scholarly journals Air, helium and water leakage in rubber O-ring seals with application to syringes

2021 ◽  
Author(s):  
Carine Huon ◽  
Avinash Tiwari ◽  
Cinzia Rotella ◽  
Paolo Mangiagalli ◽  
bo persson
Keyword(s):  
Surface Roughness ◽  
Fluid Flow ◽  
Surface Energy ◽  
Viscoelastic Properties ◽  
Gas Flow ◽  
Laplace Pressure ◽  
Water Leakage ◽  
Random Surface ◽  
Interfacial Surface ◽  
Interfacial Fluid

Abstract We study the leakage of fluids (liquids or gases) in syringes with glass barrel, steel plunger and rubber O-ring stopper. The leakrate depends on the interfacial surface roughness and on the viscoelastic properties of the rubber. Random surface roughness is produced by sandblasting the rubber O-rings. We present a very simple theory for gas flow which takes into account both the diffusive and ballistic flow. The theory shows that the interfacial fluid flow (leakage) channels are so narrow that the gas flow is mainly ballistic (the so called Knudsen limit). We compare the leakrate obtained using air and helium. For barrels filled with water we observe no leakage even if leakage occurs for gases. We interpret this as resulting from capillary (Laplace pressure or surface energy) effects.

Introduction

2005 ◽  
pp. 1-46
Keyword(s):  
Surface Roughness ◽  
Contact Angle ◽  
Fluid Flow ◽  
Surface Energy ◽  
Environmental Aspects ◽  
Solid Materials ◽  
Principal Characteristics ◽  
Parent Materials ◽  
Joint Gap ◽  
New Phase

Abstract Brazing and soldering jointly represent one of several methods for joining solid materials. This chapter summarizes the principal characteristics of the various joining methods. It then discusses key parameters of brazing including surface energy and tension, wetting and contact angle, fluid flow, filler spreading characteristics, surface roughness of components, dissolution of parent materials, new phase formations, significance of the joint gap, and the strength of metals. The chapter also describes issues in processing aspects that must be considered when designing a joint, and the health, safety, and environmental aspects of brazing.

A new method for quantifying the blocking of coated paperboard

TAPPI Journal ◽  
2010 ◽  
Vol 9 (5) ◽  
pp. 29-35 ◽  
Author(s):  
PAULINE SKILLINGTON ◽  
YOLANDE R. SCHOEMAN ◽  
VALESKA CLOETE ◽  
PATRICE C. HARTMANN
Keyword(s):  
Surface Roughness ◽  
Fatty Acid ◽  
Surface Energy ◽  
Film Thickness ◽  
External Factors ◽  
Additive Concentration ◽  
Pressure Surface ◽  
Fatty Acid Amides ◽  
Coated Surfaces ◽  
Definite Period

Blocking is undesired adhesion between two surfaces when subjected to pressure and temperature constraints. Blocking between two coated paperboards in contact with each other may be caused by inter-diffusion, adsorption, or electrostatic forces occurring between the respective coating surfaces. These interactions are influenced by factors such as the temperature, pressure, surface roughness, and surface energy. Blocking potentially can be reduced by adjusting these factors, or by using antiblocking additives such as talc, amorphous silica, fatty acid amides, or polymeric waxes. We developed a method of quantifying blocking using a rheometer. Coated surfaces were put in contact with each other with controlled pressure and temperature for a definite period. We then measured the work necessary to pull the two surfaces apart. This was a reproducible way to accurately quantify blocking. The method was applied to determine the effect external factors have on the blocking tendency of coated paperboards, i.e., antiblocking additive concentration, film thickness, temperature, and humidity.

The effect of a footprint on perceived surface roughness

1986 ◽  
Vol 405 (1829) ◽  
pp. 303-327 ◽  
Keyword(s):  
Surface Roughness ◽  
Weighting Function ◽  
Sampling Interval ◽  
Asymptotic Convergence ◽  
Reference Surface ◽  
Two Dimensional ◽  
Random Surface ◽  
Spectral Density Functions ◽  
Continuous Theory ◽  
Discrete Theory

A two-dimensional homogeneous random surface { y ( X )} is generated from another such surface { z ( X )} by a process of smoothing represented by y ( X ) = ∫ ∞ d u w ( u – X ) z ( u ), where w ( X ) is a deterministic weighting function satisfying certain conditions. The two-dimensional autocorrelation and spectral density functions of the smoothed surface { y ( X )} are calculated in terms of the corresponding functions of the reference surface { z ( X )} and the properties of the ‘footprint’ of the contact w ( X ). When the surfaces are Gaussian, the statistical properties of their peaks and summits are given by the continuous theory of surface roughness. If only sampled values of the surface height are available, there is a corresponding discrete theory. Provided that the discrete sampling interval is small enough, profile statistics calculated by the discrete theory should approach asymptotically those calculated by the continuous theory, but it is known that such asymptotic convergence may not occur in practice. For a smoothed surface { y ( X )} which is generated from a reference surface { z ( X )} by a ‘good’ footprint of finite area, it is shown in this paper that the expected asymptotic convergence does occur always, even if the reference surface is ideally white. For a footprint to be a good footprint, w ( X ) must be continuous and smooth enough that it can be differentiated twice everywhere, including at its edges. Sample calculations for three footprints, two of which are good footprints, illustrate the theory.

