scholarly journals Increasing the parameters of electrical distribution networks of town districts with low load density

2020 ◽  
Vol 1 (57) ◽  
pp. 28-32
Author(s):  
V. Perepecheny
Keyword(s):  
Power Supply ◽  
Distribution Networks ◽  
Voltage Regulation ◽  
Parameter Distribution ◽  
Electrical Networks ◽  
Supply Networks ◽  
Transformer Substation ◽  
Low Load ◽  
The Impact ◽  
Selection Of

This article presents the results of research on the parameters of electrical networks with a voltage of 6 (10) and 0.38 kV in relation to capital investments. The analysis of existing methods of estimation of parameters before designing for power supply networks in a small town with low load density is carried out. In modern conditions, in the distribution of electrical networks is of paramount importance the introduction of energy-saving schemes and parameters of power supply systems. One of the main ways to implement them is to increase the efficiency of 6-10 / 0.38 kV networks. In the actual design of electrical networks, economic proportionality can not always be maintained for various reasons: the impact of technical constraints, the discreteness of the rated power of transformers and cable crossing scales, a significant deviation of individual capacities of consumers from the average value. In that case there is an increase in the reduced costs. A methodology for determining the optimal power of transformer substations and optimal sections of 0.38 kV power transmission lines is proposed, taking into account the probable nature of the applied load. When assembling the power supply circuit for the optimal form of parameters, voltage, principles of voltage regulation and reactive power compensation. Decisions of this kind are substantiated by technical and economic comparisons of a series of technically acceptable variants of power supply networks. An important measure that facilitates the selection of the most economical option is the assessment of the proposed project, which relates to the selection of the optimal capacity of transformer substation (TS) networks using calculation formulas. The aim of the research was to improve the existing methods on the basis of separate accounting of the reliability coefficient of 0.38 kV and 6-10 kV network. Key words - electric power supply network, network parameters, transformer substation, load density, line wire section, specific load, unit costs, optimum parameter, distribution networks, electric energy.

scholarly journals ELECTRIC SUPPLY OF UNDERGROUND CONSUMERS OF DEEP ENERGY-INTENSIVE MINES

2018 ◽  
pp. 25-46
Author(s):  
F. P. Shkrabets
Keyword(s):  
Power Supply ◽  
Supply Voltage ◽  
Maximum Load ◽  
Electrical Equipment ◽  
Transport Systems ◽  
Local Power ◽  
Electrical Networks ◽  
Electric Networks ◽  
Supply Networks ◽  
Technical And Economic Indicators

The increase in the capacity of cleaning and construction vehicles for highcapacity and energy-intensive mines calls for an increase in the  supply voltage of cleaning and tunneling combines, as well as  transport systems: from a voltage of 660 V switched to 1140 V, and  now to 3300 V. This allows improving technical and economic  indicators for clearing and access areas, as well as improving the reliability of local Power Supply Systems (PSS). However, this  trend prevents the supply of underground electric networks with a  voltage of 6 kV, in connection with which the problem arises of  increasing the voltage of supply networks. To date, it has become  possible to apply the 10 kV voltage to the operation, which is most  acceptable for the use of electrical equipment for electrical networks  and protection devices. Leading educational, research and design  organizations were engaged in research on this issue. An analysis of the results of the research showed that switching to 10 kV voltage is  justified and timely. At the same time, 35 kV voltage is not removed  from the agenda, which is technically feasible and economically  justified, but there are problems with the safety of its operation in  underground workings, which requires appropriate refinement. This  level of voltage will improve the quality of electricity.Conclusions: 1. Application of 35 kV voltage in the underground power supply system of coal and ore mines is advisable at a depth of more than 1000 m with a maximum load of at least 1000 kVA at the  level of the stem cables.2. Application of 35 kV voltage in underground electrical networks will allow to significantly improve the quality indicators of voltage,  reliability, and economy of the system due to the current unloading  of the most important element of SES, such as stem cables.3. Analysis of the main parameters and characteristics of electrical mine electrical equipment gives reason to believe that it allows  implementing a trend of 35 kV deep input to deep horizons of mines  (mines) and placement of 35/6 kV substations on working horizons.

