VIV Response and Drag Measurements of Circular Cylinders Fitted With Permeable Meshes

2015 ◽  
Author(s):  
Murilo M. Cicolin ◽  
Gustavo R. S. Assi
Keyword(s):  
Reynolds Number ◽  
Long Range ◽  
Flow Direction ◽  
Cross Flow ◽  
Circular Cylinders ◽  
Peak Response ◽  
Vortex Induced Vibrations ◽  
Different Types ◽  
Cylindrical Tubes ◽  
Low Mass

Experiments have been carried out on models of rigid circular cylinders fitted with three different types of permeable meshes to investigate their effectiveness in the suppression of vortex-induced vibrations (VIV). Measurements of amplitude of vibration and drag force are presented for models with low mass and damping which are free to respond in the cross-flow direction. Results for two meshes made of ropes and cylindrical tubes are compared with the VIV response of a bare cylinder and that of a known suppressor called the “ventilated trousers” (VT). All three meshes achieved an average 50% reduction of the peak response when compared with that of the bare cylinder. The sparse mesh configuration presented a similar behaviour to the VT, while the dense mesh produced considerable VIV response for an indefinitely long range of reduced velocity. All the three meshes have increased drag when compared with that of the bare cylinder. Reynolds number ranged from 5,000 to 25,000 and reduced velocity was varied between 2 and 15.

Suppression of the Vortex-Induced Vibration of a Circular Cylinder With Permeable Meshes

2014 ◽  
Author(s):  
Murilo M. Cicolin ◽  
Cesar M. Freire ◽  
Gustavo R. S. Assi
Keyword(s):  
Reynolds Number ◽  
Flow Direction ◽  
Vortex Formation ◽  
Cross Flow ◽  
Circular Cylinders ◽  
Vortex Induced Vibrations ◽  
Image Velocimetry ◽  
Different Types ◽  
Cylindrical Tubes ◽  
Low Mass

Experiments have been carried out on models of rigid circular cylinders fitted with three different types of permeable meshes to investigate their effectiveness in the suppression of vortex-induced vibrations (VIV). Measurements of the dynamic response are presented for models with low mass and damping which are free to respond in the cross-flow direction. Reynolds number ranged from 1,000 to 10,000 and reduced velocity was varied between 2 and 13. Also presented are measurements of the wake of static models with Particle Image Velocimetry (PIV) at Reynolds number equal to 4000. Results for two meshes made of ropes and cylindrical tubes are compared with the VIV response of a bare cylinder and that of a known suppressor called the “ventilated trousers” (VT). All three meshes achieved an average 50% reduction of the response when compared with that of the bare cylinder. The sparse mesh configuration presented a similar behaviour to the VT, while the dense mesh produced considerable VIV response for an indefinitely long range of reduced velocity. Visualisation of the flow by PIV around static cylinders revealed that all suppressors disrupt the vortex shedding and increase the formation length when compared to the bare cylinder. The VT mesh, which presented the best suppression, also presented the largest vortex formation length.

Response of a Circular Cylinder Fitted With Permeable Meshes Acting as VIV Suppressors

2014 ◽  
Author(s):  
Murilo M. Cicolin ◽  
Gustavo R. S. Assi
Keyword(s):  
Reynolds Number ◽  
Circular Cylinder ◽  
Dynamic Response ◽  
Flow Direction ◽  
Cross Flow ◽  
Circular Cylinders ◽  
Vortex Induced Vibrations ◽  
Different Types ◽  
Cylindrical Tubes ◽  
Low Mass

Experiments have been carried out on models of rigid circular cylinders fitted with three different types of permeable meshes to investigate their effectiveness in the suppression of vortex-induced vibrations (VIV). Measurements of the dynamic response are presented for models with low mass and damping which are free to respond in the cross-flow direction. Results for two meshes made of ropes and cylindrical tubes are compared with the VIV response of a bare cylinder and that of a known suppressor called the “ventilated trousers” (VT). All three meshes achieved an average 50% reduction of the response when compared with that of the bare cylinder. The sparse mesh configuration presented a similar behaviour to the VT, while the dense mesh produced considerable VIV response for an indefinitely long range of reduced velocity. Reynolds number ranged from 1,000 to 10,000 and reduced velocity was varied between 2 and 13.

