scholarly journals Mechanical response and pore pressure generation in granular filters subjected to uniaxial cyclic loading

2018 ◽  
Vol 55 (12) ◽  
pp. 1756-1768
Author(s):  
Jahanzaib Israr ◽  
Buddhima Indraratna
Keyword(s):  
Cyclic Loading ◽  
Pore Pressure ◽  
Pore Water ◽  
Mechanical Response ◽  
Pore Water Pressure ◽  
Axial Strain ◽  
Water Pressure ◽  
Internal Erosion ◽  
Excess Pore Water Pressure ◽  
Excess Pore

This paper presents results from a series of piping tests carried out on a selected range of granular filters under static and cyclic loading conditions. The mechanical response of filters subjected to cyclic loading could be characterized in three distinct phases; namely, (I) pre-shakedown, (II) post-shakedown, and (III) post-critical (i.e., the occurrence of internal erosion). All the permanent geomechanical changes such, as erosion, permeability variations, and axial strain developments, took place during phases I and III, while the specimen response remained purely elastic during phase II. The post-critical occurrence of erosion incurred significant settlement that may not be tolerable for high-speed railway substructures. The analysis revealed that a cyclic load would induce excess pore-water pressure, which, in corroboration with steady seepage forces and agitation due to dynamic loading, could then cause internal erosion of fines from the specimens. The resulting excess pore pressure is a direct function of the axial strain due to cyclic densification, as well as the loading frequency and reduction in permeability. A model based on strain energy is proposed to quantify the excess pore-water pressure, and subsequently validated using current and existing test results from published studies.

scholarly journals Radial consolidation response upon the application and removal of vacuum and fill loading

2015 ◽  
Vol 52 (12) ◽  
pp. 2156-2162 ◽  
Author(s):  
Kourosh Kianfar ◽  
Buddhima Indraratna ◽  
Cholachat Rujikiatkamjorn ◽  
Serge Leroueil
Keyword(s):  
Pore Pressure ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Axial Strain ◽  
Water Pressure ◽  
Vacuum Pressure ◽  
Excess Pore Pressure ◽  
Excess Pore Water Pressure ◽  
Removal Time ◽  
Excess Pore

This Note presents a laboratory study using a Rowe cell to compare the consolidation responses upon vacuum pressure and fill load application and removal. The influences of the duration of application and removal of fill load and vacuum pressures on radial consolidation were investigated using excess pore-water pressure, axial strain, and overconsolidation ratio. It is shown that the appropriate removal time for vacuum pressure can be determined based on excess pore pressure responses.

scholarly journals Post-Cyclic Mechanical Behaviors of Undisturbed Soft Clay with Different Degrees of Reconsolidation

2021 ◽  
Vol 11 (16) ◽  
pp. 7612
Author(s):  
Yuan Lu ◽  
Jian Chen ◽  
Juehao Huang ◽  
Libo Feng ◽  
Song Yu ◽  
...  
Keyword(s):  
Shear Strength ◽  
Cyclic Loading ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soft Soil ◽  
Undrained Shear Strength ◽  
Excess Pore Water Pressure ◽  
Undrained Shear ◽  
Excess Pore

Soft soil is often subjected to cyclic loading such as that imposed during storms, under traffic, or in an earthquake. Furthermore, the cyclic-loading-induced excess pore water pressure can be partially dissipated after cyclic loading. Thus, different reconsolidation processes should be considered. A series of static and dynamic triaxial tests were conducted on undisturbed soft soil to determine the post-cyclic mechanical behavior thereof, such as the variation of undrained shear strength, the development of excess pore water pressure, and the evolution of effective stress path. The effects of consolidated confining pressure, cyclic stress ratio, and degree of reconsolidation were analyzed. Results show that the trend of all stress–strain curves is similar under different conditions. The effect of the degree of reconsolidation is such that, with increasing the degree of reconsolidation, the shear strength is enhanced. Meanwhile, compared with undrained shear strength without cyclic loading, the shear strength after cyclic loading with full reconsolidation is increased. These factors also have a significant effect on the undrained shear strength: the greater both the confining pressure and cyclic stress ratio are, the higher the undrained shear strength. A positive excess pore water pressure is always observed during post-cyclic shearing process, irrespective of different factors. The S-shaped effective stress paths under different test conditions are observed and cross the critical state line. The microstructures of undisturbed soil and post-cyclic specimens with different degrees of reconsolidation were quantitatively investigated. Besides that, the degree of influence of different factors on the post-cyclic undrained strength was analyzed. Based on the test results, the undrained shear strength with cyclic load-history was well predicted by existing models.

scholarly journals Accumulation of Pore Pressure in a Soft Clay Seabed around a Suction Anchor Subjected to Cyclic Loads

2019 ◽  
Vol 7 (9) ◽  
pp. 308 ◽  
Author(s):  
Li ◽  
Chen ◽  
Hu ◽  
Wang ◽  
Liu
Keyword(s):  
Pore Pressure ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Kinematic Hardening ◽  
Water Pressure ◽  
Soft Clay ◽  
Cyclic Loads ◽  
Distribution Characteristics ◽  
Excess Pore Water Pressure ◽  
Excess Pore

A suction anchor is an appealing anchoring solution for floating production. However, the possible effects of residual pore pressure can be rarely found any report so far in term of the research and design. In this study, the residual pore pressure distribution characteristics around the suction anchor subjected to vertical cyclic loads are investigated in a soft clay seabed, and a three-dimensional damage-dependent bounding surface model is also proposed. This model adopts the combined isotropic-kinematic hardening rule to achieve isotropic hardening and kinematic hardening of the boundary surface. The proposed model is validated against triaxial tests on anisotropically consolidated saturated clays and normally consolidated saturated clays. The analytical results show that the excess pore water pressure accumulates primarily on the outside of the suction anchor, whereas negative pore water pressure mainly on the inside. The maximum values of both sides appear in the lower part of the seabed. According to the distribution characteristics of the residual pore pressure, a perforated anchor is proposed to reduce the accumulation of excess pore water pressure. A comparative study generally shows that the perforated anchor can effectively reduce the accumulation of excess pore water pressure.

