scholarly journals Therapeutic Validation of Venous Pulsatile Tinnitus and Biomaterial Applications for Temporal Bone Reconstruction Surgery Using Multi-sensing Platforms and Coupled Computational Techniques

2022 ◽  
Vol 9 ◽  
Author(s):  
Yue-Lin Hsieh ◽  
Xiuli Gao ◽  
Xing Wang ◽  
Fu-Chou Hsiang ◽  
Xinbo Sun ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Temporal Bone ◽  
Therapeutic Effect ◽  
Gelatin Sponge ◽  
Patient Specific ◽  
Pulsatile Tinnitus ◽  
Displacement Sensors ◽  
Sensing Platforms ◽  
Reconstructive Techniques

The application of grafts and biomaterials is a cardinal therapeutic procedure to resolve venous pulsatile tinnitus (PT) caused by temporal bone dehiscence during transtemporal reconstructive surgery. However, the transmission mechanism of venous PT remains unclear, and the sound absorption and insulation properties of different repair materials have not been specified. This study quantifies the vibroacoustic characteristics of PT, sources the major transmission pathway of PT, and verifies the therapeutic effect of different material applications using joint multi-sensing platforms and coupled computational fluid dynamics (CFD) techniques. The in vivo intraoperative acoustic and vibroacoustic characteristics of intrasinus blood flow motion and dehiscent sigmoid plate of a typical venous PT patient were investigated using acoustic and displacement sensors. The acoustical, morphological, and mechanical properties of the dehiscent sigmoid plate, grafts harvested from a cadaveric head, and other biomaterials were acquired using acoustical impedance tubes, micro-CT, scanning electron microscopy, and mercury porosimetry, as appropriate. To analyze the therapeutic effect of our previous reconstructive techniques, coupled CFD simulations were performed using the acquired mechanical properties of biomaterials and patient-specific radiologic data. The peak in vivo intraoperatively gauged, peak simulated vibroacoustic and peak simulated hydroacoustic amplitude of PT prior to sigmoid plate reconstruction were 64.0, 70.4, and 72.8 dB, respectively. After the solidified gelatin sponge–bone wax repair technique, the intraoperative gauged peak amplitude of PT was reduced from 64.0 to 47.3 dB. Among three different reconstructive techniques based on CFD results, the vibroacoustic and hydroacoustic sounds were reduced to 65.9 and 68.6 dB (temporalis–cartilage technique), 63.5 and 63.1 dB (solidified gelatin sponge technique), and 42.4 and 39.2 dB (solidified gelatin sponge–bone wax technique). In conclusion, the current novel biosensing applications and coupled CFD techniques indicate that the sensation of PT correlates with the motion and impact from venous flow, causing vibroacoustic and hydroacoustic sources that transmit via the air-conduction transmission pathway. The transtemporal reconstructive surgical efficacy depends on the established areal density of applied grafts and/or biomaterials, in which the total transmission loss of PT should surpass the amplitude of the measured loudness of PT.

scholarly journals Adapting the Pore Size of Individual, 3D-Printed CPC Scaffolds in Maxillofacial Surgery

2021 ◽  
Vol 10 (12) ◽  
pp. 2654
Author(s):  
David Muallah ◽  
Philipp Sembdner ◽  
Stefan Holtzhausen ◽  
Heike Meissner ◽  
André Hutsky ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cell Migration ◽  
Pore Size ◽  
High Pressures ◽  
Maxillofacial Surgery ◽  
Patient Specific ◽  
Porous Scaffolds ◽  
Bone Augmentation ◽  
3D Printed

Three dimensional (3D) printing allows additive manufacturing of patient specific scaffolds with varying pore size and geometry. Such porous scaffolds, made of 3D-printable bone-like calcium phosphate cement (CPC), are suitable for bone augmentation due to their benefit for osteogenesis. Their pores allow blood-, bone- and stem cells to migrate, colonize and finally integrate into the adjacent tissue. Furthermore, the pore size affects the scaffold’s stability. Since scaffolds in maxillofacial surgery have to withstand high forces within the jaw, adequate mechanical properties are of high clinical importance. Although many studies have investigated CPC for bone augmentation, the ideal porosity for specific indications has not been defined yet. We investigated 3D printed CPC cubes with increasing pore sizes and different printing orientations regarding cell migration and mechanical properties in comparison to commercially available bone substitutes. Furthermore, by investigating clinical cases, the scaffolds’ designs were adapted to resemble the in vivo conditions as accurately as possible. Our findings suggest that the pore size of CPC scaffolds for bone augmentation in maxillofacial surgery necessarily needs to be adapted to the surgical site. Scaffolds for sites that are not exposed to high forces, such as the sinus floor, should be printed with a pore size of 750 µm to benefit from enhanced cell infiltration. In contrast, for areas exposed to high pressures, such as the lateral mandible, scaffolds should be manufactured with a pore size of 490 µm to guarantee adequate cell migration and in order to withstand the high forces during the chewing process.

