scholarly journals Spray Characteristics at Preheating Temperatur of Diesel-Biodiesel-Gasoline Fuel Blend

2021 ◽  
Vol 5 (2) ◽  
pp. 134
Author(s):  
Moch Miftahul Arifin ◽  
Nasrul Ilminnafik ◽  
Muh. Nurkoyim Kustanto ◽  
Agus Triono
Keyword(s):  
Diesel Engines ◽  
High Speed ◽  
Fuel Injection ◽  
Fuel Mixture ◽  
Spray Angle ◽  
Injection System ◽  
Spray Characteristics ◽  
Fuel Blend ◽  
Spray Tip Penetration

Technological developments in diesel engines require improvements to the fuel injection system to meet the criteria for economical, high-power and efficient combustion and meet environmental regulatory standards. One method that has a lot of interest is changing the characteristics of the fuel, with the aim of producing optimal combustion. Spray characteristics have a big role in determining the quality of combustion in diesel engines. A good spray can improve the quality of fuel atomization and the homogeneity of the air-fuel mixture in the combustion chamber so that it can produce good engine performance and low emissions. This study aims to determine the effect of a diesel-biodiesel (Calophyllum inophyllum)-gasoline blendandfuel heating on the spray characteristics. The research was conducted with variations in composition (B0, B100, B30, B30G5 and B30G10) and fuel heating (40, 60, 80, and 100 °C). Fuel injected atapressure of 17 MPa in to a pressure chamber of 3 bar. The spray formed was recorded with a high-speed camera of 480 fps (resolution 224x168 pixel). In B100 biodiesel, the highest viscosity and density cause high spray tip penetration, small spray angle, and high spray velocity. The addition of diesel oil, gasoline, and heating fuel reduces the viscosity and density so that the spray tip penetration decreases, the spray angle increases and the velocity of spray decreases.

Scaling liquid penetration in evaporating sprays for different size diesel engines

2019 ◽  
Vol 21 (9) ◽  
pp. 1662-1677 ◽  
Author(s):  
Xinyi Zhou ◽  
Tie Li ◽  
Yijie Wei ◽  
Ning Wang
Keyword(s):  
Diesel Engine ◽  
Diesel Engines ◽  
High Speed ◽  
Scaling Laws ◽  
Fuel Injection ◽  
Pollutant Emissions ◽  
Liquid Penetration ◽  
Spray Characteristics ◽  
Penetration Length ◽  
Air Mixing

Scaled model experiments can greatly reduce the cost, time and energy consumption in diesel engine development, and the similarity of spray characteristics has a primary effect on the overall scaling results of engine performance and pollutant emissions. However, although so far the similarity of spray characteristics under the non-evaporating condition has been studied to some extent, researches on scaling the evaporating sprays are still absent. The maximum liquid penetration length has a close relationship with the spray evaporation processes and is a key parameter in the design of diesel engine spray combustion system. In this article, the similarity of maximum liquid penetration length is theoretically derived based on the hypotheses that the spray evaporation processes in modern high-pressure common rail diesel engines are fuel–air mixing controlled and local interphase transport controlled, respectively. After verifying that the fuel injection rates are perfectly scaled, the similarity of maximum liquid penetration length in evaporating sprays is studied for three scaling laws using two nozzles with hole diameter of 0.11 and 0.14 mm through the high-speed diffused back-illumination method. Under the test conditions of different fuel injection pressures, ambient temperatures and densities, the lift-off law and speed law lead to a slightly increased maximum liquid penetration length, while the pressure law can well scale the maximum liquid penetration length. The experimental results are consistent with the theoretical analyses based on the hypothesis that the spray evaporation processes are fuel–air mixing controlled, indicating that the local interphase transports of energy, momentum and mass on droplet surface are not rate-controlled steps with respect to spray evaporation processes.

Direct Water Injection to Improve Diesel Spray Combustion

2003 ◽  
Author(s):  
Koji Takasaki ◽  
Tatsuo Takaishi ◽  
Hiroyuki Ishida ◽  
Keijirou Tayama
Keyword(s):  
Diesel Engines ◽  
High Speed ◽  
Fuel Injection ◽  
Nox Reduction ◽  
Water Injection ◽  
Injection Pressure ◽  
Injection System ◽  
Injection Hole ◽  
Low Speed ◽  
Direct Water Injection

Now, it is essential to apply some measures for NOx reduction to low-speed diesel engines emitting much more NOx than high-speed engines. At the same time PM emission must be reduced especially when bunker fuel or heavy fuel is burned. This paper describes the applications of SFWI (Stratified Fuel Water Injection) system and DWI (Direct Water Injection) system to large sized diesel engines to reduce NOx and PM emission. SFWI system makes it possible to inject water during fuel injection from the same nozzle hole without mixing the liquids. DWI system injects water with high injection pressure from the other injection hole than the fuel injection hole into the combustion chamber directly. For testing both the systems, a 2-stroke-cycle low-speed test engine was used.

