scholarly journals Investigation of Local Scour around L-Shape Submerged Groynes in Clearwater Conditions

2021 ◽  
Vol 28 (3) ◽  
pp. 159-169
Author(s):  
Saleh Issa Khassaf ◽  
Budoor Mohammed Rashak

Submerged Groynes are low profile linear structures that are generally located on the outside bank to form Groynes fields and prevent the erosion of stream banks by redirecting high-velocity flow away from the bank. This research was studied in detail through two major stages. The first stage of the study is based on laboratory experiments to measure the development of local scour around L-shape submerged Groyne with the time, and special attention is given to the effects of different hydraulic and geometric parameters on local scour. Also; maps were drawn showing contour lines that represented the bed levels for maximum scour depth after reaching the equilibrium case. The result showed that a decrease in the scour depth ratio due to the increasing submerged ratio, and the number of Groynes. While the scour hole geometry will increase with the Froude number, flow intensity, and the spacing between Groynes, the decreasing percentage in the scour hole was measured to be about (4.3) % and (4.4) % for decreasing the spacing between Groynes from (2Lg) to (1.5Lg). Besides, it was range about (11.1) % and (14.0) % when reducing the spacing from (1.5Lg) to (Lg) under the same value of maximum Froude number. The second stage of the study is based on experimental results. A new formula was developed by using statistical analysis and it was found that a good determination coefficient.

2018 ◽  
Vol 13 (2) ◽  
pp. 110-120 ◽  
Author(s):  
Ibtesam Abudallah Habib ◽  
Wan Hanna Melini Wan Mohtar ◽  
Atef Elsaiad ◽  
Ahmed El-Shafie

This study investigates the performance nose-angle piers as countermeasures for local scour reduction around piers. Four nose angles were studied, i.e., 90°, 70°, 60° and 45° and tested in a laboratory. The sediment size was fixed at 0.39 mm whereas the flow angle of attack (or skew angle) was varied at four angles, i.e., skew angles, i.e., 0°, 10°, 20° and 30°. Scour reduction was clear when decreasing nose angles and reached maximum when the nose angle is 45°. Increasing the flow velocity and skew angle was subsequently increasing the scour profile, both in vertical and transversal directions. However, the efficiency of nose angle piers was only high at low Froude number less than 0.40 where higher Froude number gives minimal changes in the maximum scour depth reduction. At a higher skew angle, although showed promising maximum scour depth reduction, the increasing pier projected width resulted in the increase of transversal lengths.


2014 ◽  
Vol 9 (3) ◽  
pp. 331-343 ◽  
Author(s):  
N. Ahmad ◽  
T. Mohamed ◽  
F. H. Ali ◽  
B. Yusuf

Laboratory data for local scour depth regarding the size of wide piers are presented. Clear water scour tests were performed for various pier widths (0.06, 0.076, 0.102, 0.14 and 0.165 m), two types of pier shapes (circular and rectangular) and two types of uniform cohesionless bed sediment (d50 = 0.23 and d50 = 0.80 mm). New data are presented and used to demonstrate the effects of pier width, pier shape and sediment size on scour depth. The influence of equilibrium time (te) on scouring processes is also discussed. Equilibrium scour depths were found to decrease with increasing values of b/d50. The temporal development of equilibrium local scour depth with new laboratory data is demonstrated for flow intensity V/Vc = 0.95. On the other hand, the results of scour mechanism have shown a significant relationship between normalized volume of scoured and deposited with pier width, b. The experimental data obtained in this study and data available from the literature for wide piers are used to evaluate predictions of existing methods.


2014 ◽  
Vol 641-642 ◽  
pp. 271-274
Author(s):  
Qiang Ying

This passage introduces the formation process of scour hole, analyzes the main factors contributed to the local scour hole’s depth and classifies today’s calculation methods of scour depth into three categories. Then, given the conditions where those methods can be applied and drawbacks of those methods, this article also recommends some suggested formula in calculation.


Water ◽  
2019 ◽  
Vol 11 (5) ◽  
pp. 1041 ◽  
Author(s):  
Sung Won Park ◽  
Jin Hwan Hwang ◽  
Jungkyu Ahn

Local scour at the downstream of the river bed protection is one of the most important parameters for the design criteria and sustainable management of the hydraulic structures. Previously, various researches on its process in the equilibrium state have been suggested with experimental and numerical approaches. In this study, relatively long-term laboratory experiments of local scouring at the downstream of fixed bed in an open channel were conducted with mono-granular sediment bed and analyzed about maximum scour depth and its temporal development. In particular, we conducted experiments with relatively low Froude number (less than 0.5) and their duration of tests was exceeded over 700 hours. We modified the relationship between the dimensionless time and length scales of the maximum scour depth of the local scour hole based on the turbulent shear layer thickness. A new functional relationship between dominant factors and the maximum scour depth in the equilibrium state were suggested and compared with previously suggested formula. Also, from the results by nonlinear regression, Froude number was founded as a dominant factor on the prediction of equilibrium maximum scour depth.


