Dynamic performance improvement of wind farms equipped with three SCIG generators using STATCOM

2014 ◽  
Vol 25 (4) ◽  
pp. 128-135 ◽  
Author(s):  
Othman Hasnaoui ◽  
Mehdi Allagui
Keyword(s):  
Power Flow ◽  
Wind Farm ◽  
Transient Stability ◽  
Reactive Power ◽  
Dynamic Performance ◽  
Wind Farms ◽  
System Stability ◽  
Static Synchronous Compensator ◽  
Power Flow Control ◽  
Ac Transmission

The main causes of wind farms disconnection from the grid is the three-phase grid faults at the point common coupling (PCC) e.g. the voltage dip. The use of a Static Synchronous Compensator (STATCOM) which is from the family of Flexible AC Transmission System (FACTS) devices can be used effectively in a wind park based on FSIG to provide transient voltage and to improve wind system stability. Due to the asynchronous operation nature, system instability of wind farms based on FSIG (Fixed Speed Induction Generator) is largely caused by the reactive power absorption by FSIG because due to the large rotor slip during grid fault. STATCOM contributes to control the grid voltage at PCC and maintain wind farm connection to the grid during some severe conditions of grid faults and used for power flow control and for damping power system oscillations. The evaluation of this control strategy using (STATCOM) is investigated in terms of regulation reactive power and transient stability of the wind farm during grid disturbances.

Study of Voltage Stability in Grid-Connected Large Wind Farms

2012 ◽  
Vol 433-440 ◽  
pp. 1794-1801 ◽  
Author(s):  
Jian Dong Duan ◽  
Rui Li ◽  
Lin An
Keyword(s):  
Power Systems ◽  
Power System ◽  
Voltage Stability ◽  
Wind Farm ◽  
Reactive Power ◽  
Dynamic Performance ◽  
Wind Farms ◽  
System Stability ◽  
Induction Generator ◽  
Large Wind

Squirrel-cage induction generator (SCIG), as its structural and economic advantages, has been widely utilized in large wind farms in China. However, the large wind farm composed of induction generators will cause obvious problems to the power system stability due to the dependency on reactive power. At the same time, Doubly-fed induction generator (DFIG), as a new type of wind turbine generator, has excellent dynamic characteristics for operation of wind farms. With the increase in penetration of wind power in power systems, more and more wind farms will use both SCIG and DFIG. In this case, the dynamic characteristic of wind farm on power systems is becoming an important issue especially in terms of the voltage stability. This article is to show by means of simulations the dynamic performance of wind farm linked to power system under the circumstances of network disturbances. Furthermore, the interaction between the SCIGs and DFIGs has also been investigated. A detailed model of wind farms is presented through the plat root of MATLAB/SIMULINK. The simulation results demonstrate that the DFIG applications will largely improve the dynamic performance of wind farm in certain conditions, if the DFIGs could be applied reasonably, the voltage stability of the wind farm will be largely improved and even low voltage ride through(LVRT) characteristic of SCIGs, which may be a good solution to reduce the high dependence of costly reactive power compensation equipment(Some flexible AC transmission systems devices like SVC, STATCOM) to some extent.

Effect of unified power flow controller installation in dual feed induction generator (DFIG) wind turbines

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Asaad Shemshadi ◽  
Pourya Khorampour
Keyword(s):  
Power Flow ◽  
Wind Farm ◽  
Reactive Power ◽  
Wind Farms ◽  
Transient Behavior ◽  
Unified Power Flow Controller ◽  
Voltage Fluctuations ◽  
Flow Controller ◽  
Power Flow Controller ◽  
Sudden Load

Abstract In recent years, the use of wind energy to generate electricity in the world has been accelerating and growing. Wind farms are unstable when dynamic voltage fluctuations occur, especially sudden and sudden changes in load, and show oscillating performance at their output. In this paper, the Unified Power Flow Controller (UPFC) has been simulated and studied by Matlab software to improve the dynamic stability and transient behavior of the wind power plant in the event of sudden load changes. The simulation results show that by controlling the UPFC series inverter, voltage fluctuations in the PCC bus are prevented and the UPFC parallel inverter injects power after changing the load for faster recovery and stability of the PCC bus voltage and thus the stability of the wind farm. The UPFC can control the active and reactive power at the transmission line, and in fact, controls the output of the wind turbine with the generator from both sides to the fluctuations caused by sudden load changes that play a role such as sudden disturbances and oscillating errors. Also, the presence of UPFC in the system reduces power fluctuations.

