scholarly journals Statistical Modeling and Kinetic Studies on the Adsorption of Reactive Red 2 by a Low-Cost Adsorbent: Grape Waste-Based Activated Carbon Using Sulfuric Acid Activator-Assisted Thermal Activation

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Seyyed Alireza Mousavi ◽  
Davood Shahbazi ◽  
Arezoo Mahmoudi ◽  
Parviz Mohammadi ◽  
Tooraj Massahi
Keyword(s):  
Activated Carbon ◽  
Statistical Modeling ◽  
Low Cost ◽  
Dye Adsorption ◽  
Kinetic Studies ◽  
Type I ◽  
Order Kinetic ◽  
Grape Waste ◽  
Pseudosecond Order ◽  
Reactive Red 2

The efficiency of activated carbon produced from grape waste as a low-cost, nontoxic, and available adsorbent to remove Reactive Red 2 from aqueous solution has been investigated. The prepared activated carbon has been characterized by FTIR, SEM, and BET. The results of characterization indicate the successful conversion of grape waste into mesoporous AC with desirable surface area consist of different functional groups. The results of statistical modeling displayed high R 2 value of 0.97% for dye removal that shows the developed model has acceptable accuracy. The effect of independent variables indicated that the highest adsorption (96.83%) obtained at pH 3, adsorbent dosage of 12.25 g/L, and initial dye concentration of 100 mg/L when the adsorption time was 90 min. The results of isotherms modeling showed that the data fit well with the Langmuir (type II). The kinetic studies using pseudofirst-order and pseudosecond-order models pointed out that the type (I) of pseudosecond-order kinetic model provided the best fit to the adsorption data. Parameters of thermodynamics including Gibbs energy ( Δ G ° ) and k o were calculated. The values of Δ G ° indicated that the dye adsorption of RR2 is spontaneous. The agricultural wastes due to special points such as low-cost, availability, and high ability to produce an adsorbent with high efficiency to remove dye can be proposed for water and wastewater treatment.

scholarly journals Microporous activated carbon developed from KOH activated biomass waste: surface mechanistic study of methylene blue dye adsorption

2021 ◽  
Author(s):  
Ali H. Jawad ◽  
Ahmed Saud Abdulhameed ◽  
Noor Nazihah Bahrudin ◽  
Nurul Nadiah Mohd Firdaus Hum ◽  
S. N. Surip ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Surface Area ◽  
Sugarcane Bagasse ◽  
High Surface ◽  
High Surface Area ◽  
Dye Adsorption ◽  
Type I ◽  
Order Kinetic ◽  
Bagasse Waste

Abstract In this work, sugarcane bagasse waste (SBW) was used as a lignocellulosic precursor to develop a high surface area activated carbon (AC) by thermal treatment of the SBW impregnated with KOH. This sugarcane bagasse waste activated carbon (SBWAC) was characterized by means of crystallinity, porosity, surface morphology and functional groups availability. The SBWAC exhibited Type I isotherm which corresponds to microporosity with high specific surface area of 709.3 m2/g and 6.6 nm of mean pore diameter. Further application of SBWAC as an adsorbent for methylene blue (MB) dye removal demonstrated that the adsorption process closely followed the pseudo-second order kinetic and Freundlich isotherm models. On the other hand, thermodynamic study revealed the endothermic nature and spontaneity of MB dye adsorption on SBWAC with high acquired adsorption capacity (136.5 mg/g). The MB dye adsorption onto SBWAC possibly involved electrostatic interaction, H-bonding and π-π interaction. This work demonstrates SBW as a potential lignocellulosic precursor to produce high surface area AC that can potentially remove more cationic dyes from the aqueous environment.

scholarly journals Reactive dyes adsorption via Citrus hystrix peel powder and Zea mays cob powder: characterization, isotherm and kinetic studies

2019 ◽  
Vol 10 (1) ◽  
pp. 4803-4810
Keyword(s):  
Zea Mays ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Kinetic Studies ◽  
Order Kinetic ◽  
Lime Peel ◽  
Dyes Adsorption ◽  
Reactive Red 2 ◽  
Physical And Chemical ◽  
Solution Acidity

