scholarly journals Determination of cyclic filling length in gob-side entry retained with roadside filling and its application

2020 ◽  
Author(s):  
Zizheng Zhang ◽  
Jianbiao Bai ◽  
Xianyang Yu ◽  
Weijian Yu ◽  
Min Deng ◽  
...  
Keyword(s):  
Coal Seam ◽  
Coal Mine ◽  
Difference Method ◽  
Suggested Method ◽  
Stress Difference ◽  
Thick Coal Seam ◽  
Mechanics Model ◽  
Working Face ◽  
Geological Conditions ◽  
The Relationship

Abstract Gob-side entry retained with roadside filling (GER-RF) plays a key role in achieving coal mining without pillar and improving the coal resource recovery rate. Since there are few reports on the cyclic filling length of GER-RF, a method based on the stress difference method is proposed to determine the cyclic filling length of GER-RF. Firstly, a stability analysis mechanics model of the immediate roof above roadside filling area in GER was established, then the relationship between the roof stress distribution and the unsupported roof length was obtained by the stress difference method. According to the roof stability above roadside filling area based on the relationship between the roof stress and its tensile strength, the maximum unsupported roof length and rational cyclic filling length of GER-RF. Combined with the geological conditions of the 1103 thin coal seam working face of Heilong Coal Mine and the geological conditions of the 1301 thick coal seam working face of Licun Coal Mine, this suggested method was applied to determine that the rational cyclic filling lengths of GER-RF were 2.4 m and 3.2 m, respectively. Field trial tests show that the suggested method can effectively control the surrounding rock deformation along with rational road-in support and roadside support, and improve the filling and construction speed.

scholarly journals Determination of Cyclic Filling Length in Gob-Side Entry Retained with Roadside Filling and Its Application

2021 ◽  
Vol 2021 ◽  
pp. 1-16
Author(s):  
Zizheng Zhang ◽  
Jinlin Xin ◽  
Jianbiao Bai ◽  
Xianyang Yu ◽  
Weijian Yu ◽  
...  
Keyword(s):  
Coal Seam ◽  
Coal Mine ◽  
Difference Method ◽  
Suggested Method ◽  
Stress Difference ◽  
Thick Coal Seam ◽  
Mechanics Model ◽  
Working Face ◽  
Geological Conditions ◽  
The Relationship

Gob-side entry retained with roadside filling (GER-RF) plays a key role in achieving coal mining without pillar and improving the coal resource recovery rate. Since there are few reports on the cyclic filling length of GER-RF, a method based on the stress difference method is proposed to determine the cyclic filling length of GER-RF. Firstly, a stability analysis mechanics model of the immediate roof above the roadside filling area was established, and then, the relationship between the roof stress distribution and the unsupported roof length was obtained by the stress difference method. According to the roof stability above the roadside filling area based on the relationship between the roof stress and its tensile strength, the maximum unsupported roof length and rational cyclic filling length were determined. Combined with the geological conditions of the 1103 thin coal seam working face of Heilong Coal Mine and the 1301 thick coal seam working face of Licun Coal Mine, the suggested method was applied to determine that the rational cyclic filling lengths were 2.4 m and 3.2 m, respectively. Field trial tests show that the suggested method can effectively control the surrounding rock deformation along with rational road-in support and roadside support and improve the filling and construction speed.

scholarly journals Study of Gob-Side Entry Retaining Technology with Roof Cutting under Upper Roadway Condition

2021 ◽  
Vol 2021 ◽  
pp. 1-16
Author(s):  
Xingen Ma ◽  
Manchao He ◽  
Xuewei Sun ◽  
Jianfeng Li ◽  
Gang He ◽  
...  
Keyword(s):  
Coal Seam ◽  
Surrounding Rock ◽  
Pressure Relief ◽  
Application System ◽  
Thick Coal Seam ◽  
Working Face ◽  
Geological Conditions ◽  
Key Technologies ◽  
Releasing Effect ◽  
System Designs

