scholarly journals Design and implementation of 4 bit binary weighted current steering DAC

2020 ◽  
Vol 10 (6) ◽  
pp. 5642
Author(s):  
Jayeshkumar J. Patel ◽  
Amisha P. Naik
Keyword(s):  
Supply Voltage ◽  
Biomedical Application ◽  
Current Mode ◽  
Cmos Technology ◽  
Current Steering ◽  
Digital To Analog Converter ◽  
Transmission Gate ◽  
Linearity Error ◽  
Current Steering Dac ◽  
Binary Weighted

A compact current-mode Digital-to-Analog converter (DAC) suitable for biomedical application is repesented in this paper .The designed DAC is binary weighted in 180nm CMOS technology with 1.8V supply voltage. In this implementation, authors have focused on calculaton of Non linearity error say INL and DNL for 4 bit DAC having various type of switches: NMOS, PMOS and Transmission Gate. The implemented DAC uses lower area and power compared to unary architecture due to absence of digital decoders. The desired value of Integrated non linearity (INL) and Differential non linearity (DNL) for DAC for are within a range of +0.5LSB. Result obtained in this works for INL and DNL for the case DAC using Transmission Gate is +0.34LSB and +0.38 LSB respectively with 22mW power dissipation.

A 12-BIT 400-MS/s CURRENT-STEERING DAC WITH DEGLITCHING TECHNIQUE

2014 ◽  
Vol 23 (01) ◽  
pp. 1450004 ◽  
Author(s):  
XIAOBO XUE ◽  
XIAOLEI ZHU ◽  
QIFENG SHI ◽  
LENIAN HE
Keyword(s):  
Dynamic Range ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Signal Frequency ◽  
Current Steering ◽  
Digital To Analog Converter ◽  
Measurement Results ◽  
Voltage Swing ◽  
Current Steering Dac ◽  
Low Supply Voltage

In this paper, a 12-bit current-steering digital-to-analog converter (DAC) employing a deglitching technique is proposed. The deglitching technique is realized by lowering the voltage swing of the control signal as well as by using a method of glitch counteraction (GC). A new switch–driver structure is designed to enable the effectiveness of the GC and provide sufficient driving capability under a low supply voltage. Moreover, the control signal's rise/fall asymmetry which increases the glitch error can be suppressed by using the proposed switch–driver structure. The 12-bit DAC is implemented in 180 nm CMOS technology. The measurement results show that the spurious free dynamic range (SFDR) at low signal frequency is 78.8 dB, and it is higher than 70 dB up to 60 MHz signal frequency at 400 MS/s. The measured INL and DNL are both less than ±0.6 LSB.

scholarly journals An 8 bit current steering DAC for offset compensation purposes in sensor arrays

2012 ◽  
Vol 10 ◽  
pp. 201-206
Author(s):  
G. Bertotti ◽  
A. Laifi ◽  
E. Di Gioia ◽  
M. Masoumi ◽  
N. Dodel ◽  
...  
Keyword(s):  
Supply Voltage ◽  
Sensor Arrays ◽  
Cmos Technology ◽  
Digital Circuit ◽  
Current Steering ◽  
Worst Case ◽  
Current Output ◽  
Static Power ◽  
Offset Compensation ◽  
Current Steering Dac

Abstract. An 8 bit segmented current steering DAC is presented for the compensation of mismatch of sensors with current output arranged in a large arrays. The DAC is implemented in a 1.8 V supply voltage 180 nm standard CMOS technology. Post layout simulations reveal that the design target concerning a sampling frequency of 2.6 MHz is exceeded, worst-case settling time equals 60.6 ns. The output current range is 0–10 μA, which translates into an LSB of 40 nA. Good linearity is achieved, INL < 0.5 LSB and DNL < 0.4 LSB, respectively. Static power consumption with the outputs operated at a voltage of 0.9 V is approximately 10 μW. Dynamic power, mainly consumed by switching activity of the digital circuit parts, amounts to 100 μW at 2.6 MHz operation frequency. Total area is 38.6 × 2933.0 μm2.

