scholarly journals Determination of average relative capital investment of 30–125 MW combined-cycle plants commissioned at Russian thermal power plants in 2015–2020. Comparative analysis with data obtained in 2010–2014

2022 ◽  
Vol 25 (6) ◽  
pp. 762-772
Author(s):  
E. L. Stepanova ◽  
A. P. Ovchinnikov
Keyword(s):  
Fuel Consumption ◽  
Thermal Energy ◽  
Gas Turbines ◽  
Energy Supply ◽  
Capital Investment ◽  
Power Plants ◽  
Thermal Power ◽  
Combined Cycle ◽  
Preliminary Evaluation ◽  
Thermal Power Plants

The present work examines average relative capital investment and fuel consumption for electric and thermal energy supply of the combined-cycle plants having 30–125 MW gas turbines commissioned at Russian thermal power plants in 2015–2020. In this work, we used general calculation methods of average relative capital investments and fuel consumption for the electrical and thermal energy supply using power equipment of thermal power plants. To assess the scope of commissioning gas turbines incorporated into the combined-cycle plants, they were classified into three groups by electrical power: 30–59 MW, 60–99 MW and 100–125 MW. The scope of commissioning gas turbines incorporated into the Russian combined-cycle plants in 2015–2020 was analysed. The average relative capital invest-ment in combined-cycle plants having 30–125 MW gas turbines, as well as the average specific fuel consumption for the electrical and thermal energy supply, were calculated. The calculations were carried out for each part of combined-cycle plants integrated into thermal power plants with a breakdown by seven Unified Energy Systems of Russia. The quantita-tive commissioning of gas turbines is compared for the periods from 2010 to the economic crisis of 2014 and after 2014 to the present: a ~2.5-fold decrease is demonstrated. A preliminary evaluation of the increase in average relative capital investment in combined-cycle plants having gas turbines of the same electric power was performed.

scholarly journals Fuel consumption of thermal power technologies under maneuvering modes

2020 ◽  
Vol 2020 (4) ◽  
pp. 45-49
Author(s):  
V.S. Kobernik ◽  
Keyword(s):  
Power Systems ◽  
Fuel Consumption ◽  
Fluidized Bed ◽  
Thermal Energy ◽  
Gas Turbines ◽  
Power Plants ◽  
Thermal Power ◽  
Electric Energy ◽  
Coal Fuel ◽  
Fluidized Bed Boilers

A characteristic feature of the present day development of power engineering lies in the increase in the unevenness of power systems schedules. The structure of generating powers of Ukrainian energy engineering is overloaded with basic powers and characterized by a sharp deficit of maneuvering wanes. To cover the uneven load of the power system during the operation of existing and construction of new power plants, it is necessary to take into account the possibility of their operation under maneuvering modes. This paper determines the influence of work of power plants i under maneuvering modes on the specific consumption of conditional fuel on the released electric energy at working on gas or coal fuel. Fuel consumption for starting of a unit depends on its type and downtime in reserve. The use of steam–and–gas facilities and gas turbines helps to enhance the maneuverability of power plants. Alternative options for the development of thermal energy are the introduction of gas–piston power plants and power units with fluidized–bed boilers. We present formulas for the calculations of fuel consumption on by power units for start–ups and specific consumptions depending on the load and degree of their involvement to regulating loads for different thermal energy technologies: steam–turbine condensation and district heating power units; steam–and–gas and gas turbine plants; gas piston installations; power units with fluidized bed boilers. For enhancing the maneuverability of power plants, working on fossil fuels, their modernization and renewal of software are necessary. Quantitative assessment of the efficiency of power units and separate power plants during their operation under variable modes is important for forecasting the structure of generating capacities of power systems, the need to introduce peak and semi–peak capacities, the choice of the most profitable composition of operating equipment at different schedules of electrical loads Keywords: thermal power, power unit, maneuverable mode, electrical load, specific fuel consumption

Development of Integration Methods for Thermal Energy Storages Into Power Plant Processes

2016 ◽  
Author(s):  
Clemens Schneider ◽  
Sebastian Braun ◽  
Torsten Klette ◽  
Steffen Härtelt ◽  
Alexander Kratzsch
Keyword(s):  
Energy Storage ◽  
Power Plant ◽  
Thermal Energy ◽  
Heat Sink ◽  
Energy Supply ◽  
Power Plants ◽  
Thermal Power ◽  
Test Facility ◽  
Thermal Power Plants ◽  
Load Reduction

