scholarly journals Synthesis and mechanical behavior of composite material reinforced with Guadua fiber and with a polyurethane or polyester matrix

BioResources ◽  
2021 ◽  
Vol 16 (4) ◽  
pp. 8049-8059
Author(s):  
Ricardo Acosta ◽  
Gabriel Calle Trujillo ◽  
José Luddey Marulanda Arévalo
Keyword(s):  
Composite Material ◽  
Tensile Tests ◽  
Lower Percentage ◽  
Large Strains ◽  
Scanning Calorimetry ◽  
Hardness Tests ◽  
High Processing Speed ◽  
Polyester Matrix ◽  
Hot Melt ◽  
Polyurethane Matrix

A reactive hot-melt resin (polyurethane) was used to manufacture Guadua composites with a certain flexibility, high processing speed, good initial rigidity, and high temperature performance. These composites can support a moderate tensile stress, allow for large strains at low stresses, and have a low density and a working temperature range of -40 °C and 110 °C. During the flexural test, bamboo composites with reactive polyurethane matrix do not break or fail during the test. A polyurethane-based reactive hot-melt resin was characterized by tensile tests, Shore hardness tests, differential scanning calorimetry, and thermogravimetry. Besides, a composite material was made with Guadua fiber and polyester matrix, which had a greater strength in the test of tension and flexion, although it had a lower percentage of elongation than the composite material with reactive polyurethane. Guadua fiber can increase the strength by 266% of polyurethane matrix and 228% of polyester matrix.

Composite material with polyurethane-based reactive hot-melt matrix

2020 ◽  
pp. 002199832095080
Author(s):  
José Luddey Marulanda Arévalo ◽  
José Reyes Gasga ◽  
Miguel Ángel Martínez ◽  
Eligio Alberto Orozco Mendoza
Keyword(s):  
Contact Angles ◽  
Large Strains ◽  
Scanning Calorimetry ◽  
Temperature Range ◽  
Hardness Tests ◽  
High Processing Speed ◽  
The Matrix ◽  
Different Temperatures ◽  
Flexural Tests ◽  
Hot Melt

Reactive hot-melt resin can form joints with a certain flexibility, high processing speed, high initial rigidity, and high temperature. Such resins can be used to manufacture fiberglass composites because they support a high tensile stress, allow for large strains at low stresses, and have a low density and a working temperature range of −40–110°C. Furthermore, when the mechanical stress is removed, the material returns to its initial condition, as observed in the flexural tests. A polyurethane-based reactive hot-melt resin was characterized by tensile shear tests, Shore hardness tests, differential scanning calorimetry, and thermogravimetry. The contact angles at different temperatures were measured to evaluate the adhesive wettability and to select the best application temperature range of the adhesive, finding the best result at 140 °C. The matrix was characterized at different curing times, and matrix bonding with different adhesive materials was evaluated to provide a greater versatility of applications, to explore new fields of use of this resin as in the matrix of a composite with fiberglass.

scholarly journals Characterization a polyurethane-based reactive hot melt adhesive for applications in materials

DYNA ◽  
2019 ◽  
Vol 86 (210) ◽  
pp. 247-253
Author(s):  
JOSE LUDDEY MARULANDA AREVALO ◽  
Miguel Angel Martinez Casanova ◽  
JUANA ABEJONAR BUENDIA ◽  
ANTONIO PIQUERAS PEREZ
Keyword(s):  
Contact Angles ◽  
Tensile Shear ◽  
Shore Hardness ◽  
Shear Tests ◽  
Scanning Calorimetry ◽  
Hardness Tests ◽  
The Matrix ◽  
Melt Adhesives ◽  
High Processing ◽  
Hot Melt

In the present study, we used tensile shear tests, Shore hardness tests, differential scanning calorimetry (DSC), and thermogravimetry (TGA) to characterize a reactive polyurethane-based hot melt adhesive. We also measured contact angles at various temperatures to evaluate the wettability of the adhesive and to determine the optimum temperature range for applications. The adhesive was tested following curing for various times, and the bonding of the adhesive with several materials was investigated to determine whether it has the potential for greater versatility of application. Therefore, we explored new uses of the adhesive, such as in the matrix of a composite with fiberglass. Reactive hot melt adhesives are useful because they provide a certain degree of flexibility to joints, and have high processing speeds, high initial rigidity, and high working temperatures.

scholarly journals Effect of Cold Rolling on Cluster(1) Dissolvability during Artificial Aging and Formability during Natural Aging in Al-0.6Mg-1.0Si-0.5Cu Alloy

Metals ◽  
2022 ◽  
Vol 12 (1) ◽  
pp. 92
Author(s):  
Naoto Kirekawa ◽  
Kaisei Saito ◽  
Minho O ◽  
Equo Kobayashi
Keyword(s):  
Cold Rolling ◽  
Artificial Aging ◽  
Cluster Formation ◽  
Solution Treatment ◽  
Natural Aging ◽  
Tensile Tests ◽  
Scanning Calorimetry ◽  
Hardness Tests ◽  
Negative Effect ◽  
Cold Rolled

