scholarly journals Simulation and Assessment of Groundwater for Domestic and Irrigation Uses

2019 ◽  
Vol 5 (9) ◽  
pp. 1877-1892 ◽  
Author(s):  
Majed Rodhan Hussain ◽  
Basim Sh. Abed
Keyword(s):  
Cross Sections ◽  
Three Dimensional ◽  
Water Quality Assessment ◽  
Alluvial Fan ◽  
Water Levels ◽  
Specific Yield ◽  
Annual Rainfall ◽  
Steady State Condition ◽  
Groundwater Samples ◽  
One Year

The alluvial fan of Mandali located between latitude 30˚45’00” N longitude 45˚30’00” E in east of Diyala Governorate, Iraq. Thirty-five wells were identified in the study area with average depth of 84 m and estimated area of 21550 ha. A three-dimensional conceptual model was prepared by using GMS program. From wells cross sections, four geological layers have been identified. The hydraulic conductivity of these layers was calculated for steady state condition, where the water levels for nine wells distributed over the study area were observed at same time. Afterward, PEST facility in the GMS was used to estimate the aquifer hydraulic characteristics. Other characteristics such as storage coefficient and specific yield have been determined from one year field observations that were collected by General Authority of Groundwater, Diyala Governorate. Also, the observations were used for calibration of unsteady state model. Then wells were hypothetically redistributed and increased to 103 wells, assuming a distance of 1500 m between the wells, a well productivity rate of were 7 l/s, annual rainfall rate was used for recharging. Three different wells operating times were suggested and these 6, 12, and 18 hr/day with total discharge of 150, 300, 450 m3/day and maximum drawdown of 7, 11, and 20 m respectively. For water quality assessment, the collected groundwater samples were analysed at the laboratory.  Results showed that the TDS in all wells was ranged from 1000-3000 mg/l but TDS in well number 18 was exceeded 3000 mg/l which indicate that the groundwater in this well is not recommended to be used for irrigation. According to Iraqi standard for drink (IQS 2009), it can be used for drinking if saline treatment units were provided.

scholarly journals Seepage Behavior of Earth Dams Considering Rainfall Effects

2018 ◽  
Vol 2018 ◽  
pp. 1-9
Author(s):  
Jong-Wook Lee ◽  
Jiseong Kim ◽  
Gi-Chun Kang
Keyword(s):  
Monsoon Season ◽  
Seepage Flow ◽  
Water Levels ◽  
Annual Rainfall ◽  
Seepage Water ◽  
Earth Dams ◽  
Reservoir Water ◽  
Seepage Rate ◽  
Steady State Condition ◽  
Rock Fill

More than 60% of annual rainfall in Korea is concentrated during the monsoon season from June to August because of the climate characteristics of East Asia. In general, reservoir water levels sharply rise during this period and rock-fill dams are exposed to various types of damages such as soil erosion and piping related to seepage problems. However, the detection of seepage problems is generally more difficult because rainfall directly flows into a V-notch weir according to a downstream shell in which seepage rates can be measured downstream. In this paper, rainfall is filtered out from the measured seepage rates to evaluate the effects of rainfall by using a digital filtering method for two large rock-fill dams (Dams A and B). Seepage behavior for these two large rock-fill dams was estimated as a steady-state condition. It has been proven that with the application of a digital filter which filters out rainfall-induced infiltration into a downstream shell from a measured seepage flow would make analyzing the seepage behavior of dams more effective. This also shows that consideration for any rainfall effect on the seepage behavior of earth dams is very important. The seepage rate of Dam A was not significantly affected by rainfall because the seepage water was collected inside the dam body and was transferred to a V-notch weir located downstream from the dam through a steel pipe. On the contrary, the seepage rate of Dam B was greatly influenced by rainfall in the rainy season. Also, the permeability of the core zones for Dams A and B was estimated at 8.5 × 10−5 cm/sec and 2.7 × 10−5 cm/sec, respectively, by a simplified method.