Improving Active Output Capacity of Large-Scale Wind Farm by Installation STATCOM

2012 ◽  
Vol 588-589 ◽  
pp. 574-577 ◽  
Author(s):  
Yan Juan Wu ◽  
Lin Chuan Li
Keyword(s):  
Control Strategy ◽  
Large Scale ◽  
Wind Farm ◽  
Transient Stability ◽  
Reactive Power ◽  
Feedforward Control ◽  
Wind Farms ◽  
Active Power ◽  
Utilization Efficiency ◽  
Grid Voltage

Some faults will result wind turbine generators off-grid due to low grid voltage , furthermore, large-scale wind farms tripping can result in severe system oscillation and aggravate system transient instability . In view of this, static compensator (STATCOM) is installed in the grid containing large-scale wind farm. A voltage feedforward control strategy is proposed to adjust the reactive power of STATCOM compensation and ensure that the grid voltage is quickly restored to a safe range. The mathematical model of the doubly-fed induction wind generator (DFIG) is proposed. The control strategy of DFIG uses PI control for rotor angular velocity and active power. 4-machine system simulation results show that the STATCOM reactive power compensation significantly improve output active power of large-scale wind farm satisfying transient stability, reduce the probability of the tripping, and improve the utilization efficiency of wind farms.

Research on Effects of STATCOM on Voltage in Wind Farm Based on PSASP

2013 ◽  
Vol 433-435 ◽  
pp. 1320-1324
Author(s):  
Wei Zheng ◽  
Shi Qun Li ◽  
Yong Zhi ◽  
Run Qing Bai ◽  
Chen Liang ◽  
...  
Keyword(s):  
Power System ◽  
Power Flow ◽  
Wind Farm ◽  
Transient Stability ◽  
System Analysis ◽  
Transient State ◽  
Gansu Province ◽  
Static Synchronous Compensator ◽  
Stability Calculation ◽  
Power Base

Recently, the static synchronous compensator (STATCOM) device has been installed in Jiuquan wind farm in Gansu Province. To study its ability to support voltage, this paper presents a study of the mathematical model of the steady state and transient state of STATCOM and then uses the power system analysis software package (PSASP) to establish a user-defined model of STATCOM. In addition, the model is added into the power system example (CEPRI 7). After that, the power flow calculation and transient stability calculation are carried out to simulate and analyze. At last the STATCOM device is field tested in Jiuquan wind power base. Test results verify that STATCOM effectively supports the grid voltage.

scholarly journals Transient Stability Enhancement of Multimachine Power System Using Robust and Novel Controller Based CSC-STATCOM

2015 ◽  
Vol 2015 ◽  
pp. 1-12 ◽  
Author(s):  
Sandeep Gupta ◽  
Ramesh Kumar Tripathi
Keyword(s):  
Power System ◽  
Transient Stability ◽  
Reactive Power ◽  
Controller Design ◽  
Current Source ◽  
Test System ◽  
Vital Role ◽  
Static Synchronous Compensator ◽  
Ac Transmission ◽  
The Impact

A current source converter (CSC) based static synchronous compensator (STATCOM) is a shunt flexible AC transmission system (FACTS) device, which has a vital role as a stability support for small and large transient instability in an interconnected power network. This paper investigates the impact of a novel and robust pole-shifting controller for CSC-STATCOM to improve the transient stability of the multimachine power system. The proposed algorithm utilizes CSC based STATCOM to supply reactive power to the test system to maintain the transient stability in the event of severe contingency. Firstly, modeling and pole-shifting controller design for CSC based STATCOM are stated. After that, we show the impact of the proposed method in the multimachine power system with different disturbances. Here, applicability of the proposed scheme is demonstrated through simulation in MATLAB and the simulation results show an improvement in the transient stability of multimachine power system with CSC-STATCOM. Also clearly shown, the robustness and effectiveness of CSC-STATCOM are better rather than other shunt FACTS devices (SVC and VSC-STATCOM) by comparing the results in this paper.

A Control Strategy for Transient Stability Improvement of Doubly-Fed Wind Power Generation System

2014 ◽  
Vol 953-954 ◽  
pp. 337-341
Author(s):  
Chao Xu ◽  
Jin Ling Lu ◽  
Jin Long Zhou
Keyword(s):  
Control Strategy ◽  
Wind Farm ◽  
Transient Stability ◽  
Reactive Power ◽  
System Stability ◽  
Control Loop ◽  
Reactive Control ◽  
Voltage Control Strategy ◽  
Transient Voltage ◽  
Doubly Fed

A novel inverter control strategy to enhance the transient stability of grid-connected wind farm based on doubly-fed induction generator (DFIG) is presented. Adding transient angle control strategy in the rotor side converter active control loop, this can dissipate the system unbalancing energy and restrain the system oscillations by the variation of wind turbine speed. Adding transient voltage control strategy in reactive control loop, this can provide fast reactive power compensation and support the restoration and reconstruction of the grid voltage when fault occurred. The control strategy which can improve the transient Angle stability and transient voltage stability at the same time is put forward. Finally, a testing system including a DFIG-based wind farm is realized using DigSILENT/Power Factory, the strategy validation and the contribution to power system stability enhancement are verified by simulation.

