Study of the heat transfer and analysis of the surface characteristics of robot spray painting by using Taguchi method and ANOVA analysis

2021 ◽  
pp. 095440892110676
Author(s):  
Raja Venkata Sai Kiran Jakkula ◽  
Prabhu Sethuramalingam
Keyword(s):  
Heat Transfer ◽  
Surface Finish ◽  
Research Work ◽  
Surface Characteristics ◽  
High Volume ◽  
Multiwall Carbon Nanotube ◽  
Paint Spray ◽  
Taguchi Design Of Experiments ◽  
Microscopy Analysis ◽  
Extended Surfaces

In this investigative research work, the surface characteristics of normal paint and multiwall carbon nanotube (MWCNT) paint-coated substrates are studied. The experiments are conducted using ABB IRB 1410 Robot and the end effector of the robot is retrofitted with a high-volume low-pressure atomizer paint spray gun. The nanopaint is prepared by ultrasonication by placing 1 gram of MWCNT in a polyurethane commercial base paint (500 ml). Taguchi design of experiments is used to identify the most efficient use of procedure parameters using the L9 orthogonal array table. Heat transfer of the substrate is found by temperature measurements of the convective heat transfer through extended surfaces. Surface morphology is studied by scanning electron microscope and upright microscopy. Analysis of variance technique is used to find the most influencing input parameters and contribution of values to maximizing surface finish and minimizing the heat transfer effect. The study shows that there is an enhancement in surface finish and minimization of heat transfer in the nanopaint coated substrate when compared with normal paint application using the ABB robot.

OSCILLATORY HEAT TRANSFER IN EXTENDED SURFACES

1990 ◽  
Author(s):  
J. M. Houghton ◽  
Derek B. Ingham ◽  
Peter J. Heggs
Keyword(s):  
Heat Transfer ◽  
Extended Surfaces

scholarly journals Approximate Analytical Analysis of Unsteady MHD Mixed Flow of Non-Newtonian Hybrid Nanofluid over a Stretching Surface

Fluids ◽  
2021 ◽  
Vol 6 (4) ◽  
pp. 138
Author(s):  
Ali Rehman ◽  
Zabidin Salleh
Keyword(s):  
Heat Transfer ◽  
Differential Equations ◽  
Base Fluid ◽  
Research Work ◽  
Hybrid Nanofluid ◽  
Stretching Surface ◽  
Optimal Homotopy Analysis Method ◽  
Analytical Analysis ◽  
Transfer Ratio ◽  
The Impact

This paper analyses the two-dimensional unsteady and incompressible flow of a non-Newtonian hybrid nanofluid over a stretching surface. The nanofluid formulated in the present study is TiO2 + Ag + blood, and TiO2 + blood, where in this combination TiO2 + blood is the base fluid and TiO2 + Ag + blood represents the hybrid nanofluid. The aim of the present research work is to improve the heat transfer ratio because the heat transfer ratio of the hybrid nanofluid is higher than that of the base fluid. The novelty of the recent work is the approximate analytical analysis of the magnetohydrodynamics mixed non-Newtonian hybrid nanofluid over a stretching surface. This type of combination, where TiO2+blood is the base fluid and TiO2 + Ag + blood is the hybrid nanofluid, is studied for the first time in the literature. The fundamental partial differential equations are transformed to a set of nonlinear ordinary differential equations with the guide of some appropriate similarity transformations. The analytical approximate method, namely the optimal homotopy analysis method (OHAM), is used for the approximate analytical solution. The convergence of the OHAM for particular problems is also discussed. The impact of the magnetic parameter, dynamic viscosity parameter, stretching surface parameter and Prandtl number is interpreted through graphs. The skin friction coefficient and Nusselt number are explained in table form. The present work is found to be in very good agreement with those published earlier.