Gob-side entry retaining technology with roof cutting (GERRC) has been widely used in flat and near-flat coal seam conditions, but its application under inclined coal seam is still very deficient. In order to further improve the application system of GERRC and overcome the application difficulties under special geological conditions, this paper takes the 43073 working face of Yixin coal mine as an example to research the GERRC with upper roadway under gently inclined thick coal seam. Firstly, the difficulties in the upper entry retaining with inclined coal seam are analyzed and the corresponding key technologies and system designs are put forward. Subsequently, the roof cutting and upper entry retaining are designed in detail according to geological conditions of test working face, and the roof cutting and pressure releasing effect is analyzed by numerical simulation to expound the stress distribution and pressure releasing mechanism of surrounding rock. Finally, the upper entry retaining field test is carried out to verify the feasibility and applicability of the technology and related designs. Through field monitoring, it is found that the weighting step increases significantly, the weighting strength decreases effectively on the roof cutting side, and the pressure relief effect is obvious. Meanwhile, the maximum roof to floor convergence is 361 mm and the maximum shrinkage of both sides is 280 mm, so the retained entry can meet the reuse requirement of adjacent working face.

Similarity simulation study on displacement and stress changes response to coal mining in Longdong coal mine, China

2020 ◽  
pp. qjegh2020-111
Author(s):  
Kai Huang ◽  
Long Xu ◽  
Fusheng Zha ◽  
Zhitang Lu ◽  
Jiwen Wu ◽  
...  
Keyword(s):  
Coal Seam ◽  
Coal Mine ◽  
Water Inrush ◽  
Coal Pillar ◽  
Working Face ◽  
Field Investigations ◽  
Geological Conditions ◽  
Stress Changes ◽  
Continuous Mining ◽  
The Stability

The complicated geological conditions, including the Fault Sun, in East No. 2 mining sub-area of the Longdong coal mine will influence the stability of strata during mining, leading to serious geological hazards. To circumvent this issue, a similarity simulation experiment was designed and performed in this study, in which the failure characteristics and evolution of displacement and stress within the strata were investigated, and the optimum width of a waterproof coal pillar was determined. The results showed that, as the working face progressed, the coal seam roof gradually deformed, from initial caving of the immediate roof to complete movement and curved subsidence of the entire roof. Significant changes in displacement and stress within the coal seam roof were recorded, and these increased during continuous mining activity. Displacement and stress difference on either side of the fault gradually increased and reached remarkable values with increase in mining distance. On the basis of the experiment results, water inrush is believed to be caused by the interaction between mining and the fault, and, as calculated from parameters collected in field investigations, a waterproof coal pillar of 50 m width should be established to prevent Fault Sun activation, thereby reducing the risk of water inrush from neighbouring aquifers.

scholarly journals Force-Fracture Characteristics of the Roof above Goaf in a Steep Coal Seam: A Case Study of Xintie Coal Mine

Geofluids ◽  
2019 ◽  
Vol 2019 ◽  
pp. 1-11 ◽  
Author(s):  
Hong-sheng Tu ◽  
Shi-hao Tu ◽  
De-fu Zhu ◽  
Ding-yi Hao ◽  
Kai-jun Miao
Keyword(s):  
Theoretical Analysis ◽  
Coal Seam ◽  
Coal Mine ◽  
Thin Plates ◽  
Support Pressure ◽  
Similar Distribution ◽  
Operational Parameters ◽  
Working Face ◽  
Geological Conditions ◽  
Roof Deformation

After coal is extracted from a working face in a steep coal seam (SCS), the immediate roof tends to cave in and refill the lower part of the goaf. Based on the geological conditions of a work area in a SCS and the characteristics of roof caving, this study proposed a formula for the width of the backfill in the goaf and analyzed the main factors influencing it. Based on the small-deflection theory for elastic thin plates, a working face model was created for the mechanical analysis of the main roof above a SCS before the roof fractures for the first time. Then, a roof deflection equation was derived for the estimation roof deformation under the action of both the load from overlying strata and the support provided by the backfill in the goaf. The theoretical analysis combined with the actual operational parameters at the Zuoqipian working face in #49 seam of Xintie Coal Mine shows that the maximum roof deflection is around 0.8 m and occurs at a location 39 m from the upper end of the working face. Fractures will first develop in the upper sections of the frontal and rear walls of the face and the middle of the upper suspended roof due to tension or shearing and ultimately form an E-shaped pattern. The measured support pressure and the roof deformation obtained by theoretical analysis show a similar distribution pattern, indirectly confirming the accuracy of the theoretical results.