scholarly journals Identification of in vivo nonlinear anisotropic mechanical properties of ascending thoracic aortic aneurysm from patient-specific CT scans

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
Minliang Liu ◽  
Liang Liang ◽  
Fatiesa Sulejmani ◽  
Xiaoying Lou ◽  
Glen Iannucci ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Aortic Aneurysm ◽  
Thoracic Aortic Aneurysm ◽  
Aortic Wall ◽  
Inverse Methods ◽  
Ct Scans ◽  
Patient Specific ◽  
Accurate Identification ◽  
Anisotropic Mechanical Properties

Abstract Accurate identification of in vivo nonlinear, anisotropic mechanical properties of the aortic wall of individual patients remains to be one of the critical challenges in the field of cardiovascular biomechanics. Since only the physiologically loaded states of the aorta are given from in vivo clinical images, inverse approaches, which take into account of the unloaded configuration, are needed for in vivo material parameter identification. Existing inverse methods are computationally expensive, which take days to weeks to complete for a single patient, inhibiting fast feedback for clinicians. Moreover, the current inverse methods have only been evaluated using synthetic data. In this study, we improved our recently developed multi-resolution direct search (MRDS) approach and the computation time cost was reduced to 1~2 hours. Using the improved MRDS approach, we estimated in vivo aortic tissue elastic properties of two ascending thoracic aortic aneurysm (ATAA) patients from pre-operative gated CT scans. For comparison, corresponding surgically-resected aortic wall tissue samples were obtained and subjected to planar biaxial tests. Relatively close matches were achieved for the in vivo-identified and ex vivo-fitted stress-stretch responses. It is hoped that further development of this inverse approach can enable an accurate identification of the in vivo material parameters from in vivo image data.

scholarly journals Nanohydroxyapatite Effect on the Degradation, Osteoconduction and Mechanical Properties of Polymeric Bone Tissue Engineered Scaffolds

2016 ◽  
Vol 10 (1) ◽  
pp. 900-919 ◽  
Author(s):  
Shima Salmasi ◽  
Leila Nayyer ◽  
Alexander M. Seifalian ◽  
Gordon W. Blunn
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Bone Fractures ◽  
Synthetic Polymers ◽  
Patient Specific ◽  
Promising Alternative

BACKGROUNDStatistical reports show that every year around the world approximately 15 million bone fractures occur; of which up to 10% fail to heal completely and hence lead to complications of non-union healing. In the past, autografts or allografts were used as the “gold standard” of treating such defects. However, due to various limitations and risks associated with these sources of bone grafts, other avenues have been extensively investigated through which bone tissue engineering; in particular engineering of synthetic bone graft substitutes, has been recognised as a promising alternative to the traditional methods.METHODSA selective literature search was performed.RESULTSBone tissue engineering offers unlimited supply, eliminated risk of disease transmission and relatively low cost. It could also lead to patient specific design and manufacture of implants, prosthesis and bone related devices. A potentially promising building block for a suitable scaffold is synthetic nanohydroxyapatite incorporated into synthetic polymers. Incorporation of nanohydroxyapatite into synthetic polymers has shown promising bioactivity, osteoconductivity, mechanical properties and degradation profile compared to other techniques previously considered.CONCLUSIONScientific research, through extensive physiochemical characterisation,in vitroandin vivoassessment has brought together the optimum characteristics of nanohydroxyapatite and various types of synthetic polymers in order to develop nanocomposites of suitable nature for bone tissue engineering. The aim of the present article is to review and update various aspects involved in incorporation of synthetic nanohydroxyapatite into synthetic polymers, in terms of their potentials to promote bone growth and regenerationin vitro,in vivoand consequently in clinical applications.

