scholarly journals Controlling the Operation of a Ship’s Electric Powes Supply Using Fuzzy Controllers

2020 ◽  
Vol 222 (3) ◽  
pp. 1-13
Author(s):  
Bogdan Żak ◽  
Stanisław Hożyń
Keyword(s):  
Simulation Model ◽  
Combustion Engine ◽  
Control Process ◽  
Optimal Solution ◽  
Synchronous Generator ◽  
Simulation Research ◽  
Fuzzy Controllers ◽  
Electric Supply ◽  
Selection Of

AbstractThe paper presents dynamical models of controlling voltage and frequency of ship’s electric supply set. The simulation model of synchronous generator, implemented in Matlab/Simulink, was described. For the developed simulation model, developed control systems using fuzzy controllers type P and PD were presented. Simulation research for resistance, inductive and capacitive loads were carried out for these regulators. Sample results of simulation tests are presented in the form of voltage waveforms at the output of the generator and rotational speed of the internal combustion engine for various load conditions. The conducted tests allow to assess the quality of the control process using fuzzy controllers and thus ensure the selection of the optimal solution.

scholarly journals Selection of optimal technical solutions for thermal modernization of school buildings

2020 ◽  
pp. 185-194
Author(s):  
A. Maksymov ◽  
A. Vakhovych
Keyword(s):  
Evaluation System ◽  
Optimal Solution ◽  
Sound Insulation ◽  
Technical Solution ◽  
Environmental Friendliness ◽  
Overall Evaluation ◽  
Two Stages ◽  
Technical Solutions ◽  
Selection Of

Analysis of the most common design and technological solutions used in thermal modernization, showed the impossibility of choosing the optimal solution for a single enclosing structure only by direct assessment of physical, mechanical and technical and economic characteristics.It is proposed to select the optimal design and technological solution in thermal modernization projects from all possible in two stages. At the first stage, it is necessary to discard those solutions, the implementation of which for this type of building is technically impossible or economically or technically impractical. In the second - to assess the system of indicators that comprehensively characterize the design and technological solution.In the article, based on the analysis of literature sources and the authors' own experience in the development and maintenance of thermal modernization projects, a system of criterion evaluation for structural and technological solutions of thermal modernization is developed. The criterion evaluation system for structural and technological solutions of thermal modernization contains a number of indicators that take into account the physicochemical properties of the insulation, environmental friendliness, reliability and stability of the insulation system, technological factors such as maintainability, seasonality, high quality of work due to system technology, ability to sound insulation, economy, artistic efficiency. The method of expert evaluations for each criterion and sub-criterion determines its weight in the overall evaluation. The system of evaluation of technical decisions of thermal modernization of enclosing designs developed by us provides that the estimation on criteria which have subcriteria is defined as the sum of estimations of subcriteria. The evaluation of the criteria is carried out on a five-point scale. The optimal technical solution is the solution that received the highest score on the total.

Identifying Measurement Invariant Item Sets in Cross-Cultural Settings Using an Automated Item Selection Procedure

Methodology ◽  
2018 ◽  
Vol 14 (4) ◽  
pp. 177-188 ◽  
Author(s):  
Martin Schultze ◽  
Michael Eid
Keyword(s):  
Measurement Invariance ◽  
Optimal Solution ◽  
Selection Procedure ◽  
Cross Cultural ◽  
Item Selection ◽  
Ant System ◽  
Item Quality ◽  
Ant System Algorithm ◽  
Selection For ◽  
Selection Of

Abstract. In the construction of scales intended for the use in cross-cultural studies, the selection of items needs to be guided not only by traditional criteria of item quality, but has to take information about the measurement invariance of the scale into account. We present an approach to automated item selection which depicts the process as a combinatorial optimization problem and aims at finding a scale which fulfils predefined target criteria – such as measurement invariance across cultures. The search for an optimal solution is performed using an adaptation of the [Formula: see text] Ant System algorithm. The approach is illustrated using an application to item selection for a personality scale assuming measurement invariance across multiple countries.