Adsorption is one of the generally used treatment methods due to the low-cost, high removal effect and simple design The aim of the study was to investigate the adsorption efficiency of lignocellulosic waste such as lime peel (Citrus hystrix) and CC (Zea mays) for removal of Reactive Violet 5 (RV5) and Reactive Red 2 (RR2) dyes. The physical and chemical characteristics of the adsorbents were analyses by using Fourier transform infrared (FTIR) and scanning electron microscopy (SEM). Additionally, the solution acidity, adsorbent mass, duration of adsorption, and dye concentration were evaluated with isotherm and kinetic study to determine the mechanism of adsorption. The removal of RV5 for lime peel and CC achieved to 50 % and 48 % while the removal of RR2 for lime peel and CC reached 53 % and 46 %. The highest adsorption capacity for both adsorbents was 4.29 mg/g and 6.14 mg/g. In terms of physical characteristics, the adsorbent had large surface area that adsorbs more dyes in same amount of dye concentration. The results showed that Freundlich isotherm and Pseudo-first-order kinetic models were best fitted to the adsorption process with R2 value of 0.9974 and R2 value of 0.9919.

scholarly journals Organic Dyes Adsorption on the Almond Shell (Prunus dulcis) as Agricultural Solid Waste from Aqueous Solution in Single and Binary Mixture Systems

2021 ◽  
Vol 12 (2) ◽  
pp. 2022-2040
Keyword(s):  
Aqueous Solution ◽  
Binary Mixture ◽  
Contact Time ◽  
Binary Systems ◽  
Organic Dyes ◽  
Low Cost ◽  
Kinetic Studies ◽  
Prunus Dulcis ◽  
Order Kinetic ◽  
Almond Shell

Almond shell (AS) is a low-cost adsorbent used in this study for the removal of methylene blue (MB), crystal violet (CV), and Congo red (CR) from an aqueous solution in single and mixture binary systems. The low-cost adsorbent was characterized by FTIR and SEM analysis. The effects of AS dose, contact time, initial dye concentration, pH, and temperature on MB, CV, and CR adsorption were studied in a single system. In a binary system, the MB, CV, and CR were removed from the mixture of MB+CR, CV+MB, and CV+CR with a percentage in volume ranging from 0 to 100 % in MB and CV, and CR. Kinetic studies showed rapid sorption following a second-order kinetic model with of contact time of 10 min. The modulation of adsorption isotherms showed that retention follows the Langmuir model. The thermodynamic parameters proved that the MB, CV, and CR adsorption process was feasible, spontaneous, and exothermic. The synergy adsorption between dyes in a binary mixture of MB+CR and CV+CR, while the competition adsorption between dyes in a binary mixture of MB+ CV.

scholarly journals Fast and Effective Catalytic Degradation of an Organic Dye by Eco-friendly Capped ZnS and Mn doped ZnS nanocrystals

2021 ◽  
Author(s):  
Sabri Ouni ◽  
Naim Bel Haj Mohamed ◽  
Noureddine Chaaben ◽  
Adrian Bonilla-Petriciolet ◽  
Mohamed Haouari
Keyword(s):  
Statistical Physics ◽  
Thioglycolic Acid ◽  
Dye Degradation ◽  
Low Cost ◽  
Quantum Confinement Effect ◽  
Dye Adsorption ◽  
Blue Shift ◽  
Order Kinetic ◽  
Zns Nanocrystals ◽  
Mn Doped

Abstract Undoped and Mn-doped ZnS nanocrystals encapsulated with thioglycolic acid were synthetized and characterized with different techniques, and finally tested in the photodegradation of a methyl orange in aqueous solution under UV and sunlight irradiations. FTIR and X-ray diffraction results confirmed the functionalization of these nanocrystals surface by thioglycolic acid and the formation of crystalline structures of ZnS and Mn-doped ZnS with cubic and hexagonal phases. Calculated average size of ZnS nanocrystals was in the range of 2 - 3 nm. It was observed a blue shift of the absorbance threshold and the estimated bandgap energies were higher than that of Bulk ZnS thus confirming the quantum confinement effect of charge carriers. Photoluminescence spectra of ZnS nanocrystals exhibited emission in the range of 410- 490 nm and the appearance of an additional emission band around 580 nm (2.13eV) connected to the 4𝑇1→ 6𝐴1 transition of the Mn2+ions. Photodegradation of methylene orange with undoped and Mn-doped ZnS-TGA nanocrystals was investigated. Dye adsorption prior to photocatalysis using nanocrystals was studied via kinetic experiments and statistical physics models. The maximum dye adsorption capacity on doped ZnS-TGA was ~ 26.98 mg/g. The adsorption kinetic was found to follow the pseudo-second-order kinetic model.According to the statistical physics results, the calculated adsorption energy was 22.47-23.47 kJ/mol and it showed that the dye adsorption was associated to the hydrogen interaction where the removal process was feasible and multi-molecular. The photocatalytic activity of undoped ZnS nanoparticles under UV irradiation showed better efficiency than doped nanocrystals thus indicating that manganese doping generated a dropping of the photocatalytic degradation of the dye. Dye degradation efficiency of 81.37% using ZnS-TGA nanocrystals was achieved after 6 min, which indicated that ZnMnS-TGA nanocrystals may be considered as an alternative low cost and environmental friendly material for facing water pollution caused by organic compounds via photodegradation processes.