Natural aging after solution treatment has a negative effect on the precipitation strengthening of Al–Mg–Si alloys since Cluster(1) formed at a room temperature cannot be dissolved or transformed into precipitates during artificial aging at 170 °C. In this study, cold rolling is focused on as an alternative solution to pre-aging, which is a conventional method to prevent Cluster(1) formation. It is known that excess vacancies are necessary for cluster formation. Cold rolling suppresses cluster formation because excess vacancies disappear at dislocations introduced by cold rolling. In addition, it is expected that cold rolling accelerates the precipitation behavior because the diffusion of solute atoms is promoted by introduced lattice defects. The transition of Cluster(1) was evaluated by Micro Vickers hardness tests, tensile tests, electrical conductivity measurements and differential scanning calorimetry analyses. Results showed the negative effect of natural aging was almost suppressed in 10% cold-rolled samples and completely suppressed in 30% cold-rolled samples since Cluster(1) dissolved during artificial aging at 170 °C due to lowering of the temperature of Cluster(1) dissolution by cold rolling. It was found that the precipitation in cold-rolled samples was accelerated since the hardness peak of 10% cold-rolled samples appeared earlier than T6 and pre-aged samples.

scholarly journals Wastes from Agricultural Silage Film Recycling Line as a Potential Polymer Materials

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1383
Author(s):  
Jerzy Korol ◽  
Aleksander Hejna ◽  
Klaudiusz Wypiór ◽  
Krzysztof Mijalski ◽  
Ewelina Chmielnicka
Keyword(s):  
Vinyl Acetate ◽  
Thermal Performance ◽  
Mechanical Performance ◽  
Ethylene Vinyl Acetate ◽  
Tensile Tests ◽  
Solid Particles ◽  
Polymer Materials ◽  
Slight Reduction ◽  
Scanning Calorimetry ◽  
Crystallinity Degree

The recycling of plastics is currently one of the most significant industrial challenges. Due to the enormous amounts of plastic wastes generated by various industry branches, it is essential to look for potential methods for their utilization. In the presented work, we investigated the recycling potential of wastes originated from the agricultural films recycling line. Their structure and properties were analyzed, and they were modified with 2.5 wt % of commercially available compatibilizers. The mechanical and thermal performance of modified wastes were evaluated by tensile tests, thermogravimetric analysis, and differential scanning calorimetry. It was found that incorporation of such a small amount of modifiers may overcome the drawbacks caused by the presence of impurities. The incorporation of maleic anhydride-grafted compounds enhanced the tensile strength of wastes by 13–25%. The use of more ductile compatibilizers—ethylene-vinyl acetate and paraffin increased the elongation at break by 55–64%. The presence of compatibilizers also reduced the stiffness of materials resulting from the presence of solid particles. It was particularly emphasized for styrene-ethylene-butadiene-styrene and ethylene-vinyl acetate copolymers, which caused up to a 20% drop of Young’s modulus. Such effects may facilitate the further applications of analyzed wastes, e.g., in polymer film production. Thermal performance was only slightly affected by compatibilization. It caused a slight reduction in polyethylene melting temperatures (up to 2.8 °C) and crystallinity degree (up to 16%). For more contaminated materials, the addition of compatibilizers caused a minor reduction in the decomposition onset (up to 6 °C). At the same time, for the waste after three washing cycles, thermal stability was improved. Moreover, depending on the desired properties and application, materials do not have to go through the whole recycling line, simplifying the process, reducing energy and water consumption. The presented results indicate that it is possible to efficiently use the materials, which do not have to undergo the whole recycling process. Despite the presence of impurities, they could be applied in the manufacturing of products which do not require exceptional mechanical performance.

scholarly journals Characterization of Beeswax, Candelilla Wax and Paraffin Wax for Coating Cheeses

Coatings ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 261
Author(s):  
Adolfo Bucio ◽  
Rosario Moreno-Tovar ◽  
Lauro Bucio ◽  
Jessica Espinosa-Dávila ◽  
Francisco Anguebes-Franceschi
Keyword(s):  
Physical And Mechanical Properties ◽  
Tensile Tests ◽  
Paraffin Wax ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Absorption Bands ◽  
Dimensional Changes ◽  
Ductile Behavior ◽  
Candelilla Wax

A study on the physical and mechanical properties of beeswax (BW), candelilla wax (CW), paraffin wax (PW) and blends was carried out with the aim to evaluate their usefulness as coatings for cheeses. Waxes were analyzed by X-ray diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), differential scanning calorimetry (DSC), permeability, viscosity, flexural and tensile tests and scanning electron microscopy. Cheeses were coated with the waxes and stored for 5 weeks at 30 °C. Measured parameters were weight, moisture, occurrence and degree of fractures, and dimensional changes. The crystal phases identified by XRD for the three waxes allowed them to determine the length of alkanes and the nonlinear compounds in crystallizable forms in waxes. FTIR spectra showed absorption bands between 1800 and 800 cm−1 related to carbonyls in BW and CW. In DSC, the onset of melting temperature was 45.5 °C for BW, and >54 °C for CW and PW. Cheeses coated with BW did not show cracks after storage. Cheeses coated with CW and PW showed microcraks, and lost weight, moisture and shrunk. In the flexural and tensile tests, BW was ductile; CW and PW were brittle. BW blends with CW or PW displays a semi ductile behavior. Cheeses coated with BW blends lost less than 5% weight during storage. The best waxes were BW and the blends.