Vortex-Induced Vibrations of a Cylinder at Subcritical Reynolds Number

2011 ◽  
Author(s):  
Yoann Jus ◽  
Elisabeth Longatte ◽  
Jean-Camille Chassaing ◽  
Pierre Sagaut
Keyword(s):  
Reynolds Number ◽  
Numerical Simulations ◽  
Numerical Study ◽  
Damping Ratio ◽  
Experimental Studies ◽  
Cross Flow ◽  
Physical Analysis ◽  
Arbitrary Lagrangian Eulerian ◽  
Vortex Induced Vibrations ◽  
Low Mass

The present work focusses on the numerical study of Vortex-Induced Vibrations (VIV) of an elastically mounted cylinder in a cross flow at moderate Reynolds numbers. Low mass-damping experimental studies show that the dynamic behavior of the cylinder exhibits a three-branch response model, depending on the range of the reduced velocity. However, few numerical simulations deal with accurate computations of the VIV amplitudes at the lock-in upper branch of the bifurcation diagram. In this work, the dynamic response of the cylinder is investigated by means of three-dimensional Large Eddy Simulation (LES). An Arbitrary Lagrangian Eulerian framework is employed to account for fluid solid interface boundary motion and grid deformation. Numerous numerical simulations are performed at a Reynolds number of 3900 for both no damping and low-mass damping ratio and various reduced velocities. A detailed physical analysis is conducted to show how the present methodology is able to capture the different VIV responses.

The Numerical Research of Two-Degrees-of-Freedom Vortex-Induced Vibrations of Circular Cylinders

2012 ◽  
Vol 204-208 ◽  
pp. 4598-4601
Author(s):  
Jie Li Fan ◽  
Wei Ping Huang
Keyword(s):  
Degrees Of Freedom ◽  
Amplitude Ratio ◽  
Flow Direction ◽  
Cross Flow ◽  
Circular Cylinders ◽  
Two Degrees Of Freedom ◽  
Line Frequency ◽  
Ansys Cfx ◽  
Vortex Induced Vibrations ◽  
Lock In

The two-degrees-of-freedom of vortex-induced vibration of circular cylinders is numerically simulated with the software ANSYS/CFX. The VIV characteristic, in the two different conditions (A/D=0.07 and A/D=1.0), is analyzed. When A/D is around 0.07, the amplitude ratio of the cylinder’s VIV between in-line and cross-flow direction in the lock-in is lower than that in the lock-out. The in-line frequency is twice of that in cross-flow direction in the lock-out, but in the lock-in, it is the same as that in cross-flow direction and the same as that of lift force. When A/D is around 1.0, the amplitude ratio of the VIV between in-line and cross-flow in the lock-in is obviously larger than that in the lock-out. Both in the lock-in and in the lock-out, the in-line frequency is twice of that in cross-flow direction.

The Effect of Rotational Friction on the Stability of Short-Tailed Fairings Suppressing Vortex-Induced Vibrations

2011 ◽  
Author(s):  
Gustavo R. S. Assi ◽  
Peter W. Bearman ◽  
Michael A. Tognarelli ◽  
Julia R. H. Rodrigues
Keyword(s):  
Circular Cylinder ◽  
Lift Force ◽  
Flow Direction ◽  
Fluid Dynamic ◽  
Cross Flow ◽  
Critical Limit ◽  
Vortex Induced Vibrations ◽  
Equivalent Length ◽  
Low Mass ◽  
The Stability

Experiments have been carried out on a free-to-rotate short-tail fairing fitted to a rigid length of circular cylinder to investigate the effect of rotational friction on the stability of this type of VIV suppressor. Measurements of the dynamic response are presented for models with low mass and damping which are free to respond in the cross-flow and streamwise directions. It is shown how VIV can be reduced if the fairing presents a rotational friction above a critical limit. In this configuration the fairing finds a stable position deflected from the flow direction and a steady lift force appears towards the side the fairing has deflected. The fluid-dynamic mechanism is very similar to that observed for a free-to-rotate splitter plate of equivalent length.