Modeling and analysis of solar air channels with attachments of different shapes

2019 ◽  
Vol 29 (5) ◽  
pp. 1815-1845 ◽  
Author(s):  
Younes Menni ◽  
Ahmed Azzi ◽  
A. Chamkha
Keyword(s):  
Heat Transfer ◽  
Stokes Equations ◽  
Research Work ◽  
Convection Heat Transfer ◽  
Navier Stokes ◽  
Transfer Coefficients ◽  
Navier Stokes Equations ◽  
Content Type ◽  
Modeling And Analysis ◽  
Air Channels

Purpose This paper aims to report the results of numerical analysis of turbulent fluid flow and forced-convection heat transfer in solar air channels with baffle-type attachments of various shapes. The effect of reconfiguring baffle geometry on the local and average heat transfer coefficients and pressure drop measurements in the whole domain investigated at constant surface temperature condition along the top and bottom channels’ walls is studied by comparing 15 forms of the baffle, which are simple (flat rectangular), triangular, trapezoidal, cascaded rectangular-triangular, diamond, arc, corrugated, +, S, V, double V (or W), Z, T, G and epsilon (or e)-shaped, with the Reynolds number changing from 12,000 to 32,000. Design/methodology/approach The baffled channel flow model is controlled by the Reynolds-averaged Navier–Stokes equations, besides the k-epsilon (or k-e) turbulence model and the energy equation. The finite volume method, by means of commercial computational fluid dynamics software FLUENT is used in this research work. Findings Over the range investigated, the Z-shaped baffle gives a higher thermal enhancement factor than with simple, triangular, trapezoidal, cascaded rectangular-triangular, diamond, arc, corrugated, +, S, V, W, T, G and e-shaped baffles by about 3.569-20.809; 3.696-20.127; 3.916-20.498; 1.834-12.154; 1.758-12.107; 7.272-23.333; 6.509-22.965; 8.917-26.463; 8.257-23.759; 5.513-18.960; 8.331-27.016; 7.520-26.592; 6.452-24.324; and 0.637-17.139 per cent, respectively. Thus, the baffle of Z-geometry is considered as the best modern model of obstacles to significantly improve the dynamic and thermal performance of the turbulent airflow within the solar channel. Originality/value This analysis reports an interesting strategy to enhance thermal transfer in solar air channels by use of attachments with various shapes

scholarly journals Formations of Silicon Carbide and Epoxy Matrix Radiator: An Experimental Design, Dimension and Formulations

2019 ◽  
Vol 9 (1) ◽  
pp. 1793-1796
Keyword(s):  
Heat Transfer ◽  
Silicon Carbide ◽  
Experimental Design ◽  
Epoxy Resin ◽  
Epoxy Matrix ◽  
Research Work ◽  
Heat Transfer Analysis ◽  
The Given ◽  
Design Dimension

The greatest dealon the article have to approach the experimental design, dimensions and formulations in Silicon Carbide and Epoxy Matrix Radiator. The experiment prepared as per the fabrication chart behind that known about the characterization of material and proposal layout of fabrication work. Among the research work, concentrated the formation of silicon carbide epoxy matrix radiator in the given configuration and composition prepared as a high thermal conductive Epoxy resin is mixed at the ratio of 20wt% of epoxy resin 80% of Silicon Carbide. As silicon carbide has higher thermal conductivity and lowerthermal expansion than Aluminium and then the experimented result determined by the rate of heat transfer analysis such as the mode of heat transfer like Conduction, Convection and Radiation of the materials (Aluminium 6061 and Sic + Epoxy Resin). The following heat transfer characteristics formulated and calculated as per the given design, dimension and configuration of the materials.

scholarly journals Heat Transfer and Slip Effects on the Mhd Peristaltic Flow of Viscous Fluid in A Tapered Microvessels: Application of Blood Flow Research

2019 ◽  
Vol 9 (1) ◽  
pp. 5384-5390
Keyword(s):  
Heat Transfer ◽  
Blood Flow ◽  
Research Work ◽  
Flow Characteristics ◽  
Peristaltic Flow ◽  
Pressure Level ◽  
Slip Parameter ◽  
Electrically Conducting ◽  
Electrically Conducting Fluid ◽  
Slip Effects

This research work is proposed at reporting heat transfer on the peristaltic flow of an electrically conducting fluid in a tapered microvessels under the lubrication theory. The proposed geometry analyzes the blood flow in the heart vessels and maintain the pressure level in the human body. The solutions for the distribution of axial velocity, temperature distribution, pressure gradient and stream function have been obtained analytically. The influences of many evolving parameters on the flow characteristics are revealed and deliberated with the assist of figures. The mathematical outcomes show that the trapped bolus enhances in size with increasing slip parameter but decreases with the increase of Grashof number.

