scholarly journals ESTIMATING THE PROBABILITY OF THE EMERGENCY OPERATION OF THE QUARRY ELECTRIC LOCOMOTIVE TRACTION ELECTRIC DRIVE

Author(s):  
Artem Artemenko ◽  
Oleksii Chornyi ◽  
Valeriy Sydorenko ◽  
Serhii Serhiienko ◽  
Yurii Zachepa ◽  
...  

The paper deals with the problem of the assessment of the functionality of the multi-motor direct current traction electric drive of the quarry electric locomotive. The problem of the failure of electric drive motors because of extremely unsatisfactory state of the rail tracks and the wear of wheel pairs is analyzed. Taking into account the number of the existing repaired electric motors the probability of fitting up the traction electric drive with the electric motors with the widest electrical parameters variety is determined.

2020 ◽  
Vol 4 (52) ◽  
pp. 27-32
Author(s):  
A. Artemenko ◽  
◽  
O. Chornyi ◽  

Purpose. The purpose of the work is to conduct experimental studies to determine the parameters of DC motors of sequential excitation in dynamic modes of operation for use in setting up the control system of the electric drive. The paper presents the results of experimental studies to determine the parameters of the traction electric drive of direct current quarry electric locomotive. The research was conducted on the basis of Kremenchuk Mykhailo Ostrohradskyi National University with the use of a laboratory research stand with electromechanical equipment that simulates the operation of a traction drive, namely slippage of traction wheels when changing clutch conditions and differences in electrical parameters of traction motors. Methodology. The parameters were determined on the basis of a set of methods based on the measured instantaneous values of the state variables of the electric drive. The efficiency of application of the method of state space and the method which uses instantaneous values of current and voltage of the motor in the quasi-constant mode at power supply from the valve energy converter is proved. Results. The results obtained in the course of research indicate the possibility of calculating the parameters with an accuracy of 10 %. The verification of the obtained results is checked by subtracting the coefficient of determination and the sum of the squares of the deviations for the experimental data calculated on the basis of certain parameters. Originality. The accuracy of parameter determination is ensured by the use of instantaneous values of current and voltage at adjacent time intervals, and the voltage at the armature is formed by the control system and changes over time, ensuring the start of the motor with starting current limitation. Practical value. The developed computerized laboratory stand allows to measure instantaneous values of state variables and to carry out calculations of electric parameters of traction engines, and also to investigate static, power and dynamic operating modes of electromechanical transmissions of vehicles, both in regular operating modes, and to simulate various emergency operating modes, in particular. Figures 5, tables 2, references 7.


2020 ◽  
pp. 45-48
Author(s):  
S.I. Malafeev ◽  
A.A. Malafeeva ◽  
V.I. Konyashin

A correction method for regulating the mechatronic system of a «DUO-300» rolling mill with a direct current electric drive is considered. The results of the study of dynamic processes in the mechatronic system with the proposed correction are presented. Keywords rolling mill, mechatronic system, model, electric drive, engine, regulator, correction. [email protected]


2013 ◽  
Author(s):  
Boris Beloousov ◽  
Tatiana I. Ksenevich ◽  
Dmitry Izosimov

Author(s):  
Виктор Алексеевич Барский ◽  
Роман Владимирович Афенченко ◽  
Роман Анатольевич Быканов

2020 ◽  
Vol 220 ◽  
pp. 01039
Author(s):  
Shakhboz Dadabaev ◽  
Elena Gracheva

The results of the analysis of transient and technological processes of the irrigation pumping station of the first lift, taking into account the negative starting effects on the synchronous electric drive, are considered. The analysis and review of the ways of regulating the performance of the units of the irrigation pumping station of the first lift are made, and the main difficulties of the existing methods of regulating the pump supply are revealed. Computer simulation of starting modes of high-voltage synchronous electric motors with direct and soft start, where soft starter was used for soft start, was carried out. The simulation took into account the changes in the currents of all phases of the electric motor, the electromagnetic torque, the motor speed, the effective value of the current, as well as the static torque. The introduction of semiconductor soft starters for electric drives of high-power pumping units has been substantiated.


2020 ◽  
Author(s):  
Zenon Syroka

A universal controller for brushless direct current (BLDC) motors was designed in the presented article. The system is controlled from the user console where operating parameters are set by the user. Signals are transmitted by cables to microcontrollers which control and monitor electric motors. Microprocessors communicate via a data bus. The controller contains the user console module and the motor control module. The user console module generates commands, and motors are controlled and monitored by the control module. Motor control modules operate independently, and each brushless motor has a dedicated control module. Brushless motors can be controlled in bipolar or unipolar mode. The control method is selected by the operator. The user console and motor controllers communicate via the I²C bus.  


Sign in / Sign up

Export Citation Format

Share Document