Application of HFRT Methods to Diagnose the Technical Condition of High-Speed Marine Diesel Engines

2015 ◽  
Vol 236 ◽  
pp. 161-168
Author(s):  
Tomasz Lus
Keyword(s):  
Diesel Engines ◽  
High Speed ◽  
Internal Combustion Engines ◽  
Fuel Injection ◽  
Combustion Process ◽  
Technical Condition ◽  
Injection System ◽  
Engine Fuel ◽  
Naval Academy ◽  
Marine Diesel

The paper presents problems related to testing of the technical condition of high-speed marine diesel engines that are not equipped with indicated valves, as it is in the case of larger medium-and low-speed marine internal combustion engines. In this case, in assessment of technical condition of engine fuel injection system and valve gear system a vibration signals (in time / angle domain) analysis modified method called HFRT (High Frequency Resonance Technique) can be used. This method indirectly helps also to evaluate the fuel combustion process in the engine cylinders. The paper presents the theoretical basis of a modified HFRT method, physical implementation of the marine diesel engine system’s analyzer used for marine engines testing built at the Institute of Construction and Operation of Ships at Polish Naval Academy (PNA) in Gdynia. The paper also includes a description of the vibration signal processing methodology and examples of measurements made in the ships conditions for a few selected types of engines.

scholarly journals Characteristics of pressure wave in common rail fuel injection system of high-speed direct injection diesel engines

2016 ◽  
Vol 8 (5) ◽  
pp. 168781401664824 ◽  
Author(s):  
Mohammad Reza Herfatmanesh ◽  
Zhijun Peng ◽  
Alexis Ihracska ◽  
Yuzhen Lin ◽  
Lipeng Lu ◽  
...  
Keyword(s):  
Diesel Engines ◽  
Pressure Wave ◽  
High Speed ◽  
Fuel Injection ◽  
Direct Injection ◽  
Common Rail ◽  
Injection System ◽  
Fuel Injection System

Analysis of Fuel Injection Parameter on Biodiesel and Diesel Spray Characteristics Using Common Rail System

2014 ◽  
Vol 974 ◽  
pp. 362-366 ◽  
Author(s):  
Amir Khalid ◽  
Azwan Sapit ◽  
M.N. Anuar ◽  
Him Ramsy ◽  
Bukhari Manshoor ◽  
...  
Keyword(s):  
Fuel Injection ◽  
Injection Pressure ◽  
Common Rail ◽  
Spray Angle ◽  
Injection System ◽  
Injection Timing ◽  
Ignition Process ◽  
Mixture Formation ◽  
Spray Characteristics ◽  
Penetration Length

Precise control of fuel injection is essential in modern diesel engines especially in controlling the precise injection quantity, flexible injection timing, flexible rate of injection with multiple injections and high injection pressures. It was known that the fuel-air mixing is mainly influenced by the fuel injection system and injector nozzle characteristics. Thus, mixture formation during ignition process associated with the exhaust emissions. The purpose of this study is to investigate the influence of spray characteristics on the mixture formation. In this study, common rail injector systems with different model of injector were used to simulate the actual mixture formation inside the engine chamber. The optical visualization system was constructed with a digital video camera in order to investigate the detailed behavior of mixture formation. This method can capture spray penetration length, spray angle, spray evaporation and mixture formation process clearly. The spray characteristic such as the penetration length, spray angle and spray area are increasing when the injection pressure increased. The mixture formation can be improved effectively by increasing the injection pressure.

scholarly journals Comprehensive Spray Characteristics of Water in Port Fuel Injection Injector

Energies ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 396 ◽  
Author(s):  
Park ◽  
Lee ◽  
Park
Keyword(s):  
Fuel Injection ◽  
Injection Pressure ◽  
High Viscosity ◽  
Spray Angle ◽  
Spray Characteristics ◽  
Spray Tip Penetration ◽  
Port Fuel Injection ◽  
Injection Quantity ◽  
Spray Droplets ◽  
Spray Visualization

The objective of this study was to compare the injection and spray characteristics of water with n-heptane using a port fuel injection (PFI) system. In this study, the injection pressure was changed to 0.3–0.9 Mpa and the energizing duration was changed to 0.5–4 ms. To investigate spray characteristics, the injection quantities of n-heptane and water were measured. Macroscopic spray characteristics were determined through spray visualization. The Sauter mean diameter (SMD) and velocity of spray droplets were measured with a phase Doppler anemometry (PDA) experiment. Spray tip penetration, spray angle, SMD of droplets, and spray droplet velocity were compared. As the injection pressure increased, the injection quantity and the droplets velocity increased. However, the spray tip penetration, SMD of the droplet, and the spray angle decreased. The increase in energizing duration led to an increase in the injection quantity without affecting other spray characteristics. The higher density of water also increased injection quantity, resulting in a decrease in spray tip penetration and increases of SMD and velocity of spray droplets due to high viscosity and surface tension of water.