Using groundwater levels and Specific Yield to Estimate the Recharge, South of Erbil, Kurdistan Region, Iraq

2018 ◽  
Vol 7 (4) ◽  
pp. 191
Author(s):  
Sherwan Sh. Qurtas
Keyword(s):  
Unconfined Aquifer ◽  
Middle Part ◽  
Water Levels ◽  
Specific Yield ◽  
Aquifer System ◽  
Groundwater Levels ◽  
Monitoring Wells ◽  
Water Table Fluctuation Method ◽  
Recharge Estimation ◽  
Fluctuation Method

Recharge estimation accurately is crucial to proper groundwater resource management, for the groundwater is dynamic and replenished natural resource. Usually recharge estimation depends on the; the water balance, water levels, and precipitation. This paper is studying the south-middle part of Erbil basin, with the majority of Quaternary sediments, the unconfined aquifer system is dominant, and the unsaturated zone is ranging from 15 to 50 meters, which groundwater levels response is moderate. The purpose of this study is quantification the natural recharge from precipitation. The water table fluctuation method is applied; using groundwater levels data of selected monitoring wells, neighboring meteorological station of the wells, and the specific yield of the aquifers. This method is widely used for its simplicity, scientific, realistic, and direct measurement. The accuracy depends on the how much the determination of specific yield is accurate, accuracy of the data, and the extrapolations of recession of groundwater levels curves of no rain periods. The normal annual precipitation there is 420 mm, the average recharge is 89 mm, and the average specific yield is around 0.03. The data of one water year of 2009 and 2010 has taken for some technical and accuracy reasons.

Geological Field Sketches and Illustrations

2019 ◽  
Author(s):  
Matthew J. Genge
Keyword(s):  
Cross Sections ◽  
Earth Science ◽  
Three Dimensional ◽  
Worked Examples ◽  
Scientific Publications ◽  
Thin Sections ◽  
Geological Features ◽  
Different Types ◽  
The Subject

Drawings, illustrations, and field sketches play an important role in Earth Science since they are used to record field observations, develop interpretations, and communicate results in reports and scientific publications. Drawing geology in the field furthermore facilitates observation and maximizes the value of fieldwork. Every geologist, whether a student, academic, professional, or amateur enthusiast, will benefit from the ability to draw geological features accurately. This book describes how and what to draw in geology. Essential drawing techniques, together with practical advice in creating high quality diagrams, are described the opening chapters. How to draw different types of geology, including faults, folds, metamorphic rocks, sedimentary rocks, igneous rocks, and fossils, are the subjects of separate chapters, and include descriptions of what are the important features to draw and describe. Different types of sketch, such as drawings of three-dimensional outcrops, landscapes, thin-sections, and hand-specimens of rocks, crystals, and minerals, are discussed. The methods used to create technical diagrams such as geological maps and cross-sections are also covered. Finally, modern techniques in the acquisition and recording of field data, including photogrammetry and aerial surveys, and digital methods of illustration, are the subject of the final chapter of the book. Throughout, worked examples of field sketches and illustrations are provided as well as descriptions of the common mistakes to be avoided.

scholarly journals Thermo-Hydraulic Performance of U-Tube Borehole Heat Exchanger with Different Cross-Sections

2021 ◽  
Vol 13 (6) ◽  
pp. 3255
Author(s):  
Aizhao Zhou ◽  
Xianwen Huang ◽  
Wei Wang ◽  
Pengming Jiang ◽  
Xinwei Li
Keyword(s):  
Heat Transfer ◽  
Heat Exchange ◽  
Heat Resistance ◽  
Cross Sections ◽  
Three Dimensional ◽  
Thermal Response ◽  
Transfer Efficiency ◽  
Cross Sectional ◽  
Heat Transfer Efficiency ◽  
Oval Tube

For reducing the initial GSHP investment, the heat transfer efficiency of the borehole heat exchange (BHE) system can be enhanced to reduce the number or depth of drilling. This paper proposes a novel and simple BHE design by changing the cross-sectional shape of the U-tube to increase the heat transfer efficiency of BHEs. Specifically, in this study, we (1) verified the reliability of the three-dimensional numerical model based on the thermal response test (TRT) and (2) compared the inlet and outlet temperatures of the different U-tubes at 48 h under the premise of constant leg distance and fluid area. Referent to the circular tube, the increases in the heat exchange efficiencies of the curved oval tube, flat oval tube, semicircle tube, and sector tube were 13.0%, 19.1%, 9.4%, and 14.8%, respectively. (3) The heat flux heterogeneity of the tubes on the inlet and outlet sides of the BHE, in decreasing order, is flat oval, semicircle, curved oval, sector, and circle shapes. (4) The temperature heterogeneity of the borehole wall in the BHE in decreasing order is circle, sector, curved oval, flat oval, and semicircle shapes. (5) Under the premise of maximum leg distance, referent to the heat resistance of the tube with a circle shape at 48 h, the heat exchange efficiency of the curved oval, flat oval, semicircle, and sector tubes increased 12.6%, 17.7%, 10.3%, and 7.8%, respectively. (6) We found that the adjustments of the leg distance and the tube shape affect the heat resistance by about 25% and 12%, respectively. (7) The flat-oval-shaped tube at the maximum leg distance was found to be the best tube design for BHEs.

