scholarly journals Perancangan Bilah Turbin Angin Jenis Taperless Untuk Pesisir Pantai Utara Jawa Barat Menggunakan Perangkat Lunak QBlade

2021 ◽  
Vol 14 (2) ◽  
pp. 118-124
Author(s):  
Shinta Dwi Oktaviani ◽  
Reza Setiawan ◽  
Farradina Choria Suci
Keyword(s):  
Renewable Energy ◽  
Wind Turbine ◽  
Turbine Blade ◽  
Renewable Energy Sources ◽  
Environmentally Friendly ◽  
Wind Turbine Blade ◽  
Power Coefficient ◽  
Horizontal Wind ◽  
Energy Sources ◽  
Literature Study

Energy needs in Indonesia continue to increase, while the availability of non-renewable energy sources is decreasing and is exacerbated by the increasing use of fuels that are not environmentally friendly, so efforts are needed to find alternative uses of renewable energy that are renewable and environmentally friendly. The Cirebon coast has good wind conditions which can be used to create renewable energy sources through the wind. This study aims to utilize the energy that is already available by designing a horizontal wind turbine blade. The method used starts from literature study, selecting airfoils, analyzing data, selecting the best airfoils, analyzing the best airfoils and ending with design drawings. The initial data used as the initial design is the Cirebon City wind data which has the highest average wind speed of 9 m/s. This study designed a horizontal wind turbine blade using QBlade Software with 3 types of NACA, NACA 4415, 6412 and 6415. NACA 6415 has a power coefficient of 0.40%, the highest coefficient is then obtained NACA 6412 with a coefficient of 0.41%, and The highest power coefficient was obtained by NACA 4415 with a coefficient of 44%

Aerodynamic Comparison of Straight Edge and Swept Edge Wind Turbine Blade

2008 ◽  
Author(s):  
R. S. Amano ◽  
Ryan J. Malloy
Keyword(s):  
Renewable Energy ◽  
Wind Energy ◽  
Wind Turbine ◽  
Turbine Blade ◽  
Low Cost ◽  
Renewable Energy Sources ◽  
Optimization Technique ◽  
Wind Turbine Blade ◽  
Direct Result ◽  
Low Wind Speed

Recently there has been an increase in the demand for the utilization of clean renewable energy sources. This is a direct result of a rise in oil prices and an increased awareness of human induced climate change. Wind energy has been shown to be one of the most promising sources of renewable energy. With current technology, the low cost of wind energy is competitive with more conventional sources of energy such as coal. This however is only true in areas of high wind density. These areas are not as abundant and therefore the number of profitable sites is limited. This paper explores the possibility increasing the number of profitable sites by optimizing wind turbine blade design for low wind speed areas. The two methods of optimization that are investigated are first, optimizing the angle of attack and chord length for a given airfoil cross section at different positions along the blade and second implementing a swept blade profile. The torque generated from a blade using only the first optimization technique is compared to that generated from a blade using both techniques as well as that generated by NTK500/41 turbine using LM19.1 blades. Performance will be investigated using the CFD solver FLUENT.

Wind Turbine Aerodynamic Braking System Analysis Using Chord Wise Spacing

2015 ◽  
Vol 787 ◽  
pp. 217-221 ◽  
Author(s):  
B. Navin Kumar ◽  
K.M. Parammasivam
Keyword(s):  
Renewable Energy ◽  
Wind Turbine ◽  
Wind Velocity ◽  
Turbine Blade ◽  
Wind Turbines ◽  
Renewable Energy Sources ◽  
Energy Resource ◽  
Braking System ◽  
Extreme Wind ◽  
Wind Potential

Wind energy is one of the most significant renewable energy sources in the world. It is the only promising renewable energy resource that only can satisfy the nation’s energy requirements over the growing demand for electricity. Wind turbines have been installed all over the wind potential areas to generate electricity. The wind turbines are designed to operate at a rated wind velocity. When the wind turbines are exposed to extreme wind velocities such as storm or hurricane, the wind turbine rotates at a higher speed that affects the structural stability of the entire system and may topple the system. Mechanical braking systems and Aerodynamic braking systems have been currently used to control the over speeding of the wind turbine at extreme wind velocity. As a novel approach, it is attempted to control the over speeding of the wind turbine by aerodynamic braking system by providing the chord wise spacing (opening). The turbine blade with chord wise spacing alters the pressure distribution over the turbine blade that brings down the rotational speed of the wind turbine within the allowable limit. In this approach, the over speeding of the wind turbine blades are effectively controlled without affecting the power production. In this paper the different parameters of the chord wise spacing such as position of the spacing, shape of the spacing, width of the spacing and impact on power generation are analyzed and the spacing parameters are experimentally optimized.