scholarly journals Metallization of Thermoplastic Polymers and Composites 3D Printed by Fused Filament Fabrication

Technologies ◽  
2021 ◽  
Vol 9 (3) ◽  
pp. 49
Author(s):  
Alessia Romani ◽  
Andrea Mantelli ◽  
Paolo Tralli ◽  
Stefano Turri ◽  
Marinella Levi ◽  
...  
Keyword(s):  
Physical Vapor Deposition ◽  
Test Sample ◽  
Tensile Tests ◽  
Layer By Layer ◽  
Post Processing ◽  
Thermoplastic Polymers ◽  
Fused Filament Fabrication ◽  
Scanning Calorimetry ◽  
3D Printed ◽  
Manufacturing Technologies

Fused filament fabrication allows the direct manufacturing of customized and complex products although the layer-by-layer appearance of this process strongly affects the surface quality of the final parts. In recent years, an increasing number of post-processing treatments has been developed for the most used materials. Contrarily to other additive manufacturing technologies, metallization is not a common surface treatment for this process despite the increasing range of high-performing 3D printable materials. The objective of this work is to explore the use of physical vapor deposition sputtering for the chromium metallization of thermoplastic polymers and composites obtained by fused filament fabrication. The thermal and mechanical properties of five materials were firstly evaluated by means of differential scanning calorimetry and tensile tests. Meanwhile, a specific finishing torture test sample was designed and 3D printed to perform the metallization process and evaluate the finishing on different geometrical features. Furthermore, the roughness of the samples was measured before and after the metallization, and a cost analysis was performed to assess the cost-efficiency. To sum up, the metallization of five samples made with different materials was successfully achieved. Although some 3D printing defects worsened after the post-processing treatment, good homogeneity on the finest details was reached. These promising results may encourage further experimentations as well as the development of new applications, i.e., for the automotive and furniture fields.

scholarly journals Mechanical, Thermal and Rheological Properties of Polyethylene-Based Composites Filled with Micrometric Aluminum Powder

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1242
Author(s):  
Olga Mysiukiewicz ◽  
Paulina Kosmela ◽  
Mateusz Barczewski ◽  
Aleksander Hejna
Keyword(s):  
Mechanical Properties ◽  
Melt Flow Index ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Flow Index ◽  
Scanning Calorimetry ◽  
Metal Composites ◽  
Pre Treatment ◽  
The Impact ◽  
Properties Of Composites

Investigations related to polymer/metal composites are often limited to the analysis of the electrical and thermal conductivity of the materials. The presented study aims to analyze the impact of aluminum (Al) filler content (from 1 to 20 wt%) on the rarely investigated properties of composites based on the high-density polyethylene (HDPE) matrix. The crystalline structure, rheological (melt flow index and oscillatory rheometry), thermal (differential scanning calorimetry), as well as static (tensile tests, hardness, rebound resilience) and dynamic (dynamical mechanical analysis) mechanical properties of composites were investigated. The incorporation of 1 and 2 wt% of aluminum filler resulted in small enhancements of mechanical properties, while loadings of 5 and 10 wt% provided materials with a similar performance to neat HDPE. Such results were supported by the lack of disturbances in the rheological behavior of composites. The presented results indicate that a significant content of aluminum filler may be introduced into the HDPE matrix without additional pre-treatment and does not cause the deterioration of composites’ performance, which should be considered beneficial when engineering PE/metal composites.

Using Embossing to Create a Fiber Reinforced Honeycomb Composite

2005 ◽  
Vol 127 (2) ◽  
pp. 257-262 ◽  
Author(s):  
William Jordan
Keyword(s):  
Tensile Strength ◽  
Composite Material ◽  
Carbon Fibers ◽  
Flexural Modulus ◽  
Testing Machine ◽  
Charpy Impact ◽  
Tensile Tests ◽  
Hydraulic Testing ◽  
Charpy Impact Toughness ◽  
Bend Tests

This research project used hot embossing to create a strong and tough polymeric based composite structure. A honeycomb type structure was created by pressing small grooves into thin polycarbonate sheets. A trapezoidal die was used to create hexagonal shaped channels in the polymeric sheet. A number of these sheets were then bonded together to form a composite material. Carbon fibers were embedded into the channels in some of the laminates. The embossing process was carried out at an elevated temperature in an environmental chamber attached to an MTS servo hydraulic testing machine. The grooved structure had a 31% to 45% decrease in the apparent density compared to the ungrooved specimens. Bend tests, tensile tests, and Charpy impact tests were performed on laminates made from this material. The specific values of tensile strength, flexural modulus, and Charpy impact toughness were increased. A small percentage of fibers significantly increased both the stiffness and strength of the laminate.

Sign in / Sign up

Export Citation Format

Share Document