Feasibility of Determination of Mechanical Properties of Abdominal Aortic Aneurysms by Simultaneous Pressure and Volume Measurements In-Vivo

2008 ◽  
Author(s):  
Marcel van ’t Veer ◽  
Marcel C. M. Rutten ◽  
Jaap Buth ◽  
Nico H. J. Pijls ◽  
Frans N. van de Vosse
Keyword(s):  
Mechanical Properties ◽  
Wall Stress ◽  
Tensile Tests ◽  
Aortic Aneurysms ◽  
Wall Material ◽  
Patient Specific ◽  
Abdominal Aortic ◽  
Risk Of Rupture

In an effort to better predict the risk of rupture of an abdominal aortic aneurysm (AAA), methods have been developed that comprise more than diameter information alone. Wall stress calculations demonstrated superior results compared to the diameter criterion [1]. Accurate wall stress calculations require patient specific geometry, load, and wall properties of the aneurysm [2]. Usually, values for mechanical properties obtained from in-vitro tensile tests of excised aneurysmal wall material are used for wall stress calculations [3]. For obvious reasons such experiments to obtain vessel properties are impossible to perform in patient specific cases for risk assessment.

scholarly journals mRNA-Driven Generation of Transgene-Free Neural Stem Cells from Human Urine-Derived Cells

Cells ◽  
2019 ◽  
Vol 8 (9) ◽  
pp. 1043 ◽  
Author(s):  
Phil Jun Kang ◽  
Daryeon Son ◽  
Tae Hee Ko ◽  
Wonjun Hong ◽  
Wonjin Yun ◽  
...  
Keyword(s):  
Stem Cells ◽  
Neural Stem Cells ◽  
Human Urine ◽  
Neurological Disorders ◽  
Therapeutic Potential ◽  
Embryonic Stem ◽  
Global Gene Expression ◽  
Patient Specific ◽  
Human Neural Stem Cells

Human neural stem cells (NSCs) hold enormous promise for neurological disorders, typically requiring their expandable and differentiable properties for regeneration of damaged neural tissues. Despite the therapeutic potential of induced NSCs (iNSCs), a major challenge for clinical feasibility is the presence of integrated transgenes in the host genome, contributing to the risk for undesired genotoxicity and tumorigenesis. Here, we describe the advanced transgene-free generation of iNSCs from human urine-derived cells (HUCs) by combining a cocktail of defined small molecules with self-replicable mRNA delivery. The established iNSCs were completely transgene-free in their cytosol and genome and further resembled human embryonic stem cell-derived NSCs in the morphology, biological characteristics, global gene expression, and potential to differentiate into functional neurons, astrocytes, and oligodendrocytes. Moreover, iNSC colonies were observed within eight days under optimized conditions, and no teratomas formed in vivo, implying the absence of pluripotent cells. This study proposes an approach to generate transplantable iNSCs that can be broadly applied for neurological disorders in a safe, efficient, and patient-specific manner.

Design, Fabrication, and Accuracy of a Novel Noncovering Lock-Mechanism Bilateral Patient-Specific Drill Guide Template for Nondeformed and Deformed Thoracic Spines

2021 ◽  
pp. 155633162199633
Author(s):  
Mehran Ashouri-Sanjani ◽  
Shima Mohammadi-Moghadam ◽  
Parisa Azimi ◽  
Navid Arjmand
Keyword(s):  
Thoracic Spine ◽  
Sagittal Plane ◽  
Ct Scanning ◽  
Entry Point ◽  
In Vivo Studies ◽  
Patient Specific ◽  
Plane Angle ◽  
Severe Scoliosis ◽  
3D Printed

Background: Pedicle screw (PS) placement has been widely used in fusion surgeries on the thoracic spine. Achieving cost-effective yet accurate placements through nonradiation techniques remains challenging. Questions/Purposes: Novel noncovering lock-mechanism bilateral vertebra-specific drill guides for PS placement were designed/fabricated, and their accuracy for both nondeformed and deformed thoracic spines was tested. Methods: One nondeformed and 1 severe scoliosis human thoracic spine underwent computed tomographic (CT) scanning, and 2 identical proportions of each were 3-dimensional (3D) printed. Pedicle-specific optimal (no perforation) drilling trajectories were determined on the CT images based on the entry point/orientation/diameter/length of each PS. Vertebra-specific templates were designed and 3D printed, assuring minimal yet firm contacts with the vertebrae through a noncovering lock mechanism. One model of each patient was drilled using the freehand and one using the template guides (96 pedicle drillings). Postoperative CT scans from the models with the inserted PSs were obtained and superimposed on the preoperative planned models to evaluate deviations of the PSs. Results: All templates fitted their corresponding vertebra during the simulated operations. As compared with the freehand approach, PS placement deviations from their preplanned positions were significantly reduced: for the nonscoliosis model, from 2.4 to 0.9 mm for the entry point, 5.0° to 3.3° for the transverse plane angle, 7.1° to 2.2° for the sagittal plane angle, and 8.5° to 4.1° for the 3D angle, improving the success rate from 71.7% to 93.5%. Conclusions: These guides are valuable, as the accurate PS trajectory could be customized preoperatively to match the patients’ unique anatomy. In vivo studies will be required to validate this approach.