Germany’s current energy policy is focused on the replacement of the conventional powered electrical energy supply system by renewable sources. This leads to increasing requirements on the flexibility for the conventional thermal power plants. Larger differences between energy supply from renewable energy sources and energy demand in the grid lead to high dynamic requirements with respect to the load change transients. Furthermore, a reduction of the required minimum load of existing thermal power plants is necessary. The existing power plants are indispensable for securing the network stability of the power grid. Accordingly, activities to improve the flexibility of existing power plants are required. By the use of thermal energy storage (TES) it is possible to increase the load change transient. Furthermore, it is possible to temporarily provide an increased generator power and reduce the minimum technical load of the unit. Currently, there is no closed methodical approach for the load profile-dependent and location-based dimensioning and integration of TES into thermal power plants. The aim is to generate contributions for the development of a universal design method. This requires the provision of characteristics for dimensioning and integration of TES into thermal processes. For this purpose, it is necessary to derive quantifiable information on the required capacity, performance and stationary and dynamic operating conditions. Starting from analyzing the anticipated, site-specific load profiles the derivation of concepts for technical implementation, feedback on the process and cost of the thermal storage unit takes place. In order to investigate the technical feasibility, the implementation of storage and the associated control concepts as well as to validate the developed design models, the test facility THERESA has been built at the University of Applied Sciences in Zittau (Germany). The acronym THERESA is the abbreviation for thermal energy storage facility. This test facility includes a reconstructed thermal water-steam process, similar to a power plant with integrated TES. The test facility is unique in Germany and enables the delivery of saturated steam up to 160 bars at 347 ° and superheated steam up to 60 bars at 350 °C with an overall thermal power of 640 kW. The design, planning and construction of the facility took 3 years and required an investment volume of 3 mill. Euro. The facility includes two preheater stages, steam generator, super heater, direct TES with mixing preheater and a heat sink. The TES with a volume of 600 L as well as the mixing preheater are prototypes which developed for the special requirements of the facility. Based on this facility, it is possible to investigate methods for the flexibilization of thermal power plants with TES under realistic parameters. Furthermore, the test facility allows the development of control and regulatory approaches as well as the validation of simulation models for process expansion of thermal power plants. Initial investigations show the impact of a simulated load reduction at the heat sink on the system behavior. Here, the load reduction takes place from the heat sink in the storage without changing the steam production. The development and construction of the test facility were funded by the Free State of Saxony and the European Union. The further work on the development of the integration methods are funded by the European Social Fund ESF.

Industrial Users Choose Fuel Flexible GT11N2 for Burning Blast Furnace Gas in Combined Cycle Power Plants

1997 ◽  
Author(s):  
G. Gnädig ◽  
K. Reyser ◽  
W. Fischer ◽  
J. Schmidli
Keyword(s):  
Blast Furnace ◽  
Gas Turbines ◽  
Power Plants ◽  
High Efficiency ◽  
Environmental Regulations ◽  
Thermal Power ◽  
Combined Cycle ◽  
Thermal Power Plants ◽  
Industrial Plants ◽  
Blast Furnace Gas

Stricter environmental regulations and the need for high-efficiency energy generation have led an increasing number of industrial users to investigate alternatives to burning waste gases from the industrial plants in conventional thermal power plants. Combined cycle power plants using gas turbines capable of burning low-caloric fuels such as blast furnace gas can meet these requirements with thermal efficiencies of more than 45%.

Greenhouse Gas Emissions Calculation Methodology in Thermal Power Plants: Case Study of Iran and Comparison With Canada

2008 ◽  
Author(s):  
Farshid Zabihian ◽  
Alan S. Fung
Keyword(s):  
Climate Change ◽  
Greenhouse Gas ◽  
Global Climate Change ◽  
Gas Turbines ◽  
Electricity Generation ◽  
Power Plants ◽  
Global Climate ◽  
Thermal Power ◽  
Ghg Emissions ◽  
Thermal Power Plants

Nowadays, the global climate change has been a worldwide concern and the greenhouse gases (GHG) emissions are considered as the primary cause of that. The United Nations Conference on Environment and Development (UNCED) divided countries into two groups: Annex I Parties and Non-Annex I Parties. Since Iran and all other countries in the Middle East are among Non-Annex I Parties, they are not required to submit annual GHG inventory report. However, the global climate change is a worldwide phenomenon so Middle Eastern countries should be involved and it is necessary to prepare such a report at least unofficially. In this paper the terminology and the methods to calculate GHG emissions will first be explained and then GHG emissions estimates for the Iranian power plants will be presented. Finally the results will be compared with GHG emissions from the Canadian electricity generation sector. The results for the Iranian power plants show that in 2005 greenhouse gas intensity for steam power plants, gas turbines and combined cycle power plants were 617, 773, and 462 g CO2eq/kWh, respectively with the overall intensity of 610 g CO2eq/kWh for all thermal power plants. This GHG intensity is directly depend on efficiency of power plants. Whereas, in 2004 GHG intensity for electricity generation sector in Canada for different fuels were as follows: Coal 1010, refined petroleum products 640, and natural gas 523 g CO2eq/kWh, which are comparable with same data for Iran. For average GHG intensity in the whole electricity generation sector the difference is much higher: Canada 222 vs. Iran 610g CO2eq/kWh. The reason is that in Canada a considerable portion of electricity is generated by hydro-electric and nuclear power plants in which they do not emit significant amount of GHG emissions. The average GHG intensity in electricity generation sector in Iran between 1995 and 2005 experienced 13% reduction. While in Canada at the same period of time there was 21% increase. However, the results demonstrate that still there are great potentials for GHG emissions reduction in Iran’s electricity generation sector.