scholarly journals Design of power substation placement with GIS tracing tools

Vestnik IGEU ◽  
2019 ◽  
pp. 75-83 ◽  
Author(s):  
А.В. Gadalov ◽  
S.V. Kosyakov
Keyword(s):  
Low Voltage ◽  
Power Grid ◽  
Distribution Networks ◽  
Power Lines ◽  
Electrical Networks ◽  
Voltage Distribution ◽  
Transformer Substation ◽  
Urban Distribution ◽  
Gis Environment

Analytical methods that are currently used to determine transformer substation placement in the process of planning the development of low-voltage distribution networks are based on calculating the lengths of future power lines by Euclidean distance, or methods for comparing several alternative placement options taking into account the routes of power lines. Assumptions made in this case lead to the fact that for the selected location of the substation, the total cost of the power lines connected to it may exceed the possible minimum. The use of modern GIS technologies allows simulating the routes of laying power lines on the map bypassing the existing obstacles or finding the cheapest routes for crossing them. These opportunities can be used to improve the quality of designing urban distribution networks through minimizing the construction cost of new power lines. However, the methods of organizing the solution to such a design problem have not yet found practical applications. The aim of the work is to develop a practical method of designing the placement of power substations in the GIS environment and its verification using real data. The paper uses methods of spatial modeling in the GIS environment, including methods of overlay, finding optimal paths on graphs and power grid inventory, as well as discrete optimization methods. A method of computer-aided design of transformer substation placement in urban distribution low-voltage networks is proposed and implemented as a GIS software module, which allows finding the optimal options of the placement cost at the stages of network scheme selection. The paper presents the results of the method analysis based on studying the design of the power grid scheme of Ivanovo city quarters as an example. The results confirm the possibility of using GIS to improve the quality of decisions on the choice of placement of low voltage distribution substations when designing urban electrical networks and can be used in the electrical networks CAD.

scholarly journals Allocation of 0.4 kV PTL Sectionalizing Units under Criteria of Sensitivity Limits and Power Supply Reliability

2021 ◽  
Vol 11 (24) ◽  
pp. 11608
Author(s):  
Alina Vinogradova ◽  
Alexander Vinogradov ◽  
Vadim Bolshev ◽  
Andrey Izmailov ◽  
Alexey Dorokhov ◽  
...  
Keyword(s):  
Transmission Lines ◽  
Power Supply ◽  
Power Transmission ◽  
Short Circuit ◽  
Reducing Power ◽  
Power Transmission Lines ◽  
Electrical Networks ◽  
The Cost ◽  
The Impact ◽  
Supply Reliability

Sectionalizing 0.4 kV power transmission lines (PTL) improves power supply reliability and reduces electricity undersupply through the prevention of energy disconnection of consumers in the event of a short circuit in the power line behind the sectionalizing unit (SU). This research examines the impact of sectionalizing on power supply reliability and reviews the literature on sectionalizing unit allocation strategies in electrical networks. This paper describes the experience of the use of sectionalizing units with listing strengths and weaknesses of adopted technical solutions and describes the new structure of sectionalizing units. A new methodology is proposed, whereby there are two criteria for allocating SU in 0.4 kV power transmission lines. The first criterion is the sensitivity limits against single-phase short circuits used for calculating the maximum distance at which SU can be installed. The second criterion is power supply reliability improvement, evaluating the cost-effectiveness of installing sectionalizing equipment by reducing power supply outage time. The established methodology was put to the test on an actual electrical system (Mezenka village, Orel area, Russia), which demonstrated that the installation of a sectionalizing unit paid off.

scholarly journals Effective mode of voltage in the electrical network when powering ships of the technical fleet and floating objects from the shore

2021 ◽  
Vol 2131 (5) ◽  
pp. 052005
Author(s):  
Y Denchik ◽  
D Zubanov ◽  
M Romanov
Keyword(s):  
Power Transmission ◽  
Experimental Studies ◽  
Voltage Regulation ◽  
Electrical Network ◽  
Negative Consequences ◽  
Electrical Networks ◽  
Complex Load ◽  
Floating Crane ◽  
Floating Objects ◽  
The Impact