scholarly journals Disastrous Mechanism of Water Discharge in Abandoned Gob above the Stope in Mining Extra-Thick Coal Seam

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Haixiao Lin ◽  
Feng Yang ◽  
Zhengzheng Cao ◽  
Yue Wang ◽  
Xiaojian Jiao
Keyword(s):  
Coal Seam ◽  
Water Discharge ◽  
Mining Area ◽  
Thick Coal Seam ◽  
Research Results ◽  
Key Stratum ◽  
Working Face ◽  
Geological Conditions ◽  
Induced Fractures ◽  
Seam Mining

The Datong mining area is a typical double system coal seam mining area in China, where the Jurassic and Carboniferous coal seams are mined simultaneously. The upper Jurassic coal seam has been largely mined, leaving a large amount of gob area. Besides, a large amount of harmful water is accumulated. With the exploitation of the 3-5# extra-thick coal seam in the Carboniferous system, the scope of overburden damage is greatly increasing, and the mining fracture field is further developed. Once the mining-induced fractures connect with the overlying gob, it is easy to induce the water discharge disaster. With the mining geological conditions of the 8202 working face in the Tongxin coal mine as references, the disastrous mechanism of water discharge in the abandoned gob above the stope in the mining extra-thick coal seam is researched by numerical simulation with the UDEC numerical software, and the research results are obtained. The water in the overlying gob percolates through the mining-induced fractures in the higher key layer forming a “shower” seepage pattern. The water in the above gob converges in the key fracture channel, flowing into the working face. The seepage in the fractures in the high key stratum experiences the process of increase, decrease, and stabilization, related with the stretching and extrusion deformation between the high key stratum blocks. Compared with other fractures, the flow rates in the No.2 and No.4 fractures in the far field key lay are larger, because the fractures are in the tension state, forming the “saddle-shaped” flow pattern. The influencing distance of mining-induced seepage is about 80 m in front of the working face. The research results provide a guided reference for the prediction and prevention of water discharge disaster in an abandoned gob above the stope in a mining extra-thick coal seam.

scholarly journals Characteristics of Stratum Structure and Fracture Evolution in Stratified Mining of Shallow Buried High-Gas-Thick Coal Seam by Similarity Simulation

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-18
Author(s):  
Qin Guangpeng ◽  
Cao Jing ◽  
Wang Chao ◽  
Wu Shuo ◽  
Zhai Minghua
Keyword(s):  
Coal Seam ◽  
Coal Mine ◽  
Coal Pillar ◽  
Structure Evolution ◽  
Thick Coal Seam ◽  
Fracture Structure ◽  
Working Face ◽  
Rock Structure ◽  
Type Fracture ◽  
Overlying Strata