Investigation of surface roughness effects on fluid flow in passive micromixer

2013 ◽  
Vol 20 (12) ◽  
pp. 2261-2269 ◽  
Author(s):  
Gaurav Pendharkar ◽  
Raghavendra Deshmukh ◽  
Rajendra Patrikar
Keyword(s):  
Surface Roughness ◽  
Fluid Flow ◽  
Roughness Effects ◽  
Passive Micromixer

Laminar Forced Convection in Annular Microchannels With Slip Flow Regime

2009 ◽  
Author(s):  
Arman Sadeghi ◽  
Abolhassan Asgarshamsi ◽  
Mohammad Hassan Saidi
Keyword(s):  
Nusselt Number ◽  
Fluid Flow ◽  
Aspect Ratio ◽  
Boundary Conditions ◽  
Knudsen Number ◽  
Gas Flow ◽  
Slip Flow ◽  
Outer Wall ◽  
Graphical Form ◽  
Uniform Temperature

Fluid flow and heat transfer at microscale have attracted an important research interest in recent years due to the rapid development of microelectromechanical systems (MEMS). Fluid flow in microdevices has some characteristics which one of them is rarefaction effect related with gas flow. In this research, hydrodynamically and thermally fully developed laminar rarefied gas flow in annular microducts is studied using slip flow boundary conditions. Two different cases of the thermal boundary conditions are considered, namely: uniform temperature at the outer wall and adiabatic inner wall (Case A) and uniform temperature at the inner wall and adiabatic outer wall (Case B). Using the previously obtained velocity distribution, energy conservation equation subjected to relevant boundary conditions is numerically solved using fourth order Runge-Kutta method. The Nusselt number values are presented in graphical form as well as tabular form. It is realized that for the case A increasing aspect ratio results in increasing the Nusselt number, while the opposite is true for the case B. The effect of aspect ratio on Nusselt number is more notable at smaller values of Knudsen number, while its effect becomes slighter at large Knudsen numbers. Also increasing Knudsen number leads to smaller values of Nusselt number for the both cases.

A look into the interaction of metal oxide thin films with biological media: Albumin and Fibrinogen adsorption

2012 ◽  
Vol 1376 ◽  
Author(s):  
P. Silva-Bermudez ◽  
S. Muhl ◽  
M. Rivera ◽  
S. E. Rodil
Keyword(s):  
Surface Roughness ◽  
Surface Energy ◽  
Protein Adsorption ◽  
Photoelectron Spectroscopy ◽  
Ex Situ ◽  
Polar Component ◽  
Metal Oxide Thin Films ◽  
Adsorbed Protein ◽  
Major Chemical ◽  
Fibrinogen Adsorption

ABSTRACTIn the present work, the adsorption of albumin and fibrinogen on Ta, Nb, Ti and Zr oxidesthin films deposited on Si (100) wafers by magnetron sputtering was studied in order to get a better understanding of the correlation among the surface properties of these oxides and the protein adsorption phenomena on their surfaces. The surface energy, hydrophobicity, chemical composition, roughness and atomic order of the films were characterized. The films were immersedfor 45 minutes in single protein solutions; either albumin or fibrinogenand the adsorbed protein layer on the films was studied ex-situ in a dry ambient using bothX-ray photoelectron spectroscopy and atomic force microscopy.The adsorption of albumin and fibrinogen on the films modified the surface morphology and decreased the surface roughness for all the four different metal oxides. The XPS results confirmed the presence of the protein on the surface of the films and showed that the two proteins studied were adsorbed without undergoing a major chemical decomposition. A correlation between the surface roughness,the polar component of the surface energy of the films and the atomic percentage of nitrogen on the films after protein adsorption, an indirect signal of the amount of protein adsorbed, was found for albumin and fibrinogen adsorption on Ta, Nb and Ti oxides; the largest the roughness or the polar component the largest amount of adsorbed protein.

Computational Fluid Dynamics Study of New Vacuum Degassing Process

2009 ◽  
Vol 4 (3) ◽  
Author(s):  
Manas Kumar Mondal ◽  
Govind Sharan Gupta ◽  
Shin-ya Kitamura ◽  
Nobuhiro Maruoka
Keyword(s):  
Fluid Flow ◽  
Gas Flow ◽  
Low Carbon Steel ◽  
Momentum Balance ◽  
Low Carbon ◽  
Decarburization Rate ◽  
Vacuum Degassing ◽  
Liquid Phases ◽  
New Process ◽  
Flow Phenomena

Recently, the demand of the steel having superior chemical and physical properties has increased for which the content of carbon must be in ultra low range. There are many processes which can produce low carbon steel such as tank degasser and RH (Rheinstahl-Heraeus) processes. It has been claimed that using a new process, called REDA (Revolutionary Degassing Activator), one can achieve the carbon content below 10ppm in less time. REDA process, in terms of installment cost, is in between the tank degasser and RH processes. As such, REDA process has not been studied thoroughly. Fluid flow phenomena affect the decarburization rate the most besides the chemical reaction rate. Therefore, momentum balance equations along with k-? turbulent model have been solved for gas and liquid phases in two-dimension (2D) for REDA process. The fluid flow phenomena have been studied in details for this process by varying gas flow rate, depth of immersed snorkel in the steel, diameter of the snorkel and change in vacuum pressure. It is found that the design of the snorkel affects the melt circulation of the bath significantly.

Sign in / Sign up

Export Citation Format

Share Document