scholarly journals New Activated Carbon from Mine Coal for Adsorption of Dye in Simulated Water or Multiple Heavy Metals in Real Wastewater

Materials ◽  
2020 ◽  
Vol 13 (11) ◽  
pp. 2498 ◽  
Author(s):  
Marwa Elkady ◽  
Hassan Shokry ◽  
Hesham Hamad
Keyword(s):  
Activated Carbon ◽  
Nitric Acid ◽  
Metal Ions ◽  
Low Cost ◽  
Dye Adsorption ◽  
Chemical Properties ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Physico Chemical ◽  
Multiple Heavy Metals

Nano-activated carbon (NAC) prepared from El-Maghara mine coal were modified with nitric acid solution. Their physico-chemical properties were investigated in terms of methylene blue (MB) adsorption, FTIR, and metal adsorption. Upon oxidation of the ACS with nitric acid, surface oxide groups were observed in the FTIR spectra by absorption peaks at 1750–1250 cm−1. The optimum processes parameters include HNO3/AC ratio (wt./wt.) of 20, oxidation time of 2 h, and the concentration of HNO3 of 10% reaching the maximum adsorption capacity of MB dye. Also, the prepared NAC was characterized by SEM, EDX, TEM, Raman Spectroscopy, and BET analyses. The batch adsorption of MB dye from solution was used for monitoring the behavior of the most proper produced NAC. Equilibrium isotherms of MB dye adsorption on NAC materials were acquired and the results discussed in relation to their surface chemistry. Langmuir model recorded the best interpretation of the dye adsorption data. Also, NAC was evaluated for simultaneous adsorption of six different metal ions (Fe2+, Ni2+, Mn2+, Pb2+, Cu2+, and Zn2+) that represented contaminates in petrochemical industrial wastewater. The results indicated that the extracted NAC from El-Maghara mine coal is considered as an efficient low-cost adsorbent material for remediation in both basic dyes and metal ions from the polluted solutions.

scholarly journals Adsorption of Hexavalent Chromium from Aqueous Solution Using Chemically Activated Carbon Prepared from Locally Available Waste of Bamboo (Oxytenanthera abyssinica)

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Tamirat Dula ◽  
Khalid Siraj ◽  
Shimeles Addisu Kitte
Keyword(s):  
Activated Carbon ◽  
Hexavalent Chromium ◽  
Freundlich Isotherm ◽  
Kinetic Studies ◽  
Batch Adsorption ◽  
Koh Activation ◽  
Order Kinetic ◽  
Oxytenanthera Abyssinica ◽  
Equilibrium Data ◽  
Order Kinetic Model

This study reports on the adsorption of Hexavalent Chromium from aqueous solutions using activated carbon prepared from bamboo (Oxytenanthera abyssinica) waste by KOH activation heating in an electrical furnace at 1073 K for 3 hrs. Batch adsorption experiments were also carried out as a function of pH, contact time, initial concentration of the adsorbate, adsorbent dosage, and temperature of the solution. Kinetic studies of the data showed that the adsorption follows the pseudo-second-order kinetic model. Thermodynamic parameters showed that adsorption on the surface of BWAC was feasible, spontaneous in nature, and exothermic between temperatures of 298 and 318 K. The equilibrium data better fitted the Freundlich isotherm model for studying the adsorption behavior of Hexavalent Chromium by BWAC. IR spectrum for loaded and unloaded BWAC was obtained using FT-IR spectrophotometer. Adsorption efficiency and capacity of Hexavalent Chromium were found to be 98.28% at pH 2 and 59.23 mg/g at 300 K.