The stratified mining of super thick coal seam is a process of repeated disturbance of the top roof, especially in the lower stratification, the upper complex rock layer has a greater settlement space, resulting in great changes in the strata structure and fissure distribution. The main coal seam thickness of Rujigou Coal Mine exceeds 20 m, due to the high gas content of the coal seam, it is prone to spontaneous combustion, and the stratified mining method is adopted. When a small-size section coal pillar (less than 10 m) is used, the complex rock structure evolution and fissure development characteristics during the stratified mining of shallow buried thick coal seam will directly affect the movement of gas transportation between the working face and the goaf and will directly affect the safety of the working face. Taking Rujigou coal mine as engineering background, this paper analyzes the breaking structure, fracture development, and evolution law of overlying strata in different layers and different sections of coal seam when the buried depth is shallow, and the extra-thick coal seam is stratified mining. The results show that in the process of stratified mining, the overlying strata break, in addition to the whole trapezoidal failure structure, will also form a local F type fracture structure, and with the stratified downward mining, the F type fracture structure will continue to move up and disappear until it is compacted. The “V” type and “U” type subsidence characteristics of different strata overburden are presented after mining in stratified working face of extra-thick coal seam, and the subsidence amount is approximately symmetrical distribution along the middle line of goaf. In the mining process of the lower part of the layer, the end broken rock block is easy to slip along the hinge point by the hinged rock beam structure, and the sliding instability occurs. In the process of stratified mining of ultrathick coal seam, the main fissure of overburden is mainly longitudinal fissure, and it is very easy to form through with the upper layer and will finally connect with the surface under the condition of shallow buried depth. The inclined cracks connected with the adjacent goaf are formed above the coal pillar of the section, which becomes the passage of gas migration in the goaf. The research conclusion shows that for the stratified mining of high gas thick coal seam, special attention should be paid to the treatment of the gas on the stratified working face. In addition to the conventional gas treatment measures such as coal seam prepumping, the buried pipe pumping in the mining area can also be adopted, which can effectively reduce the gas concentration of the working surface.

Reasonable Entry Layout of Lower Seam in Multi-Seam Mining Based on Numerical Simulation

2013 ◽  
Vol 295-298 ◽  
pp. 2980-2984
Author(s):  
Xiang Qian Wang ◽  
Da Fa Yin ◽  
Zhao Ning Gao ◽  
Qi Feng Zhao
Keyword(s):  
Numerical Simulation ◽  
Stress Distribution ◽  
Coal Seam ◽  
Coal Mine ◽  
Abutment Pressure ◽  
Surrounding Rock ◽  
Geological Conditions ◽  
Seam Mining

Based on the geological conditions of 6# coal seam and 8# coal seam in Xieqiao Coal Mine, to determine reasonable entry layout of lower seam in multi-seam mining, alternate internal entry layout, alternate exterior entry layout and overlapping entry layout were put forward and simulated by FLAC3D. Then stress distribution and displacement characteristics of surrounding rock were analyzed in the three ways of entry layout, leading to the conclusion that alternate internal entry layout is a better choice for multi-seam mining, for which makes the entry located in stress reduce zone and reduces the influence of abutment pressure of upper coal seam mining to a certain extent,. And the mining practice of Xieqiao Coal Mine tested the results, which will offer a beneficial reference for entry layout with similar geological conditions in multi-seam mining.

scholarly journals A numerical simulation of realistic top coal caving intervals under different top coal thicknesses in longwall top coal caving working face

2021 ◽  
Author(s):  
Chuang Liu ◽  
Huamin Li
Keyword(s):  
Numerical Simulation ◽  
Coal Seam ◽  
Distinct Element ◽  
Simulation Models ◽  
Simulation Software ◽  
Thick Coal Seam ◽  
Coal Recovery ◽  
Working Face ◽  
Longwall Top Coal Caving ◽  
Selection Of

Abstract In the process of longwall top coal caving, the selection of the top coal caving interval along the advancing direction of the working face has an important effect on the top coal recovery. To explore a realistic top coal caving interval of the longwall top coal caving working face, longwall top coal caving panel 8202 in the Tongxin Coal Mine is used as an example, and 30 numerical simulation models are established by using Continuum-based Distinct Element Method (CDEM) simulation software to study the top coal recovery with 4.0 m, 8.0 m, 12.0 m, 16.0 m, 20.0 m and 24.0 m top coal thicknesses and 0.8 m, 1.0 m, 1.2 m, 1.6 m and 2.4 m top coal caving intervals. The results show that with an increase in the top coal caving interval, the single top coal caving amount increases. The top coal recovery is the highest with a 0.8 m top coal caving interval when the thickness of the top coal is less than 4.0 m, and it is the highest with a 1.2 m top coal caving interval when the coal seam thickness is greater than 4.0 m. These results provide a reference for the selection of a realistic top coal caving interval in thick coal seam caving mining.

Sign in / Sign up

Export Citation Format

Share Document