽  
Vol 131 (3) ◽  
Author(s):  
Z. S. Spakovszky ◽  
C. H. Roduner
Keyword(s):  
Centrifugal Compressor ◽  
High Speed ◽  
Pressure Ratio ◽  
Pressure Sensors ◽  
Rotating Stall ◽  
Vaned Diffuser ◽  
Stall Inception ◽  
Compression System ◽  
The Impact ◽  
Highly Loaded

In turbocharger applications, bleed air near the impeller exit is often used for secondary flow systems to seal bearing compartments and to balance the thrust load on the bearings. There is experimental evidence that the performance and operability of highly-loaded centrifugal compressor designs can be sensitive to the amount of bleed air. To investigate the underlying mechanisms and to assess the impact of bleed air on the compressor dynamic behavior, a research program was carried out on a preproduction, 5.0 pressure ratio, high-speed centrifugal compressor stage of advanced design. The investigations showed that bleed air can significantly reduce the stable flow range. Compressor rig experiments, using an array of unsteady pressure sensors and a bleed valve to simulate a typical turbocharger environment, suggest that the path into compression system instability is altered by the bleed flow. Without the bleed flow, the prestall behavior is dominated by short-wavelength disturbances, or so called “spikes,” in the vaneless space between the impeller and the vaned diffuser. Introducing bleed flow at the impeller exit reduces endwall blockage in the vaneless space and destabilizes the highly-loaded vaned diffuser. The impact is a 50% reduction in stable operating range. The altered diffuser characteristic reduces the compression system damping responsible for long-wavelength modal prestall behavior. A four-lobed backward traveling rotating stall wave is experimentally measured in agreement with calculations obtained from a previously developed dynamic compressor model. In addition, a self-contained endwall blockage control strategy was employed, successfully recovering 75% of the loss in surge-margin due to the bleed flow and yielding a one point increase in adiabatic compressor efficiency.

Evolution Process of Diffuser Stall in a Centrifugal Compressor With Vaned Diffuser

2018 ◽  
Author(s):  
Nobumichi Fujisawa ◽  
Tetsuya Inui ◽  
Yutaka Ohta
Keyword(s):  
Centrifugal Compressor ◽  
Leading Edge ◽  
Boundary Layer Separation ◽  
Rotating Stall ◽  
Evolution Process ◽  
Cfd Analysis ◽  
Pressure Measurements ◽  
Velocity Measurements ◽  
Vaned Diffuser ◽  
Computational Fluid Dynamics Cfd

The evolution process of a diffuser rotating stall in a centrifugal compressor with a vaned diffuser was investigated by experimental and numerical analyses. From velocity measurements, it was found that the diffuser stall propagated near the shroud side in the vaneless space. As the mass flow decreased, a stage stall rotated within both the impeller and diffuser passages, instead of a diffuser stall. The evolution process of the diffuser stall had three stall forms. First, the diffuser stall, which was rotating on the shroud side, shifted to the hub side. Then, the diffuser stall moved into the impeller passages and evolved to a stage stall. From computational fluid dynamics (CFD) analysis, a tornado-type vortex was generated first, near the hub side of the diffuser leading edge, when the diffuser stall was shifted to the hub side. Next, a throat area blockage was formed near the hub side because of the boundary layer separation in the vaneless space. Finally, the blockage within the diffuser passages expanded to the impeller passages and developed into a stage stall. From the pressure measurements along the impeller and diffuser passages, the magnitude of pressure fluctuation on the casing wall of the diffuser throat area also suddenly increased when the diffuser stall shifted to the hub side. Therefore, the evolution area of the diffuser stall was caused by the evolution of the blockage near the throat area of the diffuser passage.

Experimental and Numerical Investigation of the Unsteady Flow Field in a Vaned Diffuser of a High-Speed Centrifugal Compressor

2015 ◽  
Vol 137 (7) ◽  
Author(s):  
Klemens Vogel ◽  
Reza S. Abhari ◽  
Armin Zemp
Keyword(s):  
Centrifugal Compressor ◽  
High Speed ◽  
Pressure Fluctuations ◽  
Leading Edge ◽  
Fast Response ◽  
Operating Conditions ◽  
Wake Flow ◽  
Vaned Diffuser ◽  
Wide Range ◽  
The Impact

Vaned diffusers in centrifugal compressor stages are used to achieve higher stage pressure ratios, higher stage efficiencies, and more compact designs. The interaction of the stationary diffuser with the impeller can lead to resonant vibration with potentially devastating effects. This paper presents unsteady diffuser vane surface pressure measurements using in-house developed, flush mounted, fast response piezoresistive pressure transducers. The unsteady pressures were recorded for nine operating conditions, covering a wide range of the compressor map. Experimental work was complemented by 3D unsteady computational fluid dynamics (CFD) simulations using ansys cfx V12.1 to detail the unsteady diffuser aerodynamics. Pressure fluctuations of up to 34.4% of the inlet pressure were found. High pressure variations are present all along the vane and are not restricted to the leading edge region. Frequency analysis of the measured vane surface pressures show that reduced impeller loading, and the corresponding reduction of tip leakage fluid changes the characteristics of the fluctuations from a main blade count to a total blade count. The unsteady pressure fluctuations in the diffuser originate from three distinct locations. The impact of the jet-wake flow leaving the impeller results in high variation close to the leading edge. It was observed that CFD results overpredicted the amplitude of the pressure fluctuation on average by 62%.