Abstract The article discusses negative consequences of a decrease in the quality of electrical energy when feeding ship receivers of electricity from coastal sources, a method is proposed to ensure an effective voltage regime in the electrical network when feeding ships of technical fleet and floating objects from the coast. Definition of the equilibrium voltage mode at the “shore-to-ship” power supply scheme is given, the equivalent circuit of supply line (feeder) for the river fleet is developed, significant regulatory effects of the “shore-to-ship” power transmission elements are determined. Experimental studies of static characteristics of floating crane of R-99 project have been carried out. According to the results of the experiment, regulating effects on the voltage of the complex load of 0.4 kV of floating crane were determined. A calculation program for personal electronic computers has been compiled, which provides an assessment of the impact of voltage deviations in electrical networks when regulating the load. The law of voltage regulation in the “shore-to-ship” power transmission is proposed. An experimental verification of effectiveness of proposed regulation law was carried out while ensuring the equilibrium mode.

scholarly journals Reactive power control

2021 ◽  
pp. 36-39
Author(s):  
Vasyl Kalinchyk ◽  
Vitaliy Pobigaylo ◽  
Vitaliy Kalinchyk ◽  
Viktor Skosyrev
Keyword(s):  
Power Control ◽  
Power Supply ◽  
Power Supply System ◽  
Reactive Power ◽  
Voltage Regulation ◽  
Supply System ◽  
Source Information ◽  
Reactive Power Control ◽  
Power Mode ◽  
The Impact

The article investigates the methods of control of reactive power modes. It is shown that ensuring the efficiency of electricity transmission and distribution is inseparable from setting and solving problems related to reducing electricity losses in networks. Moreover, one of the most effective ways to reduce electricity losses, as well as improve its quality at the terminals of electrical receivers is to compensate for reactive power, which is carried out using various compensating devices. It is shown that the control of the reactive power mode is carried out in accordance with the Methodology for calculating the fee for the flow of reactive energy between the power transmission organization and its consumers. It is shown that the indicator of economically advantageous value of the level of reactive energy consumption can be cos φз, the value of which is predetermined. The procedure for controlling the reactive power mode contains two main stages: the stage of determining the magnitude of the possible reduction of the current cos φ above the set and the stage of determining and implementing control effects aimed at eliminating possible deviations. Preferably, it is preferable to focus on those methods that are based on the study of forecast estimates, which constitute the source information for management decisions. It is expedient to use adaptive methods of exponential smoothing as a basis for operative forecasting of electric loading. Reactive power mode is controlled by compensating units. It is shown that the control of voltage modes in the power supply system significantly affects the modes of reactive power consumption. In this regard, it is advisable to comprehensively solve the problem of reactive power control both by controlling the compensating units and the impact on the voltage regimes of the power supply system. In the calculation model, the reactive load of the distribution network is given by its static characteristics, which can be the basis for regulating the reactive load. To implement regulation in the power supply centers of electrical networks, technical means are provided on the basis of changing the transformation coefficient or generating reactive power by counter-voltage regulation.

scholarly journals Substantiation of the choice of the replacement scheme of line for mathematical modeling of 20 kV power supplies.

2021 ◽  
Vol 24 (1) ◽  
pp. 69-72
Author(s):  
SKRYPNYK S. ◽  
Keyword(s):  
Power Systems ◽  
Transmission Lines ◽  
Power Supply ◽  
Electrical Equipment ◽  
Distribution Networks ◽  
Power Line ◽  
Power Lines ◽  
Electrical Networks ◽  
Overhead Lines ◽  
Replacement Scheme