Immobilization of Radioactive Iodine Using AgI Vitrification Technique for the TRU Wastes Disposal: Evaluation of Leaching and Surface Properties

2008 ◽  
Vol 1107 ◽  
Author(s):  
Tomofumi Sakuragi ◽  
Tsutomu Nishimura ◽  
Yuji Nasu ◽  
Hidekazu Asano ◽  
Kuniyoshi Hoshino ◽  
...  
Keyword(s):  
Radioactive Iodine ◽  
Surface Condition ◽  
Pure Water ◽  
Surface Characteristics ◽  
High Volume ◽  
Reduction Efficiency ◽  
Iodine Release ◽  
Glass Surfaces ◽  
Release Model ◽  
Reprocessing Plant

AbstractIodine-129 collected from a reprocessing plant is regarded as the dominant nuclide in terms of safety for TRU wastes disposal in Japan. AgI vitrification (AgI-Ag2O-P2O5) is a potential iodine immobilization technique, which has the advantages of less iodine volatilization (low-temperature vitrification) and high volume reduction efficiency (approx. 1/25 the original waste volume). The iodine immobilization property can be evaluated by examining the surface condition of the AgI glass immersed in water. In this study, immersion tests have been performed on AgI glass in pure water in a 3% H2-N2 atmosphere at room temperature, and the surface characteristics have been examined. The thin layer (<4.3 μm) that is formed has been found to consist of AgI, which may act as a barrier, preventing leaching of glass components. The concepts behind the iodine release model have been proposed based on diffusion and the solubility of the components at the glass surfaces.

Effect of Draw Furnace Geometry on High Speed Optical Fiber Manufacturing

2000 ◽  
Author(s):  
Xu Cheng ◽  
Yogesh Jaluria
Keyword(s):  
Heat Transfer ◽  
Temperature Distribution ◽  
Optimal Design ◽  
Optical Fiber ◽  
High Speed ◽  
Graphite Furnace ◽  
Large Diameter ◽  
High Volume ◽  
Force Balance ◽  
Zonal Method

Abstract The motivation of manufacturers to pursue higher productivity and low costs in the fabrication of optical fibers requires large diameter silica-based preforms drawn into fiber at very high speed. An optimal design of the draw furnace is particularly desirable to meet the need of high-volume production in the optical fiber industry. This paper investigates optical fiber drawing at high draw speeds in a cylindrincal graphite furnace. A conjugate problem involving the glass and the purge gases is considered. The transport in the two regions is coupled through the boundary conditions at the free glass surface. The zonal method is used to model the radiative heat transfer in the glass. The neck-down profile of the preform at steady state is determined by a force balance, using an iterative numerical scheme. Thermally induced defects are also considered. To emphasize the effects of draw furnace geometry, the diameters of the preform and the fiber are kept fixed at 5 cm and 125 μm, respectively. The length and the diameter of the furnace are changed. For the purposes of comparison, a wide domain of draw speeds, ranging from 5 m/s to 20 m/s, is considered, and the form of the temperature distribution at the furnace surface is kept unchanged. The dependence of the preform/fiber characteristics, such as neckdown profile, velocity distribution and lag, temperature distribution and lag, heat transfer coefficent, defect concentration, and draw tension, on the furnace geometry is determined. Based on these numerical results, an optimal design of the draw furnace can be developed.

Investigation of Maximum Heat Transfer from an Aluminum Alloy Extended Surfaces

2017 ◽  
Vol 1 (2) ◽  
Author(s):  
Raad Muzahem Fenjan
Keyword(s):  
Heat Transfer ◽  
Aluminum Alloy ◽  
Maximum Heat ◽  
Maximum Heat Transfer ◽  
Extended Surfaces ◽  
Steady State Heat ◽  
Steady State Heat Transfer ◽  
Vertical Base ◽  
Fin Thickness ◽  
Fin Length

The aim of this research is to obtain the maximum steady state heat transfer used aluminum alloy extended surfaces which obtain the optimal design for these fins. For three cases, (according to both dimension and direction of the extended surfaces): vertical fins extended from horizontal base, vertical fins extended from vertical base , and horizontal fins extended from vertical base, the natural convective, conductive and radiative heat transfer was studied experimentally and respectively the comparison between these cases were achieved.  The parameters studied were distance between fins, fin length fin thickness and fin protrusion.

Sign in / Sign up

Export Citation Format

Share Document