scholarly journals STATE AND PROSPECTS OF THERMAL POWER GENERATION IN THE CONDITIONS OF UKRAINE’S COURSE ON CARBON-FREE ENERGY

2021 ◽  
pp. 4-16
Author(s):  
M.V. Cherniavskyi
Keyword(s):  
Power Generation ◽  
Free Energy ◽  
Power System ◽  
Fuel Consumption ◽  
Power Plants ◽  
Thermal Power ◽  
Specific Fuel Consumption ◽  
Regulatory Function ◽  
Thermal Power Plants ◽  
Thermal Power Generation

The structure of electricity cost formation for consumers, including depending on the cost of TPP generation, «green» energy and other sources, is investigated, and the main conditions of the efficient regulatory function fulfillment in the power system by thermal power generation in the conditions of Ukraine's course on carbon-free energy are formulated. It is shown that excessive electricity losses in networks and, especially, accelerated increase of the share of «green» generation, much more expensive than nuclear, hydro and thermal, mainly contribute to the growth of electricity costs for non-household consumers and the need to raise tariffs for the population. This accelerated increase directly contradicts the Paris Climate Agreement, according to which plans to reduce Ukraine’s greenhouse gas emissions must be developed taking into account available energy resources and without harming its own economy. The dependences of the specific fuel consumption on the average load and the frequency of start-stops of units are found and it is shown that the increased specific fuel consumption on coal TPPs is an inevitable payment for their use as regulating capacities of UES of Ukraine. In this case, the higher the proportion of «green» generation and a smaller proportion of generating thermal power plants, especially increasing specific fuel consumption. It is proved that in the conditions of growth of the share of «green» generation in Ukraine the share of production of pulverized coal thermal power plants should be kept at the level of not less than 30 % of the total electricity generation. It is substantiated that a necessary condition for coal generation to perform a proper regulatory role in the power system is to introduce both environmental and technical measures, namely — reducing the suction of cold air to the furnace and other boiler elements, restoring condensers and cooling systems, etc. An important factor in reducing the average level of specific fuel consumption is also the reduction of coal burn-out at thermal power plants, where it still remains significant, due to the transfer of power units to the combustion of bituminous coal concentrate. Bibl. 12, Fig. 5, Tab. 5.

Parameterization of High Solar Share Gas Turbine Systems

2012 ◽  
Author(s):  
Stephan Heide ◽  
Christian Felsmann ◽  
Uwe Gampe ◽  
Sven Boje ◽  
Bernd Gericke ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Power Plants ◽  
Planning Process ◽  
Pressure Ratio ◽  
Thermal Power ◽  
Combined Cycle ◽  
Process Models ◽  
Solar Thermal ◽  
Thermal Power Plants ◽  
Solar Thermal Power

Existing solar thermal power plants are based on steam turbine cycles. While their process temperature is limited, solar gas turbine (GT) systems provide the opportunity to utilize solar heat at a much higher temperature. Therefore there is potential to improve the efficiency of future solar thermal power plants. Solar based heat input to substitute fuel requires specific GT features. Currently the portfolio of available GTs with these features is restricted. Only small capacity research plants are in service or in planning. Process layout and technology studies for high solar share GT systems have been carried out and have already been reported by the authors. While these investigations are based on a commercial 10MW class GT, this paper addresses the parameterization of high solar share GT systems and is not restricted to any type of commercial GT. Three configurations of solar hybrid GT cycles are analyzed. Besides recuperated and simple GT with bottoming Organic Rankine Cycle (ORC), a conventional combined cycle is considered. The study addresses the GT parameterization. Therefore parametric process models are used for simulation. Maximum electrical efficiency and associated optimum compressor pressure ratio πC are derived at design conditions. The pressure losses of the additional solar components of solar hybrid GTs have a different adversely effect on the investigated systems. Further aspects like high ambient temperature, availability of water and influence of compressor pressure level on component design are discussed as well. The present study is part of the R&D project Hybrid High Solar Share Gas Turbine Systems (HYGATE) which is funded by the German Ministry for the Environment, Nature and Nuclear Safety and the Ministry of Economics and Technology.

scholarly journals Review of solid particle materials for heat transfer fluid and thermal energy storage in solar thermal power plants

2019 ◽  
Vol 1 (4) ◽  
Author(s):  
Alejandro Calderón ◽  
Camila Barreneche ◽  
Anabel Palacios ◽  
Mercè Segarra ◽  
Cristina Prieto ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Energy Storage ◽  
Solid Particle ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Power Plants ◽  
Thermal Power ◽  
Heat Transfer Fluid ◽  
Thermal Power Plants ◽  
Solar Thermal Power
Sign in / Sign up

Export Citation Format

Share Document