scholarly journals Pemilahan Sampah Plastik Untuk Mendukung Program Zero Waste Pada Pusat Daur Ulang Sampah Bajang Peripih Doro, Pringgarata, Lombok Tengah Tahun 2021

2021 ◽  
Vol 4 (4) ◽  
pp. 402-409
Author(s):  
Dian W. Kurniawidi ◽  
Teguh Ardianto ◽  
Syamsuddin ◽  
Siti Alaa' ◽  
Amrul Ikhsan ◽  
...  

Sampah plastik merupakan salah satu masalah serius di seluruh wilayah di Indonesia, apalagi pulau Lombok karena gugus pulau yang kecil. Dari berbagai jenis sampah, sampah plastik merupakan sampah non-organik yang paling banyak dihasilkan dan memiliki berbagai dampak bagi kesehatan dan lingkungan. Usaha mengurangi sampah dengan membuat Tempat Pembuangan Akhir, Tempat Pembuangan Sampah, dan Bank Sampah nampaknya perlu didukung oleh kesadaran masyarakat untuk mengurangi penggunaan sampah dan memilah sampah sehingga dapat mengurangi beban pengelolaan sampah yang dilakukan oleh pemerintah daerah. Pada kegiatan pengabdian kepada masyarakat kali ini dilakukan kegiatan pembimbingan, praktek lapangan dan sosialisasi kepada masyarakat ilmiah, mahasiswa dan alumni program studi pendidikan Fisika di Pusat Daur Ulang Bajang Peripih Doro di dusun Murbaya Desa Pringgarata Lombok Tengah yang telah melakukan kegiatan dengan hasil yaitu pembuatan paving block dari limbah plastik, pembuatan biofuel dari sampah plastik serta pembuatan batako. Limbah plastik yang digunakan didapatkan dari tempat pembuangan sampah masyarakat setempat, dengan memilih jenis limbah plastik low density polyethylene (LDPE), PET (polyethylene terepthalete), dan HDPE (high density polyethylene). Plastik jenis ini biasanya digunakan untuk membuat kantong plastik, plastik lembaran, bungkus makanan ringan, bungkus roti maupun kemasan-kemasan sejenisnya. Pembelajaran yang diperoleh menghasilkan uji coba sampel dengan nilai kuat tekan pada campuran limbah plastik 75% sebesar 8,2 MPa, dan penyerapan air sebesar 0,3109%. Sedangkan untuk pengujian bahan bakar diperoleh bahan bakar yang massa jenisnya 0,708 g/ml. Kelemahannya bahan bakar ini tidak ditemukannya senyawa oksigen yang dapat menyebabkan korosi pada mesin. Sehingga alternatif penggunaannya adalah pada industri pembakaran batu bata atau industri pengeringan tembakau.

Author(s):  
S. JIPA ◽  
R. SETNESCU ◽  
T. SETNESCU ◽  
C. PODINA ◽  
J. MIHALCEA

The effectiveness of different phenolic antioxidants on high-density polyethylene (HDPE) and low-density polyethylene (LDPE) has been studied by the Isothermal chemiluminescence method. The decreasing order of the antioxidant efficiency for these polymers Is as follows: lrganox 1010 >> Etanox 330 > lrganox 1076 (Hostanox 016) > Topanol OC


2020 ◽  
Vol 10 ◽  
pp. 48-55
Author(s):  
H. V. Allakhverdiyeva ◽  
◽  
N. T. Kakhramanov ◽  
I. I. Ismayilov ◽  
◽  
...  

The paper presents the results of a study of the effect of aluminum content on the physic-mechanical properties of composites based on high density polyethylene and low density polyethylene. The properties of metal-filled composites, such as ultimate tensile stress, elongation at break, elastic module, melt flow rate, and heat resistance, were studied. According to the data obtained, the loading of aluminum into the composition of low density polyethylene contributes to a monotonic increase in the ultimate tensile stress and the elastic module. When aluminum is loading into the composition of high density polyethylene, on the contrary, a natural decrease in the ultimate tensile stress and elongation at break of the composites is observed. It is shown that when using a compatibilizer, which is polyethylene modified with maleic anhydride, a significant increase in the ultimate tensile stress of high-density polyethylene composites is observed. A schematic representation of the structure of composites with an interpretation of the probable mechanism of hardening of the material in the presence of a compatibilizer is given. It is shown that the crystallinity of the initial polyethylene has a significant effect on the hardening effect of composites. Electron microscopic micrographs of the structure of a filled composite without and with compatibilizer are given. A comparative assessment shows that in the presence of a compatibilizer, aluminum particles are in the bulk of the polymer matrix, i.e. are not in an isolated state. It is assumed that HDPE macrochains free of maleic anhydride (MA) are involved in the formation of crystalline formations, and small sections of macrosegments containing polar groups of MA are concentrated mainly in amorphous regions and in defects in crystalline structures in the form of passage chains. The concentration of PEMA macrosegments containing MA in the narrow amorphous space of HDPE favorably affects the increase in the adhesive forces of interaction on the surface of aluminum particles, which affects the preservation of the ultimate tensile stress at a relatively high level over a wide range of aluminum concentrations.


Sign in / Sign up

Export Citation Format

Share Document