ON THE EXPERT’S RIGHT TO BE PRESENT AT LEGAL PROCEEDINGS

2016 ◽  
Vol 15 ◽  
pp. 163-171
Author(s):  
M. G. Shcherbakovskiy
Keyword(s):  
Initial Data ◽  
Legal Proceedings ◽  
Reliable Assessment ◽  
Data Acquiring ◽  
Selection Of

The article discusses the reasonsfor an expert to participate in legal proceedings. The gnoseological reason for that consists of the bad quality of materials subject to examination that renders the examination either completely impossible or compromises objective, reasoned and reliable assessment of the findings. The procedural reason consists ofa proscription for an expert to collect evidence himself or herself. The author investigates into the ways of how an expert can participate in legal proceedings. If the defense invites an expert to participate in the proceedings, then it is recommended that his or her involvement should be in the presence of attesting witnesses and recorded in the protocol. In the course of the legal proceedings an expert has the following tasks: adding initial data, acquiring new initial data, understanding the situation of the incident, acquiring new objects to be studied, including samples for examination. An expert’s participation in legal proceedings differs from the participation of a specialist or an examination on the scene of the incident. The author describes the tasks that an expert solves in the course of legal proceedings, the peculiarities ofan investigation experiment practices, the selection of samples for an examination, inspection, interrogation.

Sensitivity Analysis and Selection of Check Index of Signal Intersection Simulation Model Based on VISSIM

2019 ◽  
Vol 2 (5) ◽  
Author(s):  
Mengda Zhang ◽  
Chenjing Zhou ◽  
Tian-tian Zhang ◽  
Yan Han
Keyword(s):  
Sensitivity Analysis ◽  
Simulation Model ◽  
Optimal Process ◽  
Parameter Calibration ◽  
Index Set ◽  
The Core ◽  
Core Module ◽  
Simulation Parameter ◽  
Simulation Parameters ◽  
Selection Of

Selecting check index quantitatively is the core of the calibration of micro traffic simulation parameters at signal intersection. Five indexes in the node (intersection) module of VISSIM were selected as the check index set. Twelve simulation parameters in the core module were selected as the simulation parameters set. Optimal process of parameter calibration was proposed and model of the intersection of Huangcun west street and Xinghua street in Beijing was built in VISSIM to verify it. The sensitivity analysis between each check index and simulation parameter in their own set was conducted respectively. Sensitive parameter sets of different check indices were obtained and compared. The results show that different indexes have different size of set, and average vehicle delay's is maximum, so it's necessary to select index quantitatively. The results can provide references for scientific selection of the check indexes and improve the study efficiency of parameter calibration.

Implementasi Voip Server Berbasis IPV6 Dengan Raspberry PI

2019 ◽  
Vol 9 (01) ◽  
pp. 47-54
Author(s):  
Rabbai San Arif ◽  
Yuli Fitrisia ◽  
Agus Urip Ari Wibowo
Keyword(s):  
Internet Protocol ◽  
Wireless Transmission ◽  
Raspberry Pi ◽  
Test Results ◽  
Average Delay ◽  
Ipv6 Network ◽  
Ip Network ◽  
Selection Of ◽  
Better Than

Voice over Internet Protocol (VoIP) is a telecommunications technology that is able to pass the communication service in Internet Protocol networks so as to allow communicating between users in an IP network. However VoIP technology still has weakness in the Quality of Service (QoS). VOPI weaknesses is affected by the selection of the physical servers used. In this research, VoIP is configured on Linux operating system with Asterisk as VoIP application server and integrated on a Raspberry Pi by using wired and wireless network as the transmission medium. Because of depletion of IPv4 capacity that can be used on the network, it needs to be applied to VoIP system using the IPv6 network protocol with supports devices. The test results by using a wired transmission medium that has obtained are the average delay is 117.851 ms, jitter is 5.796 ms, packet loss is 0.38%, throughput is 962.861 kbps, 8.33% of CPU usage and 59.33% of memory usage. The analysis shows that the wired transmission media is better than the wireless transmission media and wireless-wired.

DESIGN, SIMULATION AND IMPLEMENTATION MONITORING SYSTEM FOR SYSTEM CONTROL C4 FEEDING PUMP FOR FEED VAPORIZATION IN THE BUTADIENE PLANT

2020 ◽  
Vol 1 (1) ◽  
pp. 31-35
Author(s):  
Fahmi Yunistyawan ◽  
Yunistyawan J Berchmans ◽  
Gembong Baskoro
Keyword(s):  
Motor Control ◽  
Control System ◽  
Field Operator ◽  
System Control ◽  
Variable Speed ◽  
Variable Speed Drive ◽  
Software And Hardware ◽  
Discharge Pressure ◽  
Selection Of

This study implements the auto start control system on an electric motor 3 phase C4Feeding pump when the discharge pressure is low-low (4.3 kg /cm²). The C4 feeding pumpmotor was initially manually operated from the local control station, this was very ineffectiveand inefficient because it still relied on the field operator to operate the pump motor and whenthe plant was in normal operating it is very risk if the field operator late to operate motor then itwill impact to quality of the product, and if the delay time to operate motor is too long then planthave to shut down, therefore improvement is needed in the C4 feeding pump motor controlsystem. In this paper, various types of 3-phase motor control are explained which allow it to beapplied to the C4 feeding pump motor that are on-off, inverter, and variable speed drive andefficient selection of the three systems control of the motor. Software and hardware used in thisthesis work are DCS CENTUM VP Yokogawa.

