scholarly journals Mechanics of Materials Natural Fibers Technology on Thermal Properties of Polymer

2022 ◽  
Vol 2022 ◽  
pp. 1-5
Author(s):  
Malik Bader Alazzam ◽  
Fahima Hajjej ◽  
Ahmed S AlGhamdi ◽  
Sarra Ayouni ◽  
Md Adnan Rahman
Keyword(s):  
Thermal Conductivity ◽  
Unsaturated Polyester ◽  
Natural Fibers ◽  
Thermal Characteristics ◽  
Theoretical Data ◽  
Numerical Data ◽  
The Other ◽  
Comsol Multiphysics ◽  
Mechanics Of Materials ◽  
The Mean

The thermal characteristics of polymathic methacrylate combined with unsaturated polyester were determined by numerical and experimental research. Models for numerically investigating the parameters of thermal conductivity, specific heat capacity, and thermal diffusivity were developed using COMSOL Multiphysics. The numerical data were then compared to experimental results for the same material using the same measurements to ensure that they were correct. By comparing the thermal conductivity data to two sets of theoretical data, the results were confirmed. The COMSOL models were quite close to the experimental data, with just minor differences between the three models. One set of theoretical data coincided with the mean of the other data, while the second set revealed a significant departure below the other data.

Multi-Center Study of Thromboplastin Calibration Precision – Influence of Reagent Species, Composition, and International Sensitivity Index (ISI)

1993 ◽  
Vol 69 (01) ◽  
pp. 035-040 ◽  
Author(s):  
A M H P van den Besselaar ◽  
R M Bertina
Keyword(s):  
Oral Anticoagulants ◽  
International Normalized Ratio ◽  
The Other ◽  
World Health ◽  
Rabbit Brain ◽  
Sensitivity Index ◽  
Bovine Plasma ◽  
Significant Difference ◽  
The Mean ◽  
International Sensitivity Index

SummaryFour thromboplastin reagents were tested by 18 laboratories in Europe, North-America, and Australasia, according to a detailed protocol. One thromboplastin was the International Reference Preparation for ox brain thromboplastin combined with adsorbed bovine plasma (coded OBT/79), and the second was a certified reference material for rabbit brain thromboplastin, plain (coded CRM 149R). The other two thromboplastin reagents were another rabbit plain brain thromboplastin (RP) with a lower ISI than CRM 149R and a rabbit brain thromboplastin combined with adsorbed bovine plasma (RC). Calibration of the latter two reagents was performed according to methods recommended by the World Health Organization (W. H. O.).The purpose of this study was to answer the following questions: 1) Is the calibration of the RC reagent more precise against the bovine/combined (OBT/79) than against the rabbit/plain reagent (CRM 149R)? 2) Is the precision of calibration influenced by the magnitude of the International Sensitivity Index (ISI)?The lowest inter-laboratory variation of ISI was observed in the calibration of the rabbit/plain reagent (RP) against the other rabbit/plain reagent (CRM 149R) (CV 1.6%). The highest interlaboratory variation was obtained in the calibration of rabbit/plain (RP) against bovine/combined (OBT/79) (CV 5.1%). In the calibration of the rabbit/combined (RC) reagent, there was no difference in precision between OBT/79 (CV 4.3%) and CRM 149R (CV 4.2%). Furthermore, there was no significant difference in the precision of the ISI of RC obtained with CRM 149R (ISI = 1.343) and the rabbit/plain (RP) reagent with ISI = 1.14. In conclusion, the calibration of RC could be performed with similar precision with either OBT/79 or CRM 149R, or RP.The mean ISI values calculated with OBT/79 and CRM 149R were practically identical, indicating that there is no bias in the ISI of these reference preparations and that these reference preparations have been stable since their original calibration studies in 1979 and 1987, respectively.International Normalized Ratio (INR) equivalents were calculated for a lyophilized control plasma derived from patients treated with oral anticoagulants. There were small but significant differences in the mean INR equivalents between the bovine and rabbit thromboplastins. There were no differences in the interlaboratory variation of the INR equivalents, when the four thromboplastins were compared.