Evolution Process of Diffuser Stall in a Centrifugal Compressor With Vaned Diffuser

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
Nobumichi Fujisawa ◽  
Tetsuya Inui ◽  
Yutaka Ohta
Keyword(s):  
Fluid Dynamics ◽  
Boundary Layer ◽  
Centrifugal Compressor ◽  
Leading Edge ◽  
Boundary Layer Separation ◽  
Evolution Process ◽  
Cfd Analysis ◽  
Pressure Measurements ◽  
Vaned Diffuser ◽  
Computational Fluid Dynamics Cfd

This paper describes in detailed flow field in a centrifugal compressor with a vaned diffuser at off design point. Especially, we conducted both the experimental and numerical analysis in order to investigate the evolution process of a diffuser stall. At the stall point, the diffuser stall was initiated and rotated near the shroud side in the vaneless space. Furthermore, the diffuser stall was developed to a stage stall cell, as the mass flow was decreased. The developed stall cell was rotated within both the impeller and diffuser passages. The evolution process of the diffuser stall had three stall forms. First, the diffuser stall was rotating near the shroud side. Then, the diffuser stall shifted to the hub side and moved into the impeller passages. Finally, a stage stall was generated. From computational fluid dynamics (CFD) analysis, a tornado-type vortex was generated first, near the hub side of the diffuser leading edge, when the diffuser stall was shifted to the hub side. Next, a throat area blockage was formed near the hub side because of the boundary layer separation in the vaneless space. Finally, the blockage within the diffuser passages expanded to the impeller passages and developed into a stage stall. From the pressure measurements along the impeller and diffuser passages, the magnitude of pressure fluctuation on the casing wall of the diffuser throat area also suddenly increased when the diffuser stall shifted to the hub side. Therefore, the evolution area of the diffuser stall was caused by the evolution of the blockage near the throat area of the diffuser passage.

Spike and Modal Stall Inception in an Advanced Turbocharger Centrifugal Compressor

2007 ◽  
Author(s):  
Z. S. Spakovszky ◽  
C. H. Roduner
Keyword(s):  
Centrifugal Compressor ◽  
High Speed ◽  
Pressure Ratio ◽  
Pressure Sensors ◽  
Rotating Stall ◽  
Vaned Diffuser ◽  
Stall Inception ◽  
Compression System ◽  
The Impact ◽  
Highly Loaded

In turbocharger applications bleed air near the impeller exit is often used for secondary flow systems to seal bearing compartments and to balance the thrust load on the bearings. There is experimental evidence that the performance and operability of highly loaded centrifugal compressor designs can be sensitive to the amount of bleed air. To investigate the underlying mechanisms and to assess the impact of bleed air on the compressor dynamic behavior, a research program was carried out on a pre-production, 5.0 pressure ratio, high-speed centrifugal compressor stage of advanced design. The investigations showed that bleed air can significantly reduce the stable flow range. Compressor rig experiments, using an array of unsteady pressure sensors and a bleed valve to simulate a typical turbocharger environment, suggest that the path into compression system instability is altered by the bleed flow. Without bleed flow, the pre-stall behavior is dominated by short wavelength disturbances, or so called ‘spikes’, in the vaneless space between the impeller and the vaned diffuser. Introducing bleed flow at impeller exit reduces endwall blockage in the vaneless space and destabilizes the highly-loaded vaned diffuser. The impact is a 50% reduction in stable operating range. The altered diffuser characteristic reduces the compression system damping responsible for long wavelength, modal pre-stall behavior. A four-lobed backward traveling rotating stall wave is experimentally measured, in agreement with calculations obtained from a previously developed dynamic compressor model. In addition, a self-contained, endwall blockage control strategy was employed, successfully recovering 75% of the loss in surge-margin due to bleed flow and yielding a 1 point increase in adiabiatic compressor efficiency.