scholarly journals Concomitant control of mechanical properties and degradation in resorbable elastomer-like materials using stereochemistry and stoichiometry for soft tissue engineering

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Mary Beth Wandel ◽  
Craig A. Bell ◽  
Jiayi Yu ◽  
Maria C. Arno ◽  
Nathan Z. Dreger ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Drug Delivery ◽  
Soft Tissue ◽  
Tissue Regeneration ◽  
Biological Tissues ◽  
Soft Tissue Regeneration ◽  
Soft Tissue Engineering ◽  
Degradation Properties ◽  
Enhance Cell Adhesion

AbstractComplex biological tissues are highly viscoelastic and dynamic. Efforts to repair or replace cartilage, tendon, muscle, and vasculature using materials that facilitate repair and regeneration have been ongoing for decades. However, materials that possess the mechanical, chemical, and resorption characteristics necessary to recapitulate these tissues have been difficult to mimic using synthetic resorbable biomaterials. Herein, we report a series of resorbable elastomer-like materials that are compositionally identical and possess varying ratios of cis:trans double bonds in the backbone. These features afford concomitant control over the mechanical and surface eroding degradation properties of these materials. We show the materials can be functionalized post-polymerization with bioactive species and enhance cell adhesion. Furthermore, an in vivo rat model demonstrates that degradation and resorption are dependent on succinate stoichiometry in the elastomers and the results show limited inflammation highlighting their potential for use in soft tissue regeneration and drug delivery.

scholarly journals Development of patient specific, realistic, and reusable video assisted thoracoscopic surgery simulator using 3D printing and pediatric computed tomography images

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Dayeong Hong ◽  
HaeKang Kim ◽  
Taehun Kim ◽  
Yong-Hee Kim ◽  
Namkug Kim
Keyword(s):  
Computed Tomography ◽  
Mechanical Properties ◽  
Fused Deposition Modeling ◽  
Thoracoscopic Surgery ◽  
Clinical Situation ◽  
Patient Specific ◽  
Fused Deposition ◽  
Video Assisted ◽  
Computed Tomography Images ◽  
Video Assisted Thoracoscopic Surgery

AbstractHerein, realistic and reusable phantoms for simulation of pediatric lung video-assisted thoracoscopic surgery (VATS) were proposed and evaluated. 3D-printed phantoms for VATS were designed based on chest computed tomography (CT) data of a pediatric patient with esophageal atresia and tracheoesophageal fistula. Models reflecting the patient-specific structure were fabricated based on the CT images. Appropriate reusable design, realistic mechanical properties with various material types, and 3D printers (fused deposition modeling (FDM) and PolyJet printers) were used to represent the realistic anatomical structures. As a result, the phantom printed by PolyJet reflected closer mechanical properties than those of the FDM phantom. Accuracies (mean difference ± 95 confidence interval) of phantoms by FDM and PolyJet were 0.53 ± 0.46 and 0.98 ± 0.55 mm, respectively. Phantoms were used by surgeons for VATS training, which is considered more reflective of the clinical situation than the conventional simulation phantom. In conclusion, the patient-specific, realistic, and reusable VATS phantom provides a better understanding the complex anatomical structure of a patient and could be used as an educational phantom for esophageal structure replacement in VATS.

scholarly journals Injectable non-leaching tissue-mimetic bottlebrush elastomers as an advanced platform for reconstructive surgery

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Erfan Dashtimoghadam ◽  
Farahnaz Fahimipour ◽  
Andrew N. Keith ◽  
Foad Vashahi ◽  
Pavel Popryadukhin ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Reconstructive Surgery ◽  
Biomedical Applications ◽  
The Body ◽  
Surrounding Tissue ◽  
Curing Time ◽  
Materials Used ◽  
Significant Health

AbstractCurrent materials used in biomedical devices do not match tissue’s mechanical properties and leach various chemicals into the body. These deficiencies pose significant health risks that are further exacerbated by invasive implantation procedures. Herein, we leverage the brush-like polymer architecture to design and administer minimally invasive injectable elastomers that cure in vivo into leachable-free implants with mechanical properties matching the surrounding tissue. This strategy allows tuning curing time from minutes to hours, which empowers a broad range of biomedical applications from rapid wound sealing to time-intensive reconstructive surgery. These injectable elastomers support in vitro cell proliferation, while also demonstrating in vivo implant integrity with a mild inflammatory response and minimal fibrotic encapsulation.

Sign in / Sign up

Export Citation Format

Share Document