Prothrombin Time Standardization: Report of the Expert Panel on Oral Anticoagulant Control

1979 ◽  
Vol 42 (04) ◽  
pp. 1073-1114 ◽  
Keyword(s):  
Prothrombin Time ◽  
Expert Panel ◽  
The Other ◽  
Rabbit Brain ◽  
Calibration Constant ◽  
Freeze Dried ◽  
The Mean ◽  
Point Of Intersection ◽  
And Control ◽  
Standardization Report

SummaryIn collaborative experiments in 199 laboratories, nine commercial thromboplastins, four thromboplastins held by the National Institute for Biological Standards and Control (NIBS & C), London and the British Comparative Thromboplastin were tested on fresh normal and coumarin plasmas, and on three series of freeze-dried plasmas. One of these was made from coumarin plasmas and the other two were prepared from normal plasmas; in each series, one plasma was normal and the other two represented different degrees of coumarin defect.Each thromboplastin was calibrated against NIBS&C rabbit brain 70/178, from the slope of the line joining the origin to the point of intersection of the mean ratios of coumarin/normal prothrombin times when the ratios obtained with the two thromboplastins on the same fresh plasmas were plotted against each other. From previous evidence, the slopes were calculated which would have been obtained against the NIBS&C “research standard” thromboplastin 67/40, and termed the “calibration constant” of each thromboplastin. Values obtained from the freeze-dried coumarin plasmas gave generally similar results to those from fresh plasmas for all thromboplastins, whereas values from the artificial plasmas agreed with those from fresh plasmas only when similar thromboplastins were being compared.Taking into account the slopes of the calibration lines and the variation between laboratories, precision in obtaining a patient’s prothrombin time was similar for all thromboplastins.

Platelet Suruival and Function in Rats with Enhanced Thrombotic Tendency

1985 ◽  
Vol 54 (04) ◽  
pp. 739-743 ◽  
Author(s):  
Federica Delaini ◽  
Elisabetta Dejana ◽  
Ine Reyers ◽  
Elisa Vicenzi ◽  
Germana De Bellis Vitti ◽  
...  
Keyword(s):  
Arachidonic Acid ◽  
Nephrotic Syndrome ◽  
Platelet Function ◽  
Laboratory Tests ◽  
Thrombus Formation ◽  
The Other ◽  
Mean Survival Time ◽  
The Mean ◽  
And Function ◽  
Thrombotic Tendency

SummaryWe have investigated the relevance of some laboratory tests of platelet function in predicting conditions of thrombotic tendency. For this purpose, we studied platelet survival, platelet aggregation in response to different stimuli, TxB2 and 6-keto-PGFlα production in serum of rats bearing a nephrotic syndrome induced by adriamycin. These animals show a heavy predisposition to the development of both arterial and venous thrombosis. The mean survival time was normal in nephrotic rats in comparison to controls. As to aggregation tests, a lower aggregating response was found in ADR-treated rats using ADP or collagen as stimulating agents. With arachidonic acid (AA) we observed similar aggregating responses at lower A A concentrations, whereas at higher AA concentrations a significantly lower response was found in nephrotic rats, despite their higher TxB2 production. Also TxB2 and 6-keto-PGFlα levels in serum of nephrotic rats were significantly higher than in controls. No consistent differences were found in PGI2-activity generated by vessels of control or nephrotic rats.These data show that platelet function may appear normal or even impaired in rats with a markedly increased thrombotic tendency. On the other hand, the significance of high TxB2 levels in connection with mechanisms leading to thrombus formation remains a controversial issue.

Voronoi Analysis of a Soccer Game

2004 ◽  
Vol 9 (3) ◽  
pp. 233-240 ◽  
Author(s):  
S. Kim
Keyword(s):  
Collective Behavior ◽  
Quantitative Assessment ◽  
The Other ◽  
Analysis Method ◽  
Random System ◽  
Soccer Game ◽  
Voronoi Polygons ◽  
The Mean

This paper describes a Voronoi analysis method to analyze a soccer game. It is important for us to know the quantitative assessment of contribution done by a player or a team in the game as an individual or collective behavior. The mean numbers of vertices are reported to be 5–6, which is a little less than those of a perfect random system. Voronoi polygons areas can be used in evaluating the dominance of a team over the other. By introducing an excess Voronoi area, we can draw some fruitful results to appraise a player or a team rather quantitatively.