scholarly journals 1.5-V CMOS Current Multiplier/Divider

2018 ◽  
Vol 8 (3) ◽  
pp. 1478 ◽  
Author(s):  
Jetsdaporn Satansup ◽  
Worapong Tangsrirat
Keyword(s):  
Low Voltage ◽  
Supply Voltage ◽  
Current Mode ◽  
Cmos Technology ◽  
Signal Frequency ◽  
Total Power ◽  
Total Power Consumption ◽  
Linearity Error ◽  
Low Supply Voltage ◽  
Circuit Technique

A circuit technique for designing a compact low-voltage current-mode multiplier/divider circuit in CMOS technology is presented.  It is based on the use of a compact current quadratic cell able to operate at low supply voltage.  The proposed circuit is designed and simulated for implementing in TSMC 0.25-m CMOS technology with a single supply voltage of 1.5 V.  Simulation results using PSPICE, accurately agreement with theoretical ones, have been provided, and also demonstrate a maximum linearity error of 1.5%, a THD less than 2% at 100 MHz, a total power consumption of 508 W, and -3dB small-signal frequency of about 245 MHz.

scholarly journals A Low Voltage High Speed Segmented Current Steering DAC for Neural Stimulation Application

2020 ◽  
Vol 8 (5) ◽  
pp. 4270-4274
Keyword(s):  
High Speed ◽  
Low Voltage ◽  
Supply Voltage ◽  
Neural Stimulation ◽  
Current Steering ◽  
Digital To Analog Converter ◽  
Analog Converter ◽  
Current Steering Dac ◽  
Disease And Disorders ◽  
Neural Stimulator

A multi-phasic neural stimulator using current steering Digital to Analog Converter with low resolution is in great demand to ameliorate symptoms of Parkinson's disease and disorders of consciousness. This article presents 5-bit segmented DAC designed for such applications. In order to simulate the design, cadence virtuoso tool with 180 nm MOS technology is used. The results obtained after simulation indicate that the proposed DAC offers +0.34 LSB INL and +0.36 LSB value for DNL. For the input of 200 MSPS, the power dissipation is about 22 mW when working with 1.8 V of supply voltage.

A 12-bit 200-MHz CURRENT-STEERING DAC WITH CALIBRATION

2014 ◽  
Vol 23 (04) ◽  
pp. 1450053 ◽  
Author(s):  
FAN XIA ◽  
YIQIANG ZHAO ◽  
GONGYUAN ZHAO
Keyword(s):  
Dynamic Range ◽  
Current Source ◽  
Cmos Technology ◽  
Signal Frequency ◽  
Current Steering ◽  
Digital To Analog Converter ◽  
Differential Nonlinearity ◽  
Spurious Free Dynamic Range ◽  
Source Block ◽  
Current Steering Dac

In this paper, a 12-bit current-steering digital-to-analog converter (DAC) with high static and dynamic linearity is proposed. Compared to traditional intrinsic-accuracy DACs, the static linearity is obtained by a series of subsidiary DACs which can shorten the calibration cycle with smaller additional circuits. The presented DAC is based on the segmented architecture and layout has been carefully designed so that better synchronization among the current sources can be achieved. The DAC is implemented in a standard 0.18-μm CMOS technology and the current source block occupies less than 0.5 mm2. The measured differential nonlinearity (DNL) and integral nonlinearity (INL) performance is ± 0.3 LSB and ± 0.5 LSB, respectively, and the spurious free dynamic range (SFDR) is 75 dB at 1 MHz signal frequency and 200 MHz sampling frequency.

scholarly journals Investigation of PVT-Aware STT-MRAM Sensing Circuits for Low-VDD Scenario

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 551
Author(s):  
Zhongjian Bian ◽  
Xiaofeng Hong ◽  
Yanan Guo ◽  
Lirida Naviner ◽  
Wei Ge ◽  
...  
Keyword(s):  
Nonvolatile Memory ◽  
High Speed ◽  
Low Voltage ◽  
Supply Voltage ◽  
Random Access ◽  
Magnetic Tunnel Junction ◽  
Complementary Metal Oxide Semiconductor ◽  
Current Mode ◽  
Cmos Technology ◽  
Oxide Semiconductor