Thomas More’s Correspondence in a Spanish Ambiance

Moreana ◽  
2002 ◽  
Vol 39 (Number 149) (1) ◽  
pp. 41-60 ◽  
Author(s):  
Eugenio M. Olivares Merino
Keyword(s):  
The Subject ◽  
Selection Of

The recent reprinting of Álvaro de Silva’s 1998 edition of a selection of More’s letters prompts the author to examine the subject of Spanish translations of More, and of de Silva’s general commentary on More’s correspondence and on his relationship to other humanists. The author reflects on aspects of More’s personality as exposed in his letters and uses what he finds as a corrective to several biographical misconceptions. He points out the strengths and weaknesses of de Silva’s work and compares it with that of other translators, particularly Elizabeth Rogers, and notes the particularly Spanish quality of de Silva’s edition.

COMBINATORIAL POLYNOMIALLY COMPUTABLE CHARACTERISTICS OF SUBSTITUTIONS AND THEIR PROPERTIES

2020 ◽  
Vol 7 (2) ◽  
pp. 34-41
Author(s):  
VLADIMIR NIKONOV ◽  
◽  
ANTON ZOBOV ◽  
Keyword(s):  
Mathematical Expectation ◽  
Point Of View ◽  
Small Range ◽  
Computational Point ◽  
Wide Range ◽  
Bijective Function ◽  
The Difference ◽  
Element Base ◽  
Selection Of

The construction and selection of a suitable bijective function, that is, substitution, is now becoming an important applied task, particularly for building block encryption systems. Many articles have suggested using different approaches to determining the quality of substitution, but most of them are highly computationally complex. The solution of this problem will significantly expand the range of methods for constructing and analyzing scheme in information protection systems. The purpose of research is to find easily measurable characteristics of substitutions, allowing to evaluate their quality, and also measures of the proximity of a particular substitutions to a random one, or its distance from it. For this purpose, several characteristics were proposed in this work: difference and polynomial, and their mathematical expectation was found, as well as variance for the difference characteristic. This allows us to make a conclusion about its quality by comparing the result of calculating the characteristic for a particular substitution with the calculated mathematical expectation. From a computational point of view, the thesises of the article are of exceptional interest due to the simplicity of the algorithm for quantifying the quality of bijective function substitutions. By its nature, the operation of calculating the difference characteristic carries out a simple summation of integer terms in a fixed and small range. Such an operation, both in the modern and in the prospective element base, is embedded in the logic of a wide range of functional elements, especially when implementing computational actions in the optical range, or on other carriers related to the field of nanotechnology.

Spatial Autocorrelation in the Study of Neighbourhoods towards Smart Cities: Empirical Evidence from Kerman, Iran

2012 ◽  
Vol 9 (2) ◽  
pp. 1
Author(s):  
Asra Hosseini
Keyword(s):  
Spatial Autocorrelation ◽  
Urban Areas ◽  
Smart Cities ◽  
Moran’S I ◽  
Moran's I ◽  
Urban Planner ◽  
Universal Feature ◽  
Autocorrelation Method ◽  
Selection Of

From earliest cities to the present, spatial division into residential zones and neighbourhoods is the universal feature of urban areas. This study explored issue of measuring neighbourhoods through spatial autocorrelation method based on Moran's I index in respect of achieving to best neighbourhoods' model for forming cities smarter. The research carried out by selection of 35 neighbourhoods only within central part of traditional city of Kerman in Iran. The results illustrate, 75% of neighbourhoods' area in the inner city of Kerman had clustered pattern, and it shows reduction in Moran's index is associated with disproportional distribution of density and increasing in Moran's I and Z-score have monotonic relation with more dense areas and clustered pattern. It may be more efficient for urban planner to focus on spatial autocorrelation to foster neighbourhood cohesion rather than emphasis on suburban area. It is recommended characteristics of historic neighbourhoods can be successfully linked to redevelopment plans toward making city smarter, and also people's quality of life can be related to the way that neighbourhoods' patterns are defined. 

Sign in / Sign up

Export Citation Format

Share Document