Removal of Methylene Blue by Adsorption Process - A Comparative Study

2011 ◽  
Vol 699 ◽  
pp. 245-264 ◽  
Author(s):  
A. Xavier ◽  
J. Gandhi Rajan ◽  
D. Usha ◽  
R Sathya
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Adsorption Process ◽  
Activated Carbons ◽  
Low Cost ◽  
Kinetic Equations ◽  
Dye Adsorption ◽  
Industrial Wastes ◽  
Blue Dye ◽  
Molecular Formula

Methylene blue is a heterocyclic aromatic chemical compound with the molecular formula C16H18N3SCl. It has used in the biology and chemistry field. At room temperature, it appears as a solid, odourless dark green powder that yields blue solution when dissolved in water. As a part of removal of methylene blue dye from textile and leather industrial wastes, using activated carbon as adsorbents namely, commercial activated carbon (CAC), rose apple carbon (RAC), coconut shell carbon (CSC) and saw dust carbon (SDC). The percentage of Methylene blue adsorbed increases with decrease in initial concentration and particle size of adsorbent and increased with increase in contact time, temperature and dose of adsorbents. The pH is highly sensitive for dye adsorption process. The adsorption process followed first order kinetics and the adsorption data the modeled with Freundlich and Langmuir isotherms. The first kinetic equations like Natarajan Khalaf, Lagergren, Bhattacharya and Venkobhachar and intra particle diffusion were found to be applicable. A comparative account of the adsorption capacity of various carbons has been made. These activated carbons are alternative to commercial AC for the removal dyes in General and MB is particular. These results are reported highly efficient and effective and low cost adsorbent for the MB. The thermodynamics parameters are also studied and it obeys spontaneous process. The results are confirmed by before and after adsorption process with the help of the following instrumental techniques viz., FT-IR, UV-Visible Spectrophotometer and SEM photos.

scholarly journals Methylene blue removal using a low-cost activated carbon adsorbent from tobacco stems: kinetic and equilibrium studies

2017 ◽  
Vol 75 (10) ◽  
pp. 2390-2402 ◽  
Author(s):  
Bellington Mudyawabikwa ◽  
Henry H. Mungondori ◽  
Lilian Tichagwa ◽  
David M. Katwire
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Radiation Power ◽  
Low Cost ◽  
Carbon Adsorbent ◽  
Point Of Zero Charge ◽  
Order Kinetic ◽  
Optimum Conditions ◽  
Equilibrium Studies ◽  
Mb Adsorption

The aim of this study was to prepare activated carbon from tobacco stalks using microwave heating. The prepared activated carbon was applied as an adsorbent in methylene blue (MB) removal from water. The optimum conditions for activated carbon preparation were a radiation power of 280 W for a period of 6 minutes after the impregnation of the precursor material with 30% ZnCl2 for 24 hours. The activated carbon yield and iodine number were 49.43% and 1,264.51 mg/g respectively. The activated carbon also had a point of zero charge of 5.81 with an adsorption capacity of 123.45 mg/g for MB. The optimum conditions for MB adsorption were a pH of 6.5 with an adsorbent dosage of 0.2 g/50 mL at 25 °C. The MB adsorption kinetics followed the pseudo second order kinetic model with the intra-particle diffusion model suggesting a two-step adsorption mechanism. The adsorption data also fitted well within the Langmuir adsorption isotherm model. Tobacco stalks can successfully be turned into an economically important product.

Equilibrium and Kinetic Studies of Benzene and Toluene Adsorption onto Microwave Irradiated-Coconut Shell Activated Carbon

2014 ◽  
Vol 1043 ◽  
pp. 219-223 ◽  
Author(s):  
Noor Shawal Nasri ◽  
Jibril Mohammed ◽  
Muhammad Abbas Ahmad Zaini ◽  
Usman Dadum Hamza ◽  
Husna Mohd. Zain ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Kinetic Studies ◽  
Coconut Shell ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Volatile Organic ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Coconut Shell Activated Carbon

Concern about environmental protection has increased over the years and the presence of volatile organic compounds (VOCs) in water poses a threat to the environment. In this study, coconut shell activated carbon (PHAC) was produced by potassium hydroxide activation via microwave for benzene and toluene removal. Equilibrium data were fitted to Langmuir, Freundlich and Tempkin isotherms with all the models having R2 > 0.94. The equilibrium data were best fitted by Langmuir isotherm, with maximum adsorption capacity of 212 and 238mg/g for benzene and toluene, respectively. The equilibrium parameter (RL) falls between 0 and 1 confirming the favourability of the Langmuir model. Pseudo-second-order kinetic model best fitted the kinetic data. The PHAC produced can be used to remediate water polluted by VOCs.

Sign in / Sign up

Export Citation Format

Share Document