Spintronic based embedded magnetic random access memory (eMRAM) is becoming a foundry validated solution for the next-generation nonvolatile memory applications. The hybrid complementary metal-oxide-semiconductor (CMOS)/magnetic tunnel junction (MTJ) integration has been selected as a proper candidate for energy harvesting, area-constraint and energy-efficiency Internet of Things (IoT) systems-on-chips. Multi-VDD (low supply voltage) techniques were adopted to minimize energy dissipation in MRAM, at the cost of reduced writing/sensing speed and margin. Meanwhile, yield can be severely affected due to variations in process parameters. In this work, we conduct a thorough analysis of MRAM sensing margin and yield. We propose a current-mode sensing amplifier (CSA) named 1D high-sensing 1D margin, high 1D speed and 1D stability (HMSS-SA) with reconfigured reference path and pre-charge transistor. Process-voltage-temperature (PVT) aware analysis is performed based on an MTJ compact model and an industrial 28 nm CMOS technology, explicitly considering low-voltage (0.7 V), low tunneling magnetoresistance (TMR) (50%) and high temperature (85 °C) scenario as the worst sensing case. A case study takes a brief look at sensing circuits, which is applied to in-memory bit-wise computing. Simulation results indicate that the proposed high-sensing margin, high speed and stability sensing-sensing amplifier (HMSS-SA) achieves remarkable performance up to 2.5 GHz sensing frequency. At 0.65 V supply voltage, it can achieve 1 GHz operation frequency with only 0.3% failure rate.

scholarly journals Design of area-efficient GHz range current mode frequency synthesizer using standard CMOS technology

2019 ◽  
Vol 70 (4) ◽  
pp. 323-328
Author(s):  
Dan-Dan Zheng ◽  
Yu-Bin Li ◽  
Chang-Qi Wang ◽  
Kai Huang ◽  
Xiao-Peng Yu
Keyword(s):  
Frequency Synthesizer ◽  
Frequency Tuning ◽  
Supply Voltage ◽  
Current Mode ◽  
Cmos Technology ◽  
Mode Frequency ◽  
Loop Filter ◽  
Silicon Area ◽  
Power Efficient ◽  
A Current

Abstract In this paper, an area and power efficient current mode frequency synthesizer for system-on-chip (SoC) is proposed. A current-mode transformer loop filter suitable for low supply voltage is implemented to remove the need of a large capacitor in the loop filter, and a current controlled oscillator with additional voltage based frequency tuning mechanism is designed with an active inductor. The proposed design is further integrated with a fully programmable frequency divider to maintain a good balance among output frequency operating range, power consumption as well as silicon area. A test chip is implemented in a standard 0.13 µm CMOS technology, measurement result demonstrates that the proposed design has a working range from 916 MHz to 1.1 l GHz and occupies a silicon area of 0.25 mm2 while consuming 8.4 mW from a 1.2 V supply.

A CMOS Automatic Gain Control Circuit for Biomedical Applications

2015 ◽  
Vol 645-646 ◽  
pp. 1308-1313
Author(s):  
Zhi Qiang Gao ◽  
Fu Xiang Huang ◽  
Jing Li ◽  
Liang Yin ◽  
Xiao Wei Liu
Keyword(s):  
Exponential Function ◽  
Biomedical Applications ◽  
Low Voltage ◽  
Supply Voltage ◽  
Automatic Gain Control ◽  
Gain Control ◽  
Cmos Technology ◽  
Chip Area ◽  
Gain Variation ◽  
Linearity Error

In this paper, a low-voltage automatic gain control (AGC) circuits is presented. The proposed circuit uses a novel approximated exponential function to increase the dB-linear output range. The three-stage AGC is fabricated in 0.18μm CMOS technology and shows the maximum gain variation of more than 100dB and a 67dB linear range with linearity error of less than ±1dB. The range of gain variation can be controlled from 34 to 101dB. The AGC dissipates less than 2.3mA under 1.8V supply voltage while occupying 0.4mm2 of chip area.

Sign in / Sign up

Export Citation Format

Share Document