Using Dynamic Reactive Power Compensation Equipments to Enhance Low Voltage Ride-Through Capability of Fixed Speed Asynchronous Wind Farms

2013 ◽  
Vol 291-294 ◽  
pp. 481-489 ◽  
Author(s):  
Yu Lin Hu ◽  
Lei Shi ◽  
Hao Ming Liu
Keyword(s):  
Wind Farm ◽  
Reactive Power ◽  
Low Voltage ◽  
Wind Farms ◽  
Reactive Power Compensation ◽  
Mass Model ◽  
Static Synchronous Compensator ◽  
Conversion Model ◽  
Low Voltage Ride Through ◽  
Wind Generators

This paper presents wind energy conversion model, drive shaft’s dual-mass model and generator’s transient mathematical model for the transient analysis of fixed speed asynchronous wind generators, and analyzes the transient characteristics of the wind generators under the condition of low voltage fault. The control principles of two dynamic reactive power compensation equipments as static var compensator (SVC) and static synchronous compensator (STATCOM) are introduced. Take a wind farm consists of fixed speed asynchronous wind generators as an example, the two compensation equipments are simulated in PowerFactory/DIgSILENT to compare the effort of them on enhancing the low voltage ride-through capability of the wind farm.

scholarly journals Modelling of Transformerless Upfc Toimprovepower System Stability using Optimization Technique

2019 ◽  
Vol 8 (4) ◽  
pp. 11456-11459
Keyword(s):  
Power Flow ◽  
Reactive Power ◽  
Optimization Technique ◽  
System Stability ◽  
Unified Power Flow Controller ◽  
Flexible Ac Transmission ◽  
Flexible Ac Transmission System ◽  
Facts Devices ◽  
Ac Transmission ◽  
Power Flow Controller

Generally, power system faces the problem to transfer power from one system to another system without any fluctuations, with minimal of system losses. To overcome this problems, a flexible ac transmission system is implemented in this paper. In present scenario, facts devices are used to reduce the transmission losses for improvising transmission capacity and also to improve the system capability. Unified Power Flow Controller plays a most prominent role in FACTS controller to improve the system stability. The structure of UPFC is combination of back-back converters with boosting and zigzag transformer. This type of UPFC system consists of high losses due to presence of magnetic properties in this transformer. With this, a transformer-less multilevel inverter based UPFC topology is proposed in this paper. This paper focuses on the modulation of transformerless UPFC with PSO, which controlsfundamental frequency for better controlling of active and reactive power, harmonic minimization, and improvement in efficiency of system by controlling DC link voltage

Modelling of TCSC Controller for Transient Stability Enhancement

2006 ◽  
Vol 7 (1) ◽  
Author(s):  
Ramnarayan Patel ◽  
Vasundhara Mahajan ◽  
Vinay Pant
Keyword(s):  
Power System ◽  
Power Flow ◽  
Transient Stability ◽  
Electrical Power ◽  
Fast Response ◽  
Transmission System ◽  
System Stability ◽  
Electrical Power System ◽  
Facts Controllers ◽  
Ac Transmission

Power engineers are currently facing challenges to increase the power transfer capabilities of existing transmission system. Flexible AC Transmission system (FACTS) controllers can balance the power flow and thereby use the existing power system network most efficiently. Because of their fast response, FACTS controllers can also improve the stability of an electrical power system by helping critically disturbed generators to give away the excess energy gained through the acceleration during fault. Thyristor controlled series compensator (TCSC) is an important device in FACTS family, and is widely recognized as an effective and economical means to solve the power system stability problem. TCSC is used as series compensator in transmission system. In the present work a TCSC controller is designed and tested over a single machine infinite bus (SMIB) as well as a multi-machine power system. Detailed simulation studies are carried out with MATLAB/SIMULINK environment and the effect of the TCSC parameter variations over the system stability is studied.

Study of Reactive Power Compensation for Improvement of Low-Voltage-Ride-Through Capability of Wind Farm

2013 ◽  
Vol 724-725 ◽  
pp. 619-622 ◽  
Author(s):  
Chia Yu Hsu ◽  
Ta Hsiu Tseng ◽  
Pei Hwa Huang
Keyword(s):  
Wind Farm ◽  
Reactive Power ◽  
Low Voltage ◽  
Wind Farms ◽  
Static Synchronous Compensator ◽  
Low Voltage Ride Through ◽  
Induction Generators ◽  
Turbine Generators ◽  
Set Up ◽  
Doubly Fed

The main purpose of this paper is to study the enhancement of the Low-Voltage-Ride-Through (LVRT) capability of the wind farm with the installment of the Static Synchronous Compensator (STATCOM) and the Static Var Compensator (SVC). With more penetration of wind energy from on-shore and off-shore wind farms, utilities have been starting to set up the regulation requiring the wind turbine generators to remain connected to the grid when a fault takes place in the system which is referred to as Low-Voltage-Ride-Through (LVRT). A wind farm composed with doubly fed induction generators is used as the study system. Both the STATCOM and the SVC are utilized as the devices for enhancing the LVRT capability of the wind farm. The results are demonstrated for comparing the performance of the two devices in the improvement of voltage dynamic characteristics of the study system.

Sign in / Sign up

Export Citation Format

Share Document