scholarly journals Design Optimization of a Multi-Megawatt Wind Turbine Blade with the NPU-MWA Airfoil Family

Energies ◽  
2019 ◽  
Vol 12 (17) ◽  
pp. 3330 ◽  
Author(s):  
Jianhua Xu ◽  
Zhonghua Han ◽  
Xiaochao Yan ◽  
Wenping Song
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Weight Reduction ◽  
Stokes Equations ◽  
Lift Coefficient ◽  
Turbine Blades ◽  
Aerodynamic Performance ◽  
Wind Turbine Blade ◽  
Structural Performance ◽  
Power Coefficient

A new airfoil family, called NPU-MWA (Northwestern Polytechnical University Multi-megawatt Wind-turbine A-series) airfoils, was designed to improve both aerodynamic and structural performance, with the outboard airfoils being designed at high design lift coefficient and high Reynolds number, and the inboard airfoils being designed as flat-back airfoils. This article aims to design a multi-megawatt wind turbine blade in order to demonstrate the advantages of the NPU-MWA airfoils in improving wind energy capturing and structural weight reduction. The distributions of chord length and twist angle for a 5 MW wind turbine blade are optimized by a Kriging surrogate model-based optimizer, with aerodynamic performance being evaluated by blade element-momentum theory. The Reynolds-averaged Navier–Stokes equations solver was used to validate the improvement in aerodynamic performance. Results show that compared with an existing NREL (National Renewable Energy Laboratory) 5 MW blade, the maximum power coefficient of the optimized NPU 5 MW blade is larger, and the chord lengths at all span-wise sections are dramatically smaller, resulting in a significant structural weight reduction (9%). It is shown that the NPU-MWA airfoils feature excellent aerodynamic and structural performance for the design of multi-megawatt wind turbine blades.

Modelling and Control of the Hydraulically Actuated Horizontal Axis Wind Turbine Pitch System

2019 ◽  
Author(s):  
P. Venkaiah ◽  
B. K. Sarkar
Keyword(s):  
Renewable Energy ◽  
Wind Energy ◽  
Wind Turbine ◽  
Wind Power ◽  
Pid Controller ◽  
Renewable Energy Sources ◽  
Horizontal Axis ◽  
Energy Sources ◽  
Horizontal Axis Wind Turbine ◽  
The World

Abstract The advantages of renewable energy sources are available freely in nature, inexhaustible, produce either no or little pollution and low gestation period. Among all renewable energy sources, wind energy has become one of the leading resources for power production in the world as well as in the India. According to WWEA, the wind turbine installation capacity in the world has been reached over 539.291GW by the end of 2017. The entire wind power installed capacity by the end of 2017 covers more than 5% of global demand of electricity. In India, the present wind power installation capacity on October, 2017 was over 32.7GW and wind energy contribution is 55% of the total renewable energy capacity in the country. Inspite of having sharp growth rate in wind in India, only a fraction of wind energy has been tapped until now out of 302 GW wind potential which is available above 100 m height on shore. Practical horizontal axis wind turbine converts kinetic energy in the wind into useful energy by using airfoil blades. Blade element momentum (BEM) theory becomes very popular due to its simplicity in mathematical calculation as well as accuracy. Hydraulic pitch actuation system has certain advantages due to its versatility, ability to produce constant force and torque irrespective of the disturbances outside of the system, ease and accuracy of control, simplicity, safety and economy. In the present study a semi rotary actuator has been utilized for turbine pitch actuation. In order to extract maximum power from available wind, fractional order PID controller (FOPID) has been developed for pitch control of wind turbine rotor blade. The performances of PID as well as FOPID controller have been compared with available wind data. The performance of FOPID controller was satisfactory compare to PID controller.

Use of the Savonius Wind Turbine for the Needs of Public Lighting

2014 ◽  
Vol 1008-1009 ◽  
pp. 179-182
Author(s):  
Iveta Gressová
Keyword(s):  
Energy Source ◽  
Renewable Energy ◽  
Wind Energy ◽  
Wind Turbine ◽  
Energy Use ◽  
Renewable Energy Sources ◽  
Energy Sources ◽  
Geothermal Heat ◽  
Current Generation ◽  
Savonius Wind Turbine

Our planet gives us many mineral sources, but they have a big disadvantage. They are finite. Non-renewable energy sources are enough only for decades, exceptionally for centuries. Current generation is aware of the importance of using other energy sources, such as sunlight, wind, rain, tides, waves and geothermal heat. These energy sources are renewable. It means that they come from sources, which are naturally replenished on a human timescale. One of these sources is wind energy. Use of this kind of energy source needs an initial investment, but it can reduce cost of running a household and other sectors. This article is about Savonius wind turbine and its use for the needs of public lighting.