2019 ◽  
Vol 8 (1) ◽  
pp. 4 ◽  
Author(s):  
Bingchen Liang ◽  
Shengtao Du ◽  
Xinying Pan ◽  
Libang Zhang

Scour induced by currents is one of the main causes of the bridge failure in rivers. Fundamental knowledge and mechanisms on scour processes due to currents are often taken as a basis for scour studies, which are the focus of this review. Scour development induced by waves and in combined wave–current conditions are also briefly discussed. For the design of structure foundations, the maximum scour depths need to be estimated. The mechanisms of local scour and predictions of maximum local scour depths have been studied extensively for many years. Despite the complexity of the scour process, a lot of satisfying results and progresses have been achieved by many investigators. In order to get a comprehensive review of local scour for vertical piles, major progresses made by researchers are summarized in this review. In particular, maximum scour depth influencing factors including flow intensity, sediments, pile parameters and time are analyzed with experimental data. A few empirical equations referring to temporary scour depth and maximum scour depth were classified with their expressing forms. Finally, conclusions and future research directions are addressed.


Water ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1462
Author(s):  
Chung-Ta Liao ◽  
Keh-Chia Yeh ◽  
Yin-Chi Lan ◽  
Ren-Kai Jhong ◽  
Yafei Jia

Local scour is a common threat to structures such as bridge piers, abutments, and dikes that are constructed on natural rivers. To reduce the risk of foundation failure, the understanding of local scour phenomenon around hydraulic structures is important. The well-predicted scour depth can be used as a reference for structural foundation design and river management. Numerical simulation is relatively efficient at studying these issues. Currently, two-dimensional (2D) mobile-bed models are widely used for river engineering. However, a common 2D model is inadequate for solving the three-dimensional (3D) flow field and local scour phenomenon because of the depth-averaged hypothesis. This causes the predicted scour depth to often be underestimated. In this study, a repose angle formula and bed geometry adjustment mechanism are integrated into a 2D mobile-bed model to improve the numerical simulation of local scour holes around structures. Comparison of the calculated and measured bed variation data reveals that a numerical model involving the improvement technique can predict the geometry of a local scour hole around spur dikes with reasonable accuracy and reliability.


2014 ◽  
Vol 16 (5) ◽  
pp. 1210-1226 ◽  
Author(s):  
Sherong Zhang ◽  
Bohui Pang ◽  
Gaohui Wang

The prediction of the maximum depth of the scour hole formed downstream of overflow dams is critical in determining the safety of hydraulic structures. Most of the conventional formulae are not able to consider complex hydraulic and morphologic conditions. A new formula for estimating the maximum depth of the scour hole based on computational fluid dynamics (CFD), which can be used to simulate the complicated phenomenon, is proposed. The relationship between the maximum velocity in numerical simulations and the maximum scour depth is reflected in this formula, which is established using the Levenberg–Marquardt (LM) algorithm. The validity of this proposed formula is discussed by comparing this formula with three other conventional formulae. The prediction formula based on CFD is applied to the Wuqiangxi Dam, and the absolute deviation of the predicted maximum scour depth (35.44 m) from the measured depth (36.00 m) is 0.56 m.


2006 ◽  
Vol 33 (7) ◽  
pp. 902-911 ◽  
Author(s):  
Jueyi Sui ◽  
Daxian Fang ◽  
Bryan W Karney

Based on a series of experiments, this paper explores the influence of a 90° change in flow direction on local scouring. The influence on local scour patterns due to hydraulic parameters such as the Froude number, the slope of the protection wall, the width of the protection apron along the outside wall of the downstream section, and the grain size of the channel bed material is examined. Protection-wall slopes ranging from 1:0.5 to 1:4 (vertical to horizontal) were investigated, as were different widths of the protection apron; the goal was to ascertain the role of these variables in local scour patterns in the vicinity of the bend. The factors affecting local scour depth are related through empirical equations to key hydraulic variables, the slope of the protection wall, and the width of the protection apron.Key words: bent flume, channel erosion, Froude number, scour depth, slope of protection wall (SPW), width of protection apron (WPA).


2021 ◽  
Vol 69 (3) ◽  
pp. 275-287
Author(s):  
Jun Wang ◽  
Zhixing Hou ◽  
Hongjian Sun ◽  
Bihe Fang ◽  
Jueyi Sui ◽  
...  

Abstract The appearance of an ice jam in a river crucially distorts local hydrodynamic conditions including water level, flow velocity, riverbed form and local scour processes. Laboratory experiments are used for the first time here to study ice-induced scour processes near a bridge pier. Results show that with an ice sheet cover the scour hole depth around a bridge is increased by about 10% compared to under equivalent open flow conditions. More dramatically, ice-jammed flows induce both greater scour depths and scour variability, with the maximum scour depth under an ice-jammed flow as much as 200% greater than under equivalent open flow conditions. Under an ice-jammed condition, both the maximum depth and length of scour holes around a bridge pier increase with the flow velocity while the maximum scour hole depth increases with ice-jam thickness. Also, quite naturally, the height of the resulting deposition dune downstream of a scour hole responds to flow velocity and ice jam thickness. Using the laboratory data under ice-jammed conditions, predictive relationships are derived between the flow’s Froude number and both the dimensionless maximum scour depth and the dimensionless maximum scour length.


Sign in / Sign up

Export Citation Format

Share Document