Stress–strain pattern–based criterion to assess cyclic shear resistance of soil from laboratory element tests

2016 ◽  
Vol 53 (9) ◽  
pp. 1460-1473 ◽  
Author(s):  
Dharma Wijewickreme ◽  
Achala Soysa
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Shear Stiffness ◽  
Large Strains ◽  
Fundamental Parameter ◽  
Stress Strain ◽  
Cyclic Shear ◽  
Excess Pore Water Pressure ◽  
Excess Pore

The cyclic shear response of soils is commonly examined using undrained (or constant-volume) laboratory element tests conducted using triaxial and direct simple shear (DSS) devices. The cyclic resistance ratio (CRR) from these tests is expressed in terms of the number of cycles of loading to reach unacceptable performance that is defined in terms of the attainment of a certain excess pore-water pressure and (or) strain level. While strain accumulation is generally commensurate with excess pore-water pressure, the definition of unacceptable performance in laboratory tests based purely on cyclic strain criteria is not robust. The shear stiffness is a more fundamental parameter in describing engineering performance than the excess pore-water pressure alone or shear strain alone; so far, no criterion has considered shear stiffness to determine CRR. Data from cyclic DSS tests indicate consistent differences inherent in the patterns between the stress–strain loops at initial and later stages of cyclic loading; instead of relatively “smooth” stress–strain loops in the initial parts of loading, nonsmooth changes in incremental stiffness showing “kinks” are notable in the stress–strain loops at large strains. The point of pattern change in a stress–strain loop provides a meaningful basis to determine the CRR (based on unacceptable performance) in cyclic shear tests.

Consolidation Theory for Composite Ground with Granular Columns Based on Different Calculation Models

2011 ◽  
Vol 261-263 ◽  
pp. 1534-1538
Author(s):  
Yu Guo Zhang ◽  
Ya Dong Bian ◽  
Kang He Xie
Keyword(s):  
Pore Water ◽  
Analytical Solutions ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Vertical Flow ◽  
Excess Pore Water Pressure ◽  
Consolidation Theory ◽  
Composite Ground ◽  
Granular Column ◽  
Excess Pore

The consolidation of the composite ground under non-uniformly distributed initial excess pore water pressure along depth was studied in two models which respectively considering both the radial and vertical flows in granular column and the vertical flow only in granular column, and the corresponding analytical solutions of the two models were presented and compared with each other. It shows that the distribution of initial excess pore water pressure has obvious influence on the consolidation of the composite ground with single drainage boundary, and the rate of consolidation considering the radial-vertical flow in granular column is faster than that considering the vertical flow only in granular column.

The Test Study to the Changes of Excess Pore Water Pressure during Precast Pile Construction

2012 ◽  
Vol 193-194 ◽  
pp. 1010-1013
Author(s):  
Shu Qing Zhao
Keyword(s):  
Pore Water ◽  
Clayey Soil ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Excess Pore Pressure ◽  
Soil Pressure ◽  
Excess Pore Water Pressure ◽  
Test Study ◽  
Excess Pore

The construct to precast pile in thick clayey soil can cause the accumulation of excess pore water pressure. The high excess pore pressure can make soil, buildings and pipes surrounded have large deflection, even make them injured. Combining with actual projects, this paper presents an in-situ model test on the changes of excess pore water pressure caused by precast pile construct. It is found that the radius of influence range for single pile driven is about 15m，the excess pore water pressure can reach or even exceed the above effective soil pressure, and there are two relatively stable stages.

A Practical Saturated Sand Elastic-Plastic Dynamic Constitutive Model and Application

2012 ◽  
Vol 446-449 ◽  
pp. 1621-1626 ◽  
Author(s):  
Yan Mei Zhang ◽  
Dong Hua Ruan
Keyword(s):  
Constitutive Model ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Stone Columns ◽  
Saturated Sand ◽  
Multidimensional Model ◽  
Excess Pore Water Pressure ◽  
Elastic Plastic ◽  
Excess Pore

A practical saturated sand elastic-plastic dynamic constitutive model was developed on the base of Handin-Drnevich class nonlinear lag model and multidimensional model. In this model, during the calculation of loading before soil reaches yielding, unloading and inverse loading, corrected Handin-Drnevich equivalent nonlinear model was adopted; after soil yielding, based on the idea of multidimensional model, the composite hardening law which combines isotropy hardening and follow-up hardening, corrected Mohr-Coulomb yielding criterion and correlation flow principle were adopted. A fully coupled three dimension effective stress dynamic analysis procedure was developed on the base of this model. The seismic response of liquefaction foundation reinforced by stone columns was analyzed by the developed procedure. The research shows that with the diameter of stone columns increasing, the excess pore water pressure in soil between piles decreases; with the spacing of columns increasing, the excess pore water pressure increases. The influence of both is major in middle and lower level of composite foundation.

Sign in / Sign up

Export Citation Format

Share Document