scholarly journals Improving the Corrosion Resistance of AISI 316L Steel for Semiconductor Piping by Controlled Delta-Ferrite Content

2022 ◽  
Vol 60 (1) ◽  
pp. 46-52
Author(s):  
Young Woo Seo ◽  
Chan Yang Kim ◽  
Bo Kyung Seo ◽  
Won Sub Chung

This study evaluated changes in delta-ferrite content depending on the preheating of AISI 316L stainless steel. We also determined the reasons for the variation in delta-ferrite content, which affects corrosion resistance. Changes in delta-ferrite content after preheating was confirmed using a Feritscope, and the microstructure was analyzed using optical microscopy (OM). We found that the delta-ferrite microstructure size decreased when preheating time was increased at 1295 oC, and that the delta-ferrite content could be controlled through preheating. Potentiodynamic polarization test were carried out in NaCl (0.5 M) + H2SO4 (0.5 M) solution, and it was found that higher delta-ferrite content resulted in less corrosion potential and passive potential. To determine the cause, an analysis was conducted using energy-dispersive spectroscopy (EDS), which confirmed that higher delta-ferrite content led to weaker corrosion resistance, due to Cr degradation at the delta-ferrite and austenite boundaries. The degradation of Cr on the boundaries between austenite and delta-ferrite can be explained by the difference in the diffusion coefficient of Cr in the ferrite and austenite. A scanning electron microscopy (SEM) analysis of material used for actual semiconductor piping confirmed that corrosion begins at the delta-ferrite and austenite boundaries. These results confirm the need to control delta-ferrite content in AISI 316L stainless steel used for semiconductor piping.

2016 ◽  
Vol 58 (6) ◽  
pp. 489-494 ◽  
Author(s):  
Panyasak Phakpeetinan ◽  
Amnuysak Chianpairot ◽  
Ekkarut Viyanit ◽  
Fritz Hartung ◽  
Gobboon Lothongkum

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 6790
Author(s):  
Viera Zatkalíková ◽  
Juraj Halanda ◽  
Dušan Vaňa ◽  
Milan Uhríčik ◽  
Lenka Markovičová ◽  
...  

Plasma immersion ion implantation (PIII) of nitrogen is low-temperature surface technology which enables the improvement of tribological properties without a deterioration of the corrosion behavior of austenitic stainless steels. In this paper the corrosion properties of PIII-treated AISI 316L stainless steel surfaces are evaluated by electrochemical impedance spectroscopy (EIS), potentiodynamic polarization (PP) and exposure immersion tests (all carried out in the 0.9 wt. % NaCl solution at 37 ± 0.5 °C) and compared with a non-treated surface. Results of the three performed independent corrosion tests consistently confirmed a significant increase in the corrosion resistance after two doses of PIII nitriding.


2019 ◽  
Vol 397 ◽  
pp. 39-50
Author(s):  
Djamel Amari ◽  
Hafit Khireddine ◽  
Youcef Khelfaoui ◽  
Nadia Saoula

Abstract. In the present work several films of Ti, TiN, and TiCrN have been coated on AISI 316L stainless steel substrates using magnetron sputtering techniques, in order to improve their surface properties. The morphology and structure of the coatings were analysed using scanning electron microscopy (SEM) and X-ray diffraction (XRD). The electrochemical performances skills in an SBF solution and the adhesion of these deposits were studied to understand these behaviors. From the results it was shown the TiCrN deposition presents the lowest corrosion resistance in the SBF solution, while TiN deposit is the most resistant to corrosion resistance in the same solutions, but its critical load (Lc3-TiN), is relatively low and has a risk of delamination which can limit its use. On the other hand, the Ti deposit exhibits a high resistance to corrosion and a high passivation (icorr (Ti) = 0.57 µA.cm-2 and Rp (Ti) = 67.98 KW.cm2). The critical load (Lc3-Ti = 43.38 N), the crack propagation resistance (CPRs-Ti = 81.64 N) and the scratch hardness (HSL-Ti = 125.75´1012 Pa) also testify to its high adhesion to the AISI 316L substrate. Thus the Ti deposit has proved to be the most favorable protective coating for AISI 316L stainless steel in SBF solution.


2004 ◽  
Vol 58 (1-2) ◽  
pp. 191-195 ◽  
Author(s):  
I. Espitia-Cabrera ◽  
H. Orozco-Hernández ◽  
R. Torres-Sánchez ◽  
M.E. Contreras-Garcı́a ◽  
P. Bartolo-Pérez ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document