Technological quality assurance of the surface layer and operational properties of machine parts by electroerosion treatment

2021 ◽  
Vol 2021 (11) ◽  
pp. 30-37
Author(s):  
Sergey S'yanov
Keyword(s):  
Wear Resistance ◽  
Surface Layer ◽  
Corrosion Rate ◽  
Endurance Limit ◽  
Mechanical Parameters ◽  
Technological Support ◽  
Technological Quality ◽  
Machine Parts ◽  
Surface Layer Quality

Dependences for determining geometric, physical and mechanical parameters of the surface layer quality, wear resistance, corrosion rate and endurance limit depending on the modes and conditions of electroerosion treatment of machine parts have been given. These dependences allow determining optimal modes and conditions of electroerosion treatment to ensure the required parameters of the quality of the surface layer (with a two–stage approach - design and technological support of operational properties), wear resistance, corrosion rate and endurance limit (with a single-stage approach - direct technological support).

scholarly journals Rated definition of degree of cutter coating influence upon parameters of surface layer quality of parts worked

2017 ◽  
Vol 2 (7) ◽  
pp. 20-24
Author(s):  
Вячеслав Безъязычный ◽  
Vyacheslav Bezyazychnyy ◽  
Максим Басков ◽  
Maksim Baskov
Keyword(s):  
Surface Roughness ◽  
Surface Layer ◽  
Residual Stresses ◽  
Layer Surface ◽  
Wear Resistant Coatings ◽  
Cutter Wear ◽  
Definition Of ◽  
Surface Layer Quality ◽  
The Impact

The impact of cutter wear-resistant coatings upon cutting process parameters and characteristics of surface layer quality in the parts worked: residual stresses, a degree and a depth of work hardening of a surface layer, surface roughness is investigated.

scholarly journals Problems of Analyzing Microstructure Images in Assessing the Impact of Technological Parameters of Combined Strain Wave Hardening on the Quality of the Surface Layer

2019 ◽  
Author(s):  
Андрей Киричек ◽  
Andrey Kirichek ◽  
Дмитрий Соловьев ◽  
Dmitriy Solovyev ◽  
Александр Хандожко ◽  
...  
Keyword(s):  
Surface Layer ◽  
Thermal Treatment ◽  
Strain Wave ◽  
Technological Parameters ◽  
Steel Microstructure ◽  
Main Indicator ◽  
Metallographic Images ◽  
Surface Layer Quality ◽  
The Impact

The problems of analyzing metallographic images and the method of their solution using modern software for the analysis of metallographic images are described. There is given an analysis of microstructure images as the main indicator of the surface layer quality by the example of studying the research results of strain wave hardening combinations and chemical-thermal treatment, in particular the influence of previous strain wave hardening and subsequent thermal and chemical- thermal treatment on the alloy steel microstructure or previous thermal and chemical- thermal treatment and subsequent strain wave hardening. On the basis of the analysis the effectiveness of strain wave hardening and chemical and thermal treatment is established.

An accelerated method of inspecting the surface-layer quality of parts during machining

1981 ◽  
Vol 17 (1) ◽  
pp. 91-93
Author(s):  
P. A. Rutman ◽  
N. V. Pertsov ◽  
V. S. Lobantsova
Keyword(s):  
Surface Layer ◽  
Surface Layer Quality

scholarly journals THE USE OF PULSE MODULATION AS A WAY TO IMPROVE THE STRENGTH CHARACTERISTICS OF PLASMA COATINGS

2021 ◽  
Author(s):  
A.M. Kadirmetov ◽  
◽  
V.N. Bukhtoyarov ◽  
V.A. Ivannikov ◽  
◽  
...  
Keyword(s):  
Wear Resistance ◽  
Strength Properties ◽  
Strength Characteristics ◽  
Plasma Process ◽  
Electrical Parameters ◽  
Pulse Modulation ◽  
Coat Ings ◽  
Machine Parts ◽  
Plasma Coatings

Currently, much attention is paid to improving the wear resistance of the sur-face of machine parts. It is possible to improve the quality of surfaces with the use of plasma coat-ings. However, these coatings do not always provide the necessary strength properties. The article considers one of the ways to improve the strength characteristics – the modulation of the electrical parameters of the plasma process.

scholarly journals Surface layer quality in compressor titanium blades at multiaxes deep grinding

2017 ◽  
Vol 2 (12) ◽  
pp. 15-19
Author(s):  
В. Полетаев ◽  
V. Poletaev ◽  
Е. Цветков ◽  
E. Tsvetko
Keyword(s):  
Titanium Alloy ◽  
Surface Layer ◽  
Residual Stresses ◽  
Gas Turbine ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Blade Surface ◽  
A Value ◽  
Surface Layer Quality

The investigation results of technological conditions impact at multiaxes deep grinding upon quality of titanium alloy blade surface layer in the compressors of gas turbine engines (GTE) are presented. The grinding mode impact upon a surface and a value of residual stresses in a surface layer of blades is defined and also conditions for defect occurrence as burns on blade surfaces under machining are detected.

scholarly journals Surface Treatment for Improving Selected Physical and Functional Properties of Tools and Machine Parts—A Review

2020 ◽  
Vol 60 (1) ◽  
pp. 23-35
Author(s):  
Daniel Toboła ◽  
Janusz Kalisz ◽  
Kazimierz Czechowski ◽  
Iwona Wronska ◽  
Zbigniew Machynia
Keyword(s):  
Surface Treatment ◽  
Physical Vapor Deposition ◽  
Cost Effective ◽  
Mechanical Grinding ◽  
Treatment Processes ◽  
Functional Quality ◽  
Technological Quality ◽  
Machine Parts ◽  
Machining Properties

Wear resistance, which is one of the main technological quality features of machine parts and tools, is determined by the properties of their surface layer. The demand for high-quality products forces manufacturers to use modern structural and tooling materials as well as efficient and cost-effective methods of their treatment. The paper presents the results of research on selected properties of tools made of tool steels and sintered carbides, as well as parts made of aluminum alloy subjected to selected surface treatment processes, such as mechanical (grinding, turning, milling, burnishing) and thermo-chemical (nitriding, sulfonitriding) processes, and physical vapor deposition (PVD) of coatings. The presented results, including analyses of the surface geometric structure, microstructure, and microhardness, as well as tribological and machining properties of selected materials, indicate the possibility of improving the functional quality of tools and machine parts.

scholarly journals Agricultural machine parts quality control by dynamic non-destructive methods

2018 ◽  
Vol 226 ◽  
pp. 04034 ◽  
Author(s):  
Alexey N. Beskopylny ◽  
Viktor B. Rykov ◽  
Elena M. Zubrilina ◽  
Andrey D. Chistyakov
Keyword(s):  
Quality Control ◽  
Wear Resistance ◽  
Manufacturing Process ◽  
Mechanical Characteristics ◽  
Point Of View ◽  
Agricultural Machinery ◽  
Machine Parts ◽  
Non Destructive ◽  
Destructive Methods

The problem of quality control of agricultural machinery parts by means of dynamic non-destructive methods of impact indentation of conical shape indenters is considered. Quality of the crucial parts is considered from the point of view of a set of mechanical characteristics that determine the strength, hardness, wear resistance and deformability. These characteristics must be known and be able to control on all the details promptly and accurately both in the manufacturing process and in operation. The mechanical characteristics of metals are stochastic in nature. For this purpose, an impact indentation device was developed, and the method based on probabilistic laws of dispersion of mechanical characteristics is obtained.

Sign in / Sign up

Export Citation Format

Share Document