VIV Suppression and Drag Reduction With Pivoted Control Plates on a Circular Cylinder

2008 ◽  
Author(s):  
Gustavo R. S. Assi ◽  
Peter W. Bearman
Keyword(s):  
Reynolds Number ◽  
Circular Cylinder ◽  
Drag Reduction ◽  
Flow Direction ◽  
Cross Flow ◽  
Two Dimensional ◽  
Dimensional Control ◽  
Helical Strakes ◽  
Low Mass ◽  
Viv Suppression

Experiments have been carried out on two-dimensional devices fitted to a rigid length of circular cylinder to investigate the efficiency of pivoting control plates as VIV suppressors. Measurements are presented for a circular cylinder with low mass and damping which is free to respond in the cross-flow direction. It is shown how vortex-induced vibration can be practically eliminated by using free to rotate, two-dimensional control plates. Unlike helical strakes, the devices achieve VIV suppression with drag reduction. The device producing the largest drag reduction was found to have a drag coefficient equal to about 70% of that for a plain cylinder at the same Reynolds number.

Vortex-Induced Vibration of Two Side-by-Side Cylinders With a Small Gap in Uniform Flow

2017 ◽  
Author(s):  
Adnan Munir ◽  
Ming Zhao ◽  
Helen Wu
Keyword(s):  
Stokes Equations ◽  
Flow Direction ◽  
Three Dimensional ◽  
Cross Flow ◽  
Circular Cylinders ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Gap Ratio ◽  
Vortex Induced Vibrations ◽  
Lock In

Vortex-induced vibrations of two elastically mounted and rigidly coupled circular cylinders in side-by-side arrangement in steady flow are investigated numerically. The vibration of the cylinders is limited to the cross-flow direction only. The three-dimensional Navier-Stokes equations are solved using the Petrov-Galerkin Finite element method and the equation of motion is solved using the fourth order Runge Kutta method. It is well known that when the gap between two stationary side-by-side cylinders is very small, the flow between the two cylinders is biased towards one cylinder and the lift force on each cylinder is significantly smaller than that of an isolated single cylinder. The aim of this study is to investigate the effect of a small gap ratio of 0.5 between the two cylinders on the lock-in regime and the amplitude of the vibration of two side-by-side cylinders in a fluid flow. Simulations are carried out for a constant mass ratio of 2, a constant Reynolds number of 1000 and a range of reduced velocities. It is found that in the lock-in range of the reduced velocity, the two cylinders vibrate about their balance position with high amplitudes. Outside the lock-in regime the flow from the gap becomes biased towards one cylinder, which is similar to that from the gap between stationary cylinders.

Wake-Induced Vibration of a Pair of Circular Cylinders and Its Dependency on Reynolds Number

2010 ◽  
Author(s):  
Gustavo R. S. Assi ◽  
Peter W. Bearman ◽  
Julio R. Meneghini
Keyword(s):  
Reynolds Number ◽  
Flow Direction ◽  
Water Channel ◽  
Cross Flow ◽  
Circular Cylinders ◽  
Small Range ◽  
Rigid Cylinder ◽  
Velocity Parameter ◽  
Circulating Water ◽  
The Cross

This paper investigates the wake-induced vibration (WIV) of the downstream cylinder of a pair as far as its dependency of Reynolds number is concerned. Experiments have been conducted in a circulating water channel with a rigid cylinder elastically mounted to respond with oscillations in the cross-flow direction. Various sets of coil springs were employed to vary the reduced velocity of the system maintaining constant the Reynolds number. Experiments performed with a cylinder mounted without springs provided the idealised case of reduced velocity equal to infinity. We conclude that the amplitude of the WIV response has a strong dependency on Reynolds number even within the small range between Re = 2 × 103 and 2.5 × 104. If the reduced velocity parameter is isolated — by making it equal to infinity, for instance — the Re-dependency still dominates over the behaviour of the response.