A Phenomenological Model for Combustion and Emissions in Small Bore, High Speed, Direct Injection Diesel Engines

2005 ◽  
Author(s):  
N. A. Henein ◽  
I. P. Singh ◽  
L. Zhong ◽  
Y. Poonawala ◽  
J. Singh ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Engines ◽  
Phenomenological Model ◽  
High Speed ◽  
Gas Flow ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Injection Process ◽  
Wide Range

This paper introduces a phenomenological model for the fuel distribution, combustion, and emissions formation in the small bore, high speed direct injection diesel engine. A differentiation is made between the conditions in large bore and small bore diesel engines, particularly regarding the fuel impingement on the walls and the swirl and squish gas flow components. The model considers the fuel injected prior to the development of the flame, fuel injected in the flame, fuel deposited on the walls and the last part of the fuel delivered at the end of the injection process. The model is based on experimental results obtained in a single-cylinder, 4-valve, direct-injection, four-stroke-cycle, water-cooled, diesel engine equipped with a common rail fuel injection system. The engine is supercharged with heated shop air, and the exhaust back pressure is adjusted to simulate actual turbo-charged diesel engine conditions. The experiments covered a wide range of injection pressures, EGR rates, injection timings and swirl ratios. Correlations and 2-D maps are developed to show the effect of combinations of the above parameters on engine out emissions. Emphasis is made on the nitric oxide and soot measured in Bosch Smoke Units (BSU).

Visual experimental investigations of string cavitation and residual bubbles in the diesel nozzle and effects on initial spray structures

2018 ◽  
Vol 21 (3) ◽  
pp. 437-447 ◽  
Author(s):  
Genmiao Guo ◽  
Zhixia He ◽  
Zhengyang Zhang ◽  
Lian Duan ◽  
Wei Guan ◽  
...  
Keyword(s):  
High Speed ◽  
Fuel Injection ◽  
Fuel Mixture ◽  
Injection System ◽  
Experimental Investigations ◽  
Spray Cone ◽  
Nozzle Orifice ◽  
Diesel Nozzle ◽  
Initial Fuel ◽  
Opening And Closing

In this article, optical experiments on string cavitation and residual bubbles inside the real-size transparent tapered diesel nozzle and near-nozzle spray structures were performed based on a high-pressure common rail fuel injection system with a high-speed camera. The tapered nozzle which has high flow efficiency with weak or even no geometric cavitation has been widely used in commercial injectors, while there still exists string cavitation which may also influence the in-nozzle flow and subsequent spray. This article put focus on the tapered nozzle and the result indicated that the in-nozzle string cavitation provided a reasonable explanation for the two bumps of spray cone angles during the opening and closing stages of needle of real diesel engine injection processes. The suction and compression of air bubbles at the start and end stages of injection processes, and the various shot-to-shot near-nozzle spray patterns were captured and analyzed. These different near-nozzle spray patterns were attributed to the distribution of residual bubbles inside the nozzle orifice. The residual bubbles were survived from the last injection or sucked into the nozzle during needle opening stages. Stagnant bubbles were compressed and then accelerated the residual fuel which was close to the injector tip, leading to the formation of mushrooms. This study confirmed that the initial mushroom and the tail were generated by the interactions between the residual/sucked bubbles and the residual/initial fuel, and the leading mushroom was incurred by the combination of the transverse expansion of the jet and the laminar layer theory. This work pointed out and analyzed the new sources of the cycle-to-cycle variation of air/fuel mixture and spray.

Application of a diagnostic technique for evaluating the quality of the air–fuel mixture and the ignition quality of a spark-ignition reciprocating aircraft piston engine

2016 ◽  
Vol 232 (3) ◽  
pp. 571-582
Author(s):  
AK Antonopoulos ◽  
RG Papagiannakis ◽  
DT Hountalas
Keyword(s):  
Fuel Injection ◽  
Diagnostic Technique ◽  
Fuel Mixture ◽  
Spark Ignition ◽  
Performance Characteristics ◽  
Injection System ◽  
Specific Work ◽  
Piston Engine ◽  
Ignition System

The performance characteristics of an aircraft piston engine are affected mainly by the air–fuel mixture quality (i.e. condition of the fuel injection system) and by the spark timing and spark duration (i.e. condition of ignition system). Thus, the present work focuses on investigating the effect of both fuel injection and spark ignition systems on performance characteristics of two aircraft piston engines which are of the same type but have overhauled by two different workshops. The investigation is conducted by applying an existing diagnostic technique, which is based on the simultaneous recording and processing of two electric signals: one corresponding to cylinder pressure and the second corresponding to the ignition system. The basic characteristics of the proposed methodology are simplicity and field applicability on engines of this type. A detailed experimental investigation has been conducted on the aforementioned two aircraft piston engines on a dedicated test bench. From the results, it is revealed that the proposed diagnostic methodology provides reliable information for the effect of both the ignition and fuel injection systems on engine performance characteristics. The results derived from the specific work enable the comparative evaluation of the engines and their ignition and fuel injection systems. Finally, based on this first investigation, the proposed methodology seems to be promising, because it can be easily applied on any type of spark-ignited engine and especially on aircraft piston engine, where due to its geometry and multicylinder nature, the application of lab techniques on the field is, if not impossible, extremely difficult.

Sign in / Sign up

Export Citation Format

Share Document