Lake and inland dunes as interconnected Systems: The story of Lake Tresssee and an adjacent dune field (Schleswig-Holstein, North Germany)

The Holocene ◽  
2020 ◽  
pp. 095968362098168
Author(s):  
Christian Stolz ◽  
Magdalena Suchora ◽  
Irena A Pidek ◽  
Alexander Fülling
Keyword(s):  
Water Level ◽  
Bronze Age ◽  
Environmental Changes ◽  
High Water ◽  
Alluvial Fan ◽  
Water Levels ◽  
Lake Area ◽  
Dune Field ◽  
The North ◽  
Sand Drift

The specific aim of the study was to investigate how four adjacent geomorphological systems – a lake, a dune field, a small alluvial fan and a slope system – responded to the same impacts. Lake Tresssee is a shallow lake in the North of Germany (Schleswig-Holstein). During the Holocene, the lake’s water surface declined drastically, predominately as a consequence of human impact. The adjacent inland dune field shows several traces of former sand drift events. Using 30 new radiocarbon ages and the results of 16 OSL samples, this study aims to create a new timeline tracing the interaction between lake and dunes, as well, as how both the lake and the dunes reacted to environmental changes. The water level of the lake is presumed to have peaked during the period before the Younger Dryas (YD; start at 10.73 ka BC). After the Boreal period (OSL age 8050 ± 690 BC) the level must have undergone fluctuations triggered by climatic events and the first human influences. The last demonstrable high water level was during the Late Bronze Age (1003–844 cal. BC). The first to the 9th century AD saw slightly shrinking water levels, and more significant ones thereafter. In the 19th century, the lake area was artificially reduced to a minimum by the human population. In the dunes, a total of seven different phases of sand drift were demonstrated for the last 13,000 years. It is one of the most precisely dated inland-dune chronologies of Central Europe. The small alluvial fan took shape mainly between the 13th and 17th centuries AD. After 1700 cal. BC (Middle Bronze Age), and again during the sixth and seventh centuries AD, we find enhanced slope activity with the formation of Holocene colluvia.

Three-dimensional bluff evolution in response to seasonal fluctuations in Great Lakes water levels

2020 ◽  
Vol 46 (6) ◽  
pp. 1533-1543 ◽  
Author(s):  
C.A. Volpano ◽  
L.K. Zoet ◽  
J.E. Rawling ◽  
E.J. Theuerkauf ◽  
R. Krueger
Keyword(s):  
Great Lakes ◽  
Three Dimensional ◽  
Water Levels ◽  
Seasonal Fluctuations

scholarly journals Computer-aided design of multi-purpose steel headframes for mines with a new technical level

2020 ◽  
Vol 174 ◽  
pp. 01048
Author(s):  
Elena Kassikhina ◽  
Vladimir Pershin ◽  
Nina Rusakova
Keyword(s):  
Cross Sections ◽  
Computer Aided Design ◽  
Information Technologies ◽  
Three Dimensional ◽  
Numerical Control ◽  
Technical Level ◽  
Resource Saving ◽  
Existing Structures ◽  
Set Up ◽  
Aided Design

The existing structures of the steel sinking headgear and permanent headframe do not meet the requirements of resource saving (metal consumption and manpower input at installation), and the present methods of the headframe designing do not fully reflect recent possibilities of applying of the advanced information technologies. Technical level of the modern software makes it possible for designers to set up multiple numerical experiments to create a computer simulation that allows solving the problem without field and laboratory experiments, and therefore without special costs. In this regard, a mathematical simulation has been developed and based on it, software to select cross-sections of multi- purpose steel headframe elements and to calculate proper weight of its metal structures depending on the characteristics and hoisting equipment. A headframe drawing is displayed, as the results of the software work, including list of elements, obtained optimal hoisting equipment in accordance with the initial data. The software allows speeding up graphic work and reducing manpower input on calculations and paper work. The software allows developing a three-dimensional image of the structure and its functional blocks, based on the obtained initial parameters, as well as developing control software for units with numerical control (NC) in order to manufacture multi-purpose headframes.

Sign in / Sign up

Export Citation Format

Share Document