In the current global economic crisis and acute shortage of energy resources, increasing importance is attached to energy saving measures, economical and careful consumption of raw materials, materials, electricity and heat, environmental safety of industrial production. During the reconstruction of existing power supply systems of industrial enterprises, modern progressive solutions should be considered and implemented, morally and physically obsolete electrical equipment should be replaced, namely the introduction of new electrical equipment for transition from 6/10 kV to 20 kV in Ukrainian power systems. It is also necessary to pay attention to the improvement of power supply circuits and distribution networks, the implementation of complex automation of complex technological processes, rational compensation of reactive power at all levels of power supply systems. In the power system, the main transport link is the power line. Power lines (transmission lines) are long conductors suspended at a safe distance from the ground overhead lines (overhead lines) or cable lines (overhead lines) in which conductors are insulated from each other and from the environment and protected by insulation and armor electricity. Power lines are the most massive elements of the power supply system, they connect the individual nodes of its circuit. Longitudinal and transverse parameters are distinguished in alternative schemes. The load current flows through the longitudinal parameters, voltage is applied to the transverse ones. The replacement circuit of the electrical network consists of replacement circuits of the following elements: power lines, transformers, reactors, capacitors, loads, power sources. Calculating the steady-state modes of power systems, the substitution schemes of the elements are given in a single-line design, because the parameters of all phases are symmetrical. In local and local electrical networks with a relatively short length and low rated voltage, the conduction currents are small compared to load currents. Therefore, in typical electrical calculations of these networks, the capacitive conductivity of the lines is not taken into account. However, for these networks, the accounting of capacitive conductivities is necessary when considering some modes, the existence of which in itself is due only to the presence of capacitive conductivities. For example, the mode of single-phase ground fault in a network with isolated or compensated neutral or analysis of the modes of operation of neutrals of electrical networks of different voltage classes cannot be performed without taking into account the capacitive conductivity of these networks. When switching the power system of Ukraine to the nominal voltage of 20 kV, it should be taken into account that the transmission line will be replaced in the sections of both the overhead power line and cable power line, namely 35, 10, 6 kV. The replacement scheme must describe all the characteristics and properties of the elements of cable and overhead lines in accordance with real conditions. Thus, it is not expedient to use simplified substitution circuits that neglect energy parameters and properties of conductors to study the parameters of transmission lines. The use of a complete "P" -shaped scheme for the analysis of the parameters of transmission lines and transmission lines for a voltage of 20 kV is the basis of mathematical modeling of the transmission system in the distribution networks of our country.

Assessment of the Technical and Economic Effect from Using Automatic Voltage Control Devices on 10/0.4 kV Transformers in Power Distribution Networks

Vestnik MEI ◽  
2021 ◽  
pp. 27-36
Author(s):  
Mikhail G. Astashev ◽  
◽  
Artem S. Vanin ◽  
Vladimir M. Korolev ◽  
Dmitriy I. Panfilov ◽  
...  
Keyword(s):  
Power Distribution ◽  
Voltage Control ◽  
Distribution Networks ◽  
Voltage Regulation ◽  
Economic Feasibility ◽  
Electrical Network ◽  
Test Model ◽  
Electrical Networks ◽  
Permissible Limits ◽  
Network Load

The article addresses the problem of ensuring permissible voltage levels in distribution electrical networks of various types: distribution networks of large cities, regional distribution electrical networks, and distribution electrical networks containing renewable energy sources. The most typical factors causing the voltage to go beyond the permissible limits specified by the relevant regulatory documents are pointed out. The negative factors conducive to the voltage at the consumer end deviating from the permissible limits, including a long length of network lines, high network load, low controllability of the network, load schedule nonuniformity, and poor observability of the network, are analyzed. The existing principles of voltage control in electrical distribution networks, namely, automatic and seasonal regulation, are studied. A distribution electrical network test model representing a real network fragment is developed. The model operation modes have been verified based on the data of measurements carried out in the original distribution electrical network. The voltage distributions in a medium voltage network during its operation under the conditions of the highest and lowest loads are demonstrated. It is shown, on the test model example, how the network voltage can be controlled by automatically regulating the voltage at the power supply center and selecting a fixed position of the NLTC at 10/0.4 kV transformer substations. It is shown that the use of power transformer OLTCs does not ensure sufficient means for adequately controlling the voltage in networks containing long power lines and featuring highly nonuniform seasonal and daily load schedules. The technical efficiency and economic feasibility of using automatic voltage regulation devices on 10/0.4 kV transformers for local voltage control are analyzed. The economic efficiency of applying automatic voltage regulation devices at 6--10/0.4 kV substations was evaluated in comparison with other means for improving the power distribution network voltage quality by upgrading the 10 kV feeder lines or installing a voltage booster at the inlet to the problematic 10 kV network section. The application field of automatic voltage regulators in the form of semiconductor devices for regulating the transformer output voltage at distribution transformer substations is shown.

