Study of Gas Shortcut Flow Rate in Cyclone with Different Inlet Section Angles Using Response Surface Methodology

2009 ◽  
Vol 7 (1) ◽  
Author(s):  
Fuping Qian ◽  
Xingwei Huang ◽  
Mingyao Zhang
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Flow Rate ◽  
Numerical Solutions ◽  
Inlet Section ◽  
Statistical Software ◽  
Vortex Finder ◽  
Computational Fluid Dynamics Cfd

Numerical simulations of cyclones with various vortex finder dimensions and inlet section angles were performed to study the gas shortcut flow rate. The numerical solutions were carried out using commercial computational fluid dynamics (CFD) code Fluent 6.1. A prediction model of the gas shortcut flow rate was obtained based on response surface methodology by means of the statistical software program (Minitab V14). The results show that the length of the vortex finder insertion, the vortex finder diameter and the inlet section angle play an important role in influencing the gas shortcut flow rate. The gas shortcut flow rate decreases when increasing the inlet section angle, and increases when increasing the vortex finder diameter and decreasing the length of the vortex finder insertion. Compared with the effect of the length of the vortex finder insertion on the shortcut flow rate, the effect of the vortex finder diameter on the gas shortcut flow rate seems more pronounced. The effect of the vortex finder dimension on the gas shortcut flow rate is changed with the different inlet section angles, i.e., the effects of the vortex finder dimension of the conventional cyclone (the inlet section angle is 0º) on the gas shortcut flow rate is stronger than the cyclone with 30º and 45º inlet section angles.

scholarly journals Effect of hydraulic and geometric factors upon leakage flow rate in pressurized pipes

RBRH ◽  
2021 ◽  
Vol 26 ◽  
Author(s):  
Mayara Francisca da Silva ◽  
Fábio Veríssimo Gonçalves ◽  
Johannes Gérson Janzen
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Rate ◽  
Leakage Flow ◽  
Cfd Simulations ◽  
Mean Velocity ◽  
Leakage Flow Rate ◽  
Geometric Factors ◽  
Leakage Area ◽  
Computational Fluid Dynamics Cfd

ABSTRACT Computational Fluid Dynamics (CFD) simulations of a leakage in a pressurized pipe were undertaken to determine the empirical effects of hydraulic and geometric factors on the leakage flow rate. The results showed that pressure, leakage area and leakage form, influenced the leakage flow rate significantly, while pipe thickness and mean velocity did not influence the leakage flow rate. With relation to the interactions, the effect of pressure upon leakage flow rate depends on leakage area, being stronger for great leakage areas; the effects of leakage area and pressure on leakage flow rate is more pronounced for longitudinal leakages than for circular leakages. Finally, our results suggest that the equations that predict leakage flow rate in pressurized pipes may need a revision.

Computational fluid dynamics analysis of a modified Savonius rotor and optimization using response surface methodology

2017 ◽  
Vol 41 (5) ◽  
pp. 285-296 ◽  
Author(s):  
Haris Moazam Sheikh ◽  
Zeeshan Shabbir ◽  
Hassan Ahmed ◽  
Muhammad Hamza Waseem ◽  
Muhammad Zubair Sheikh
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Design Of Experiment ◽  
Coefficient Of Performance ◽  
Speed Ratio ◽  
Ansys Fluent ◽  
Computational Fluid Dynamics Analysis ◽  
Parametric Effects

This article aims to present a two-dimensional parametric analysis of a modified Savonius wind turbine using computational fluid dynamics. The effects of three independent parameters of the rotor, namely, shape factor, overlap ratio, and tip speed ratio on turbine performance were studied and then optimized for maximum coefficient of performance using response surface methodology. The rotor performance was analyzed over specific domains of the parameters under study, and three-variable Box-Behnken design was used for design of experiment. The specific parametric combinations as per design of experiment were simulated using ANSYS Fluent®, and the response variable, coefficient of performance (Cp), was calculated. The sliding mesh model was utilized, and the flow was simulated using Shear Stress Transport (SST) k − ω model. The model was validated using past experimental results and found to predict parametric effects accurately. Minitab® and ReliaSoft DOE++® were used to develop regression equation and find the optimum combination of parameters for coefficient of performance over the specified parametric domains using response surface methodology.

Computational Study of Single-Sided Ventilation Through a 3-Dimensional Room With Rounded Edges

2013 ◽  
Author(s):  
A. Idris ◽  
B. P. Huynh
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Wind Speed ◽  
Flow Pattern ◽  
Flow Rate ◽  
Software Package ◽  
Computational Study ◽  
Ventilation Rate ◽  
3 Dimensional ◽  
Computational Fluid Dynamics Cfd

A commercial Computational Fluid Dynamics (CFD) software package is used to investigate numerically a 3-dimensional rectangular-box room with rounded edges. The room has all its window openings located on one wall only. The standard K-ε turbulence model is used. Air’s flow rate and flow pattern are considered in terms of wind speed and the openings’ characteristics, such as their number, location, size and shape. Especially, comparison with ventilation rate corresponding to when the room edges are sharp is made; and thereby the effects of the edges being rounded are examined.

Modeling of High Temperature Gas Flow 3D Distribution in BF Throat Based on the Computational Fluid Dynamics

2015 ◽  
Vol 19 (2) ◽  
pp. 269-276 ◽  
Author(s):  
Jian Qi An ◽  
◽  
Kai Peng ◽  
Wei Hua Cao ◽  
Min Wu ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Gas Flow ◽  
Numerical Solutions ◽  
Flow Distribution ◽  
Three Dimensions ◽  
Cfd Model ◽  
Ansys Fluent ◽  
Proposed Model ◽  
Computational Fluid Dynamics Cfd

This paper aims at building a Computational Fluid Dynamics (CFD) model which can describe the gas flow three dimensions (3D) distribution in blast furnace (BF) throat. Firstly, the boundary conditions are obtained by rebuilding central gas flow shape in BF based on computer graphics. Secondly, the CFD model is built based on turbulent model by analyzing the features of gas flow. Finally, a method which can get the numerical solutions of the model is proposed by using CFD software ANSYS/FLUENT. The proposed model can reflect the changes of the gas flow distribution, and can help to guide the operation of furnace burdening and to ensure the BF stable and smooth production.

Sign in / Sign up

Export Citation Format

Share Document