A Study of Some Mechanical and Physical Properties for Palm Fiber/Polyester Composite

2020 ◽  
Vol 38 (3B) ◽  
pp. 104-114
Author(s):  
Samah M. Hussein
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Dielectric Constant ◽  
Date Palm ◽  
Volume Fraction ◽  
Unsaturated Polyester ◽  
Dielectric Strength ◽  
Palm Fiber ◽  
Mechanical And Physical Properties ◽  
Polyester Composite

This research has been done by reinforcing the matrix (unsaturated polyester) resin with natural material (date palm fiber (DPF)). The fibers were exposure to alkali treatment before reinforcement. The samples have been prepared by using hand lay-up technique with fiber volume fraction of (10%, 20% and 30%). After preparation of the mechanical and physical properties have been studied such as, compression, flexural, impact strength, thermal conductivity, Dielectric constant and dielectric strength. The polyester composite reinforced with date palm fiber at volume fraction (10% and 20%) has good mechanical properties rather than pure unsaturated polyester material, while the composite reinforced with 30% Vf present poor mechanical properties. Thermal conductivity results indicated insulator composite behavior. The effect of present fiber polar group induces of decreasing in dielectric strength, and increasing dielectric constant. The reinforcement composite 20% Vf showed the best results in mechanical, thermal and electrical properties.

Solid, slightly soluble phosphorus compounds as nutrient source in activated sludge treatment of forest industry wastewaters

1997 ◽  
Vol 35 (2-3) ◽  
pp. 131-138 ◽  
Author(s):  
Pirjo-Riitta Rantala ◽  
Hannu Wirola
Keyword(s):  
Activated Sludge ◽  
The Other ◽  
Phosphorus Compounds ◽  
Forest Industry ◽  
Phosphorus Concentration ◽  
Nutrient Source ◽  
Sludge Treatment ◽  
Grain Sizes ◽  
Soluble Phosphorus ◽  
The Mean

The aim of the study was to determine if solid, slightly soluble compounds can be used as nutrient source in activated sludge treatment plants instead of liquid phosphoric acid. Four different solid materials were tested in lab-scale solubility tests to find compounds which are least soluble. Two materials were chosen for further studies: apatite and raw phosphate. The use of apatite and raw phosphate as nutrient source was studied in lab-scale activated sludge reactors along with a control reactor where phosphorus was added in liquid form. The phosphorus dosage, measured as elementary phosphorus, was the same for all three reactors. The reactors were fed with pre-clarified chemi-thermomechanical pulp mill (CTMP) wastewater. There were no significant differences in the reductions of organic matter between the three reactors. The mean effluent concentration of total phosphorus was 3 mg P/l in the control reactor and less than 1 mg P/1 in the other two reactors. The soluble phosphorus concentration was more than 2 mg P/l in the control reactor and less than 0.5 mg P/l in the other two. Apatite was an even better nutrient source than raw phosphate. Further lab-scale tests were conducted using two different grain sizes of apatite. No significant differences were found between the studied grain sizes (<0.074 mm and 0.074 mm-0.125 mm). Apatite was then used in full-scale at a CTMP-mill two different times. The experiments showed that the mean concentrations of phosphorus can be reduced radically by using apatite as a nutrient source instead of liquid phosphorus. Solid phosphorus compounds are a viable alternative to reduce the phosphorus load from forest industry wastewater treatment plants.