scholarly journals Research on Forecasting Method of Distribution Network Investment Scale of Municipal Power Supply Enterprise Considering Power Supply Division and Cost Difference Level

2021 ◽  
Vol 245 ◽  
pp. 01032
Author(s):  
Gou Quanfeng ◽  
Yang Jie ◽  
Zhou Fei ◽  
Hu Lin ◽  
Yu Guangxiu ◽  
...  
Keyword(s):  
Power Supply ◽  
Large Scale ◽  
Distribution Network ◽  
Forecast Model ◽  
Distribution Networks ◽  
Lean Management ◽  
Investment Planning ◽  
Management Level ◽  
Network Investment ◽  
The Impact

In recent years, in order to adapt to the situation of rapid economic and social development, my country’s power supply companies have invested large-scale funds to build distribution networks, and upgraded urban and rural power grids, effectively supporting the rapid growth of power demand and the reliability of power supply. Continuous improvement of power quality. While the scale of investment in the distribution network continues to remain high, problems such as focusing on investment and neglecting revenue, focusing on project establishment and neglecting management also exist to varying degrees. Therefore, reasonably predicting the scale of investment in the distribution network and improving the lean management level of the investment and construction of the distribution network have become key issues that power supply companies need to solve. This paper takes my country’s municipal power supply companies as the research object, combines the actual business development of the company’s distribution network investment planning, and fully considers the impact of the company’s power supply district management and the level of cost differences on the investment scale of the distribution network, and builds a fit on this basis. The distribution network investment planning forecast model of the actual business work of the enterprise guides the municipal power supply enterprises to improve the lean management level of the distribution network investment and construction.

scholarly journals Methodology for managing equipment repairs in oilfield electrical networks

2020 ◽  
pp. 139-155
Author(s):  
Vladimir Levin ◽  
◽  
Nikolay Guzhov ◽  
Natalya Chernenko ◽  
Ammar Yahya ◽  
...  
Keyword(s):  
Power Supply ◽  
Risk Function ◽  
Electrical Equipment ◽  
Distribution Networks ◽  
Condition Index ◽  
Technical Condition ◽  
Technical Diagnostics ◽  
Electrical Networks ◽  
Destructive Testing ◽  
Risk Event

An innovative methodology for managing repairs in distribution networks and power supply systems for oilfield facilities is proposed in this paper. The methodology makes it possible to select optimal solutions in accordance with the priority management goal by formalizing a risk-based model for planning maintenance and repair (M&R) of electrical equipment with a "condition-based maintenance" strategy. One of the main options in the complex of M&R management tasks is an adaptive model of the technological map for the repairs of power facilities, formed in compliance with a number of key principles. The developed model allows you to optimize the volume and complexity of repairs of electrical equipment of a certain type based on the minimum composition of technological operations necessary to eliminate the identified defects. Detection of defects in electrical equipment is achieved by using methods of technical diagnostics and non-destructive testing. In this case, each of the defects is recorded in the defect statement for the object, with the determination of the degree of criticality and fixing a specific type of corrective action. Optimal prioritization of electrical equipment repairs is performed in accordance with the minimum risk function under current restrictions on reliability (an equipment technical condition index) and available resources (total maintenance costs). The originality of the implementation of a key risk event – a power supply failure of an oilfield facility provides calculating the probability and severity of the consequences of an electrical equipment failure taking into account its technical condition and features of the power supply scheme. The given example illustrates the effectiveness of the proposed approach and emphasizes the validity of optimal decisions. The key components of the developed methodology have found practical application in the conditions of real operation of the equipment of oilfield facilities.

Sign in / Sign up

Export Citation Format

Share Document