Experimental and Numerical Investigation of the Unsteady Flow Field in a Vaned Diffuser of a High-Speed Centrifugal Compressor

2014 ◽  
Author(s):  
Klemens Vogel ◽  
Reza S. Abhari ◽  
Armin Zemp
Keyword(s):  
Centrifugal Compressor ◽  
High Speed ◽  
Pressure Fluctuations ◽  
Leading Edge ◽  
Fast Response ◽  
Operating Conditions ◽  
Wake Flow ◽  
Vaned Diffuser ◽  
Wide Range ◽  
The Impact

Vaned diffusers in centrifugal compressor stages are used to achieve higher stage pressure ratios, higher stage efficiencies and more compact designs. The interaction of the stationary diffuser with the impeller can lead to resonant vibration with potentially devastating effects. This paper presents unsteady diffuser vane surface pressure measurements using in-house developed, flush mounted, fast response piezo-resistive pressure transducers. The unsteady pressures were recorded for 9 operating conditions, covering a wide range of the compressor map. Experimental work was complemented by 3D unsteady CFD simulations using ANSYS CFX V12.1 to detail the unsteady diffuser aerodynamics. Pressure fluctuations of up to 34.4% of the inlet pressure were found. High pressure variations are present all along the vane and are not restricted to the leading edge region. Frequency analysis of the measured vane surface pressures show that reduced impeller loading and the corresponding reduction of tip leakage fluid changes the characteristics of the fluctuations from a main blade count to a total blade count. The unsteady pressure fluctuations in the diffuser originate from three distinct locations. The impact of the jet wake flow leaving the impeller results in high variation close to the leading edge. It was observed that CFD results overpredicted the amplitude of the pressure fluctuation on average by 62%.

Numerical Investigation of the Flow in a Radial Vaned Diffuser Without and With Aspiration

2012 ◽  
Author(s):  
A. Marsan ◽  
I. Trébinjac ◽  
S. Coste ◽  
G. Leroy
Keyword(s):  
Skin Friction ◽  
Leading Edge ◽  
Major Change ◽  
Suction Side ◽  
Tip Clearance ◽  
Operating Point ◽  
Vaned Diffuser ◽  
Leading Role ◽  
Stable Operating ◽  
Blade Tip

An analysis of the flow in a centrifugal compressor vaned diffuser from the nominal operating point of the compressor stage to a point near surge was conducted. Study of performance coefficients, and then of the skin-friction pattern, reveals the growth of a corner stall between the hub wall and the suction side of the vane when moving the operating point towards surge. Considering the location of the skin-friction pattern singular elements, a boundary layer suction technique has been developed and then numerically tested. The hub wall corner stall was controlled, and performances predicted near surge have been significantly modified, as well as the flow structures when reaching the limit of numerical stable operating range: the major change in the topology of the flow occurs now within the impeller, in the splitter leading edge region, and let think about a leading role of the main blade tip clearance vortex in the instabilities release. The surge massflow seems to have been significantly reduced.

Numerical Investigation of Diffuser Flow Field and Rotating Stall in a Centrifugal Compressor With Vaned Diffuser

2017 ◽  
Author(s):  
Yang Zhao ◽  
Jiayi Zhao ◽  
Zhiheng Wang ◽  
Guang Xi
Keyword(s):  
Centrifugal Compressor ◽  
Leading Edge ◽  
Suction Side ◽  
Rotating Stall ◽  
Tip Leakage Flow ◽  
Vaned Diffuser ◽  
Flow Angle ◽  
Diffuser Flow ◽  
Flow Phenomena ◽  
Reversal Flow

The diffuser rotating stall in a centrifugal compressor with vaned diffuser is one of important unsteady flow phenomena, which limits the operating range of the compressor. In this paper, the unsteady CFD analysis on a low-speed centrifugal compressor has been performed to investigate the flow characteristic in the diffuser and the propagation of the diffuser rotating stall. The flow behaviors at the outlet of the impeller at design and off-design conditions are firstly investigated. It is found that a reversal flow, induced by the tip leakage flow, exists near the shroud at the impeller outlet and becomes serious with the mass flow rate reduced. Due to the span-wise variation of the flow angle at the diffuser inlet and the inversed pressure gradient in the passage, the leading-edge vortex (LEV) generates on the diffuser leading edge. The LEV then induces the secondary flow in the diffuser passage and then causes the hub-corner separation. Furthermore, the propagation of the diffuser rotating stall is presented in details. The suction-side separation near the hub induces the blockage in the passage. And the shedding vortex from the suction side moves toward the leading edge of the adjacent blade. When the vortex reaches to the leading edge of the adjacent blade, the incidence increase and a new separation occurs on the suction side. With the development of the new separation, the passage becomes blocked gradually and the upstream stalled passage recovers to a normal condition. The rotating stall propagates along the direction of the impeller rotation at about 4.5% of the impeller rotational speed.

Sign in / Sign up

Export Citation Format

Share Document