scholarly journals Three-Dimensional Finite Element Analysis of L4-5 Degenerative Lumbar Disc Traction under Different Pushing Heights

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Huaili Ding ◽  
Lijun Liao ◽  
Peichun Yan ◽  
Xiaolin Zhao ◽  
Min Li

Objective. To study and analyze the changes of intervertebral foramen height and area of the degenerative L4-5 intervertebral disc under different pushing heights by the finite element method. Methods. CT and MRI images of T12-S1 segments were obtained from a healthy volunteer who met the inclusion criteria. A DR machine was used to capture images of the lumbar lateral section before and after simultaneous pushing of the L4 and L5 spinous processes by manipulation called Daogaijinbei, and the measurement showed that the displacement changes of L4 and L5 were both approximately 10 cm, so the pushing height was set at 0–10 cm. A three-dimensional finite element model of the entire normal lumbar spine was established using Mimics 16.0, Geomagic Studio 2014, Hypermesh 13.0, MSC.Patran 2012, and so on. The disc height and nucleus area of the lumbar disc of the normal entire lumbar disc model were adjusted to establish models of the L4-5 disc with mild, moderate, and severe degeneration. Changes of disc height and area of the L4-5 degenerative intervertebral disc under different pushing heights were calculated. Results. The size of the L4-5 intervertebral foramen was analyzed from the height and area of the intervertebral foramen, and the results showed the following: (1) as for the normal lumbar disc and a lumbar of the L4-5 disc with mild and moderate degeneration, the height of the L4-5 intervertebral foramen and its area both increased during pushing between 0 and 8 cm. After the pushing height reached 8 cm, the height and area of the L4-5 intervertebral foramen gradually became stable; (2) as for the L4-5 disc with severe degeneration, during the process of pushing, the height and area of the L4-5 intervertebral foramen increased slightly, but this change was not obvious. Conclusions. After the spinal manipulation, the sizes of the L4-5 intervertebral foramen of the L4-5 disc with mild and moderate degeneration were significantly larger than those before pushing; in contrast, the size of L4-5 intervertebral foramen of the L4-5 disc with severe lumbar degeneration was not significantly changed.

2020 ◽  
Author(s):  
Kai Guo ◽  
Jiawei Lu ◽  
Ziqi Zhu ◽  
Beiduo Shen ◽  
Tongde Wu ◽  
...  

Abstract Background: ACDF is the main treatment of cervical disease. Adjacent Segment Degeneration (ASD) is the main complication of long-term follow-up of ACDF. we conduct a detailed study of ACDF by means of three-dimensional finite element analysis and find the effect of screw placement and location on the occurrence of ASD.Methods: The cervical computed tomography (CT) data (layer thickness of 0.625 mm) for a 30-year-old healthy male volunteer was collected. All the data were combined to create a C2-7 3D finite element model using Abaqus software. Based on the data and the actual surgical maneuver, a screw positioning model was established, in order to observe the cervical range of motion (ROM) with different positions of screw, as well as the pressure change of the adjacent segment intervertebral disc.Results: The proposed finite element model of cervical spine was effective, and ROM on all directions of C4-C6 segments changed after ACDF surgery. Under the same torque settings, compared with the control group, C2/3 segment rotational ROM increased; C2/3, C3/4 segments lateral flexion ROM also increased. Regarding the influence of screw positioning, it has limited influence on the ROM and The intervertebral disc pressure (IDP), and compared with different horizontal positions, different vertical positions imposed greater influence on the ROM and IDP. Conclusions: For ACDF surgery, positioning the screw at the anterior inferior part of the cervical vertebral body could provide more natural cervical ROM and the least IDP, while maintaining high biomechanical stability, and is more in line with human biomechanical requirements.


2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.


2011 ◽  
Vol 291-294 ◽  
pp. 3282-3286 ◽  
Author(s):  
Jiang Wei Wu ◽  
Peng Wang

In port crane industry, the surface hardening technique is widely used in order to improve the strength of wheel. But the hardening depth is chosen only by according to the experience, and the effect of different hardened depths is not studied theoretically. In this paper, the contact stresses in wheel with different hardening depth have been analyzed by applying three-dimensional finite element model. Based on this model, the ANSYS10.0 finite element software is used. The elastic wheel is used to verify the numerical results with the Hertz’s theory. Three different hardening depths, namely 10mm, 25mm and whole hardened wheel, under three different vertical loads were applied. The effect of hardening depth of a surface hardened wheel is discussed by comparing the contact stresses and contact areas from the numerical results.


2020 ◽  
Vol 21 (1) ◽  
Author(s):  
Zhun Xu ◽  
Yikai Li ◽  
Shaoqun Zhang ◽  
Liqing Liao ◽  
Kai Wu ◽  
...  

Abstract Background Clinical studies have found that manipulations have a good clinical effect on sacroiliac joint (SIJ) pain without specific causes. However, the specific mechanisms underlying the effect of manipulations are still unclear. The purpose of this study was to investigate the effects of three common manipulations on the stresses and displacements of the normal SIJ and the strains of the surrounding ligaments. Methods A three-dimensional finite element model of the pelvis-femur was developed. The manipulations of hip and knee flexion (MHKF), oblique pulling (MOP), and lower limb hyperextension (MLLH) were simulated. The stresses and displacements of the SIJ and the strains of the surrounding ligaments were analyzed during the three manipulations. Results MOP produced the highest stress on the left SIJ, at 6.6 MPa, while MHKF produced the lowest stress on the right SIJ, at 1.5 MPa. The displacements of the SIJ were all less than 1 mm during the three manipulations. The three manipulations caused different degrees of ligament strain around the SIJ, and MOP produced the greatest straining of the ligaments. Conclusion The three manipulations all produced small displacements of the SIJ and different degrees of ligament strains, which might be the mechanism through which they relieve SIJ pain. MOP produced the largest displacement and the greatest ligament strains.