Maximizing Heat Transfer Through Joint Fin Systems

2005 ◽  
Vol 128 (2) ◽  
pp. 203-206 ◽  
Author(s):  
A.-R. A. Khaled
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Thermal Performance ◽  
Critical Length ◽  
The Other ◽  
Rigid Fixation ◽  
Convection Coefficient ◽  
Heat Transfer Characteristics ◽  
Cold Side ◽  
Transfer Characteristics

Heat transfer through joint fins is modeled and analyzed analytically in this work. The terminology “joint fin systems” is used to refer to extending surfaces that are exposed to two different convective media from its both ends. It is found that heat transfer through joint fins is maximized at certain critical lengths of each portion (the receiver fin portion which faces the hot side and the sender fin portion that faces the cold side of the convective media). The critical length of each portion of joint fins is increased as the convection coefficient of the other fin portion increases. At a certain value of the thermal conductivity of the sender fin portion, the critical length for the receiver fin portion may be reduced while heat transfer is maximized. This value depends on the convection coefficient for both fin portions. Thermal performance of joint fins is increased as both thermal conductivity of the sender fin portion or its convection coefficient increases. This work shows that the design of machine components such as bolts, screws, and others can be improved to achieve favorable heat transfer characteristics in addition to its main functions such as rigid fixation properties.

scholarly journals The Effect of Route Choice in Children’s Exposure to Ultrafine Particles Whilst Walking to School

2021 ◽  
Vol 18 (15) ◽  
pp. 7808
Author(s):  
Mehrdad Rafiepourgatabi ◽  
Alistair Woodward ◽  
Jennifer A. Salmond ◽  
Kim Natasha Dirks
Keyword(s):  
Ultrafine Particles ◽  
Route Choice ◽  
The Other ◽  
Close Proximity ◽  
Public Health Officials ◽  
Risk Of Exposure ◽  
The Mean ◽  
Walking To School ◽  
Elevated Exposure ◽  
Children’S Exposure

Children walking to school are at a high risk of exposure to air pollution compared with other modes because of the time they spend in close proximity to traffic during their commute. The aim of this study is to investigate the effect of a walker’s route choice on their exposure to ultrafine particles (UFP) on the walk to school. During morning commutes over a period of three weeks, exposure to UFP was measured along three routes: two routes were alongside both sides of a busy arterial road with significantly higher levels of traffic on one side compared to the other, and the third route passed through quiet streets (the background route). The results indicate that the mean exposure for the pedestrian walking along the background route was half the exposure experienced on the other two routes. Walkers on the trafficked side were exposed to elevated concentrations (>100,000 pt/cc) 2.5 times longer than the low-trafficked side. However, the duration of the elevated exposure for the background route was close to zero. Public health officials and urban planners may use the results of this study to promote healthier walking routes to schools, especially those planned as part of organized commutes.

PU composites based on different types of textile fibers

2021 ◽  
pp. 002199832110316
Author(s):  
Nuno Gama ◽  
B Godinho ◽  
Ana Barros-Timmons ◽  
Artur Ferreira
Keyword(s):  
Thermal Conductivity ◽  
Raw Materials ◽  
Natural Fibers ◽  
Tensile Modulus ◽  
High Water ◽  
Textile Fibers ◽  
Synthetic Fibers ◽  
Hydrophilic Nature ◽  
Different Types ◽  
Recycled Composites

In this study polyurethane (PU) residues were mixed with residues of textile fibers (cotton, wool and synthetic fibers up to 70 wt/wt) to produce 100% recycled composites. In addition, the effect of the type of fiber on the performance of the ensuing composites was evaluated. The presence of fibers showed similar effect on the density, reducing the density in the 5.5-9.0% range. In a similar manner, the addition of fillers decreased their thermal conductivity. The 70 wt/wt wool composite presented 38.1% lower thermal conductivity when compared to the neat matrix, a reduction that was similar for the other type of fibers. Moreover, the presence of fillers yields stiffer materials, especially in the case of the Wool based composites, which with 70 wt/wt of filler content increased the tensile modulus of the ensuing material 3.4 times. This was attributed to the aspect ratio and stiffness of this type of fiber. Finally, the high-water absorption and lower thermal stability observed, especially in the case of the natural fibers, was associated with the hydrophilic nature of fibers and porosity of composites. Overall, the results suggest that these textile-based composites are suitable for construction and automotive applications, with the advantage of being produced from 100% recycled raw-materials, without compromised performance.

Sign in / Sign up

Export Citation Format

Share Document