Experimental Study of Cylindrical Latent Heat Energy Storage Systems Using Lauric Acid as the Phase Change Material

2012 ◽  
Author(s):  
Chang Liu ◽  
Robynne E. Murray ◽  
Dominic Groulx
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Energy Storage ◽  
Phase Change ◽  
Latent Heat ◽  
Storage Systems ◽  
Heat Energy ◽  
Hot Water ◽  
Energy Storage Systems ◽  
Water Flows

Phase change materials (PCMs) inside latent heat energy storage systems (LHESS) can be used to store large amounts of thermal energy in relatively small volumes. However, such systems are complicated to design from a heat transfer point of view since the low thermal conductivity of PCMs makes charging and discharging those systems challenging on a usable time scale. Results of experiments performed on both a vertical and a horizontal cylindrical LHESS, during charging, discharging and simultaneous charging/discharging, are presented in this paper. Both LHESS are made of acrylic plastic, the horizontal LHESS has one 1/2″ copper pipe passing through its center. The vertical LHESS has two 1/2″ copper pipes, one through which hot water flows, and the other through which cold water flows. Each of the pipes has four longitudinal fins to enhance the overall rate of heat transfer to and from the PCM, therefore reducing the time required for charging and discharging. The objective of this work is to determine the phase change behavior of the PCM during the operation of the LHESS, as well as the heat transfer processes within the LHESS. Natural convection was found to play a crucial role during charging (melting) and during simultaneous charging/discharging (in the vertical LHESS). However, during discharging, the effect of natural convection was reduced in both systems.

scholarly journals Optimum Placement of Heating Tubes in a Multi-Tube Latent Heat Thermal Energy Storage

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1232
Author(s):  
Mohammad Ghalambaz ◽  
Hayder I. Mohammed ◽  
Ali Naghizadeh ◽  
Mohammad S. Islam ◽  
Obai Younis ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Energy Storage ◽  
Taguchi Method ◽  
Phase Change ◽  
Latent Heat ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Storage Systems ◽  
Heat Transfer Fluid ◽  
Energy Storage Systems

Utilizing phase change materials in thermal energy storage systems is commonly considered as an alternative solution for the effective use of energy. This study presents numerical simulations of the charging process for a multitube latent heat thermal energy storage system. A thermal energy storage model, consisting of five tubes of heat transfer fluids, was investigated using Rubitherm phase change material (RT35) as the. The locations of the tubes were optimized by applying the Taguchi method. The thermal behavior of the unit was evaluated by considering the liquid fraction graphs, streamlines, and isotherm contours. The numerical model was first verified compared with existed experimental data from the literature. The outcomes revealed that based on the Taguchi method, the first row of the heat transfer fluid tubes should be located at the lowest possible area while the other tubes should be spread consistently in the enclosure. The charging rate changed by 76% when varying the locations of the tubes in the enclosure to the optimum point. The development of streamlines and free-convection flow circulation was found to impact the system design significantly. The Taguchi method could efficiently assign the optimum design of the system with few simulations. Accordingly, this approach gives the impression of the future design of energy storage systems.

scholarly journals Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3821
Author(s):  
Kassianne Tofani ◽  
Saeed Tiari
Keyword(s):  
Energy Storage ◽  
Phase Change ◽  
Latent Heat ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Phase Change Materials ◽  
Storage Systems ◽  
Heat Pipes ◽  
Energy Storage Systems ◽  
Thermal Energy Storage Systems

Latent heat thermal energy storage systems (LHTES) are useful for solar energy storage and many other applications, but there is an issue with phase change materials (PCMs) having low thermal conductivity. This can be enhanced with fins, metal foam, heat pipes, multiple PCMs, and nanoparticles (NPs). This paper reviews nano-enhanced PCM (NePCM) alone and with additional enhancements. Low, middle, and high temperature PCM are classified, and the achievements and limitations of works are assessed. The review is categorized based upon enhancements: solely NPs, NPs and fins, NPs and heat pipes, NPs with highly conductive porous materials, NPs and multiple PCMs, and nano-encapsulated PCMs. Both experimental and numerical methods are considered, focusing on how well NPs enhanced the system. Generally, NPs have been proven to enhance PCM, with some types more effective than others. Middle and high temperatures are lacking compared to low temperature, as well as combined enhancement studies. Al2O3, copper, and carbon are some of the most studied NP materials, and paraffin PCM is the most common by far. Some studies found NPs to be insignificant in comparison to other enhancements, but many others found them to be beneficial. This article also suggests future work for NePCM and LHTES systems.

Thermal Behavior of Phase Change Material During Charging Inside a Finned Cylindrical Latent Heat Energy Storage System: Effects of the Arrangement and Number of Fins

2010 ◽  
Author(s):  
Dominic Groulx ◽  
Wilson Ogoh
Keyword(s):  
Energy Storage ◽  
Phase Change ◽  
Phase Change Material ◽  
Latent Heat ◽  
Storage System ◽  
Heat Energy ◽  
Hot Water ◽  
Heat Of Fusion ◽  
Melting Front ◽  
Change Material

One way of storing thermal energy is through the use of latent heat energy storage systems. One such system, composed of a cylindrical container filled with paraffin wax, through which a copper pipe carrying hot water is inserted, is presented in this paper. It is shown that the physical processes encountered in the flow of water, the heat transfer by conduction and convection, and the phase change behavior of the phase change material can be modeled numerically using the finite element method. Only charging (melting) is treated in this paper. The appearance and the behavior of the melting front can be simulated by modifying the specific heat of the PCM to account for the increased amount of energy, in the form of latent heat of fusion, needed to melt the PCM over its melting temperature range. The effects of adding fins to the system are also studied, as well as the effects of the water inlet velocity.

Sign in / Sign up

Export Citation Format

Share Document