Author(s):  
Sunil Kumar Sharma ◽  
Jaesun Lee

Railways are very efficient mode of transportation. Speed limits of the railways and loads they carry are increasing rapidly. Due to some advantages, the insulated rail joints are still the part of a rail-track system. However, a high rate of failure of joints puts the railway track at risk. Therefore, a detailed study of these joints is required. In this paper, a three-dimensional finite element model of rail-fishplate joint is created using Abaqus - a finite element method-based software. Stresses in fishplate and bolts due to wheel impact are analysed by coupling implicit and explicit methods. It is found that bolts are a critical part of a joint due to stresses and vibrations to which they are subjected. The large number of stresses and vibration can result into loosening of bolts.


Author(s):  
Cagri Mollamahmutoglu ◽  
Idris Bedirhanoglu

In this study, the performance of a damaged dam was evaluated through a three-dimensional finite element model. The dam is located in Derbendikhan city of Northern Iraq and damaged during a 7.3 magnitude earthquake which was happened 30 kilometers south of Halabja city. Derbendikhan dam which was built between the years 1956-1961 is a clay-core rock fill dam. The damage of the dam was investigated at the site right after the earthquake and some cracks were observed in the main body of the dam. The main goal of this work is to present the results of the survey which was conducted at the site and investigating the damage development mechanism through a realistic three-dimensional finite element model of the dam. As complying with the observations at the site, the finite element analysis has shown that the primary failure mechanism is due to the separation of the core and rock fill sections at the downstream side of the dam.


2012 ◽  
Vol 446-449 ◽  
pp. 2206-2209
Author(s):  
Jin Long Wang

Three-dimensional finite element model of the mine escape capsule is established. With the different values of explosion shock waves, simulation analysis of the entry locker is performed by using ABAQUS. The simulation results indicate that the mine escape capsule is safe and available if the surge pressure of shock waves is less than 3.5Mpa.


Author(s):  
S. Ismonov ◽  
S. R. Daniewicz ◽  
J. C. Newman ◽  
M. R. Hill ◽  
M. R. Urban

A cold expansion process is used to prolong the fatigue life of a structure under cyclic loadings. The process produces a beneficial compressive residual stress zone in the hole vicinity, which retards the initiation and propagation of the crack at the hole edge. In this study, a three-dimensional finite element model of the split-sleeve cold expansion process was developed to predict the resulting residual stress field. A thin rectangular aluminum sheet with a centrally located hole was considered. A rigid mandrel and an elastic steel split sleeve were explicitly modeled with the appropriate contact elements at the interfaces between the mandrel, the sleeve, and the hole. Geometrical and material nonlinearities were included. The simulation results were compared with experimental measurements of the residual stress. The influence of friction and the prescribed boundary conditions for the sheet were studied. Differences between the split-sleeve- and the non-split-sleeve model solutions are discussed.


2010 ◽  
Vol 118-120 ◽  
pp. 147-150
Author(s):  
Da Zhao Yu ◽  
Yue Liang Chen ◽  
Yong Gao ◽  
Wen Lin Liu ◽  
Zhong Hu Jia

Three-dimensional finite element model of a cracked bolted joint has been developed in the non-linear finite element code MSC.Marc and attempts were made to validate it by comparing results with those of experiments and other finite element. Issues in modeling the contact between the joint parts, which affect the accuracy and efficiency of the model, were presented. Experimental measurements of load transfer were compared with results from finite element analysis. The results show that three-dimensional finite element model of cracked bolted joint can produce results in close agreement with experiment. Three-dimensional effects such as bolt titling, seconding and through-thickness variations in stress and strain are well represented by such models. Three-dimensional finite element analysis was also used to study the effects of hole mod and crack on the load transfer behaviour of single lap bolted joints. The results show that hole mode has big effect on load transfer of cracked bolted joint. In the whole progress of crack growth, the load transfer through bolt 1 decrease, and almost all of the load duduction of bolt 1 transfer into blot 2 rather than into bolt 3.


2020 ◽  
Author(s):  
Zhun Xu ◽  
Yikai Li ◽  
Shaoqun Zhang ◽  
Liqing Liao ◽  
Kai Wu ◽  
...  

Abstract BackgroundClinical studies have found that manipulations have a good clinical effect on sacroiliac joint (SIJ) pain without specific causes. However, the specific mechanisms underlying the effect of manipulations are still unclear. The purpose of this study was to investigate the effects of three common manipulations on the stresses and displacements of the SIJ and the strains of the surrounding ligaments.MethodsA three-dimensional finite element model of the pelvis-femur was developed. The manipulations of hip and knee flexion (MHKF), oblique pulling (MOP), and lower limb hyperextension (MLLH) were simulated. The stresses and displacements of the SIJ and the strains of the surrounding ligaments were analyzed during the three manipulations.ResultsMOP produced the highest stress on the left SIJ, at 6.6 MPa, while MHKF produced the lowest stress on the right SIJ, at 1.5 MPa. The displacements of the SIJ were all less than 1 mm during the three manipulations. The three manipulations caused different degrees of ligament strain around the SIJ, and MOP produced the greatest straining of the ligaments.ConclusionThe three manipulations all produced small displacements of the SIJ and different degrees of ligament strains, which might be the mechanism through which they relieve SIJ pain. MOP may be the most effective of these manual therapies.


Sign in / Sign up

Export Citation Format

Share Document