scholarly journals Energy and Exergy Analyses of Tube Banks in Waste Heat Recovery Applications

Energies ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 2094 ◽  
Author(s):  
Mustafa Erguvan ◽  
David MacPhee
Keyword(s):  
Energy Efficiency ◽  
Reynolds Number ◽  
Heat Recovery ◽  
Waste Heat ◽  
Cross Flow ◽  
Exergy Efficiency ◽  
Circular Cylinders ◽  
Published Data ◽  
Energy And Exergy ◽  
Exergy Analyses

In this study, energy and exergy analyses have been investigated numerically for unsteady cross-flow over heated circular cylinders. Numerous simulations were conducted varying the number of inline tubes, inlet velocity, dimensionless pitch ratios and Reynolds number. Heat leakage into the domain is modeled as a source term. Numerical results compare favorably to published data in terms of Nusselt number and pressure drop. It was found that the energy efficiency varies between 72% and 98% for all cases, and viscous dissipation has a very low effect on the energy efficiency for low Reynolds number cases. The exergy efficiency ranges from 40–64%, and the entropy generation due to heat transfer was found to have a significant effect on exergy efficiency. The results suggest that exergy efficiency can be maximized by choosing specific pitch ratios for various Reynolds numbers. The results could be useful in designing more efficient heat recovery systems, especially for low temperature applications.

Strouhal Number for VIV Excitation of Long Slender Structures

2018 ◽  
Author(s):  
Andrew E. Potts ◽  
Douglas A. Potts ◽  
Hayden Marcollo ◽  
Kanishka Jayasinghe
Keyword(s):  
Reynolds Number ◽  
Strouhal Number ◽  
Degrees Of Freedom ◽  
Measurement Techniques ◽  
Cross Flow ◽  
Degree Of Freedom ◽  
Circular Cylinders ◽  
Two Degrees Of Freedom ◽  
Shedding Frequency ◽  
Eddy Shedding

The prediction of Vortex-Induced Vibration (VIV) of cylinders under fluid flow conditions depends upon the eddy shedding frequency, conventionally described by the Strouhal Number. The most commonly cited relationship between Strouhal Number and Reynolds Number for circular cylinders was developed by Lienhard [1], whereby the Strouhal Number exhibits a consistent narrow band of about 0.2 (conventional across the sub-critical Re range), with a pronounced hump peaking at about 0.5 within the critical flow regime. The source data underlying this relationship is re-examined, wherein it was found to be predominantly associated with eddy shedding frequency about fixed or stationary cylinders. The pronounced hump appears to be an artefact of the measurement techniques employed by various investigators to detect eddy-shedding frequency in the wake of the cylinder. A variety of contemporary test data for elastically mounted cylinders, with freedom to oscillate under one degree of freedom (i.e. cross flow) and two degrees of freedom (i.e. cross flow and in-line) were evaluated and compared against the conventional Strouhal Number relationship. It is well established for VIV that the eddy shedding frequency will synchronise with the near resonant motions of a dynamically oscillating cylinder, such that the resultant bandwidth of lock-in exhibits a wider range of effective Strouhal Numbers than that reflected in the narrow-banded relationship about a mean of 0.2. However, whilst cylinders oscillating under one degree of freedom exhibit a mean Strouhal Number of 0.2 consistent with fixed/stationary cylinders, cylinders with two degrees of freedom exhibit a much lower mean Strouhal Number of around 0.14–0.15. Data supports the relationship that Strouhal Number does slightly diminish with increasing Reynolds Number. For oscillating cylinders, the bandwidth about the mean Strouhal Number value appears to remain largely consistent. For many practical structures in the marine environment subject to VIV excitation, such as long span, slender risers, mooring lines, pipeline spans, towed array sonar strings, and alike, the long flexible cylinders will respond in two degrees of freedom, where the identified difference in Strouhal Number is a significant aspect to be accounted for in the modelling of its dynamic behaviour.

Sign in / Sign up

Export Citation Format

Share Document