Energy Harvesting Using Small Renewable Energy Sources: UAV Application

2015 ◽  
Author(s):  
Sayem Zafar ◽  
Mohamed Gadalla
Keyword(s):  
Power Generation ◽  
Renewable Energy ◽  
Fuel Cell ◽  
Energy Harvesting ◽  
Wind Turbine ◽  
Renewable Energy Sources ◽  
Solar Flux ◽  
Energy Sources ◽  
Micro Power ◽  
Energy Harvesting System

A renewable energy harvesting system is designed and tested for micro power generation. Such systems have applications ranging from mobile use to off-grid remote applications. This study analyzed the use of micro power generation for small unmanned aerial vehicle (UAV) flight operations. The renewable energy harvesting system consisted of a small wind turbine, flexible type PV panels and a small fuel cell. Fuel cell is considered the stable source while PV and wind turbine produced varying power output. The load of around 250 W is simulated by a small motor. The micro wind turbine with the total length of 4.5 m and the disk diameter of 1.8 m is tested. The micro wind turbine dimensions make it big enough to be used to charge batteries yet small enough to be installed on rooftops or easily transportable. The wind turbine blades are installed at an angle of 22°, with respect to the disk plane, as it gives the highest rotation. The voltage and current output for the corresponding RPM and wind speeds are recorded for the wind turbine. Two 2 m and a single 1 m long WaveSol Light PV panels are tested. The PV tests are conducted to get the current and voltage output with respect to the solar flux. The variation in solar flux represented the time of day and seasons. A 250 W PEM fuel cell is tested to run the desired load. Fuel cell’s hydrogen pressure drop is recorded against the output electrical power and the run time is recorded. System performance is evaluated under different operating and environmental conditions. Data is collected for a wide range of conditions to analyze the usability of renewable energy harvesting system. This energy harvesting method significantly improves the usability and output of the renewable energy sources. It also shows that small renewable energy systems have existing applications.

scholarly journals Techniques for Ensuring Fault Ride-Through Capability of Grid Connected DFIG-Based Wind Turbine Systems: A Review

2021 ◽  
Vol 18 (1) ◽  
pp. 39-46
Author(s):  
M. Shuaibu ◽  
A.S. Abubakar ◽  
A.F. Shehu
Keyword(s):  
Renewable Energy ◽  
Wind Turbine ◽  
Electricity Market ◽  
Energy Demand ◽  
Reactive Power ◽  
Short Circuit ◽  
Renewable Energy Sources ◽  
Dynamic Performance ◽  
Energy Sources ◽  
Fault Ride Through

Renewable energy sources (RES) are being integrated to electrical grid to complement the conventional sources to meet up with global electrical energy demand. Among other RES, Wind Energy Conversion Systems (WECS) with Doubly Fed Induction Generator (DFIG) have gained global electricity market competitiveness because of the flexible regulation of active and reactive power, higher power quality, variable speed operation, four quadrant converter operation and better dynamic performance. Grid connected DFIG-based WECS are prone to disturbances in the network because of direct connection of stator windings to grid. The ability of the Wind Turbine (WT) to remain connected during grid faults is termed the Fault Ride-Through (FRT) capability. The grid code requirement for integrating the DFIG-based WTs to power networks specified that they must remain connected and support the grid stability during grid disturbances of up to 1500 ms. The use of compensation devices offers the best FRT compliance thereby protecting the DFIG and the converters from voltage fluctuations and over currents during the grid fault. The paper presents a review of techniques employed in ensuring FRT compliance. The article also proposes the state-of-the-art techniques for compensating voltage sag/swell and limiting the fault short-circuit current. Keywords: Renewable energy sources, DFIG, wind turbine system, fault ride-through, grid codes, dual-functional DVR

scholarly journals A Methodology for the Estimation of the Wind Generator Economic Efficiency

2017 ◽  
Vol 54 (6) ◽  
pp. 21-31
Author(s):  
G. Zaleskis
Keyword(s):  
Renewable Energy ◽  
Wind Turbine ◽  
Economic Efficiency ◽  
Power Supply ◽  
Fossil Fuel ◽  
Renewable Energy Sources ◽  
Energy Sources ◽  
Environmental Load ◽  
Fuel Delivery ◽  
Technological Base

Abstract Integration of renewable energy sources and the improvement of the technological base may not only reduce the consumption of fossil fuel and environmental load, but also ensure the power supply in regions with difficult fuel delivery or power failures. The main goal of the research is to develop the methodology of evaluation of the wind turbine economic efficiency. The research has demonstrated that the electricity produced from renewable sources may be much more expensive than the electricity purchased from the conventional grid.

Sign in / Sign up

Export Citation Format

Share Document