scholarly journals Hysteretic Implications for Graded Bed Load Sediment Transport in Symmetrical Hydrograph Flows

2021 ◽  
Vol 9 ◽  
Author(s):  
Le Wang ◽  
Dayu Wang ◽  
Alan Cuthbertson ◽  
Deyu Zhong ◽  
Gareth Pender
Keyword(s):  
Sediment Transport ◽  
Size Class ◽  
Yield Ratio ◽  
Bed Load ◽  
Size Classes ◽  
Sediment Bed ◽  
Load Transport ◽  
Bed Load Transport ◽  
Load Sediment ◽  
Clockwise Hysteresis

Differential parametric values associated with bed load sediment transport, that result at the same discharge levels on the rising and falling limbs of a flood hydrograph, are usually defined as bed load hysteresis. This hysteresis in bed load sediment transport rates is of considerable interest in the field of fluvial hydraulics. Within this study, a series of well-defined, symmetrical hydrograph flows are generated over a graded, mobile sediment bed to fully examine the hysteresis of the resulting bed load sediment transport in terms of the threshold of motion, and differential bed load transport rates and bed load yields during the hydrographs. The experiments are conducted in a titling flume without sediment supply specified at the upstream inlet, thereby representing typical river reach conditions immediately downstream of a dam that are exclusively subject to net in-channel bed degradation from sediment transport initiated during flood events. Our results show that the fractional bed load transport of defined fine, medium and coarse size classes within the graded sediment bed generally display clockwise, no/mixed and counter-clockwise hysteresis patterns, respectively, with clockwise hysteresis most commonly found for the coarse size class mobilised by hydrographs with long durations. By contrast, counter-clockwise hysteresis is usually observed for fine size class transported by hydrographs with short durations. Accordingly, the corresponding reference stresses for each size class vary between different hydrographs and are primarily controlled by the hydrograph flashiness (i.e. unsteadiness) and magnitude (i.e. total water work). Moreover, it is shown that the hysteresis effect, particularly for those size classes and hydrograph combinations that result in clockwise and counter-clockwise behaviour, should be fully accounted for when reproducing bed load transport rates using separate-limb based method. Finally, we investigate the relative fractions of the overall bed load yields generated during the rising and falling limbs of all symmetrical hydrographs (i.e. the bed load yield ratio), which are found to be primarily dependent on bed load transport hysteresis. Finally, the relationship between the bed load yield ratio and the ratio of reference stresses for the fractional sediment motion of each size class on both limbs is found to follow a power law.

Lagrangian model of bed-load transport in turbulent junction flows

2011 ◽  
Vol 666 ◽  
pp. 36-76 ◽  
Author(s):  
CRISTIAN ESCAURIAZA ◽  
FOTIS SOTIROPOULOS
Keyword(s):  
Sediment Transport ◽  
Field Experiments ◽  
Computational Study ◽  
Transport Processes ◽  
Lagrangian Model ◽  
Bed Load ◽  
Particle Interactions ◽  
Load Transport ◽  
Bed Load Transport ◽  
Load Sediment

Motivated by the need to gain fundamental insights into the mechanisms of bed-load sediment transport in turbulent junction flows, we carry out a computational study of Lagrangian dynamics of inertial particles initially placed on the bed upstream of a surface-mounted circular cylinder in a rectangular open channel (Dargahi, J. Hydraul. Engng, vol. 116, 1990, pp. 1197–1214). The flow field at Re = 39000 is simulated using the detached eddy simulation (DES) approach (Spalart et al., In Advances in DNS/LES, ed. C. Liu & Z. Liu, 1997, Greyden), which has already been shown to accurately resolve most of the turbulent stresses produced by the low-frequency, bimodal fluctuations of the turbulent horseshoe vortex (Paik et al., J. Hydraul. Engng, vol. 131, 1990, pp. 441–456; Escauriaza & Sotiropoulos, Flow Turbul. Combust., 2010, in press). The trajectory and momentum equations for the sediment particles are integrated numerically simultaneously with the flow governing equations assuming one-way coupling and neglecting particle-to-particle interactions (dilute flow) but taking into account bed–particle interactions and the effects of the instantaneous hydrodynamic forces induced by the resolved fluctuations of the coherent vortical structures. The computed results show that, in accordance with the simulated clear-water scour condition (i.e. the magnitude of the particle stresses is near the threshold of motion), the transport of sediment grains is highly intermittent and exhibits essentially all the characteristics of bed-load sediment transport observed in laboratory and field experiments. Groups of sediment grains are dislodged from the bed simultaneously in seemingly random bursting events and begin to move, saltating or sliding along the bed. Furthermore, particles that are not entrained into the bed-load layer are found to form streaks aligned with near-wall vortices around the cylinder. The global transport of particles is studied by performing a statistical analysis of the bed-load flux to reveal scale-invariance of the process and multifractality of particle transport as the overall effect of the coherent structures of the flow. A major finding of this work is that a relatively simple Lagrangian model coupled with a coherent-structure resolving simulation of the turbulent flow is able to reproduce the sediment dynamics observed in multiple experiments performed under similar conditions, and provide fundamental information on the initiation of motion and the multifractal nature of bed-load transport processes. The results also motivate the development of new Eulerian bed-load transport models that consider unsteady conditions and incorporate the intermittency of the unresolved scales of sediment motion.

scholarly journals Grain shape effects in bed load sediment transport

2021 ◽  
Author(s):  
Eric Deal ◽  
Jeremy Venditti ◽  
Santiago Benavides ◽  
Ryan Bradley ◽  
Qiong Zhang ◽  
...  
Keyword(s):  
Sediment Transport ◽  
Grain Shape ◽  
Sediment Flux ◽  
Bed Load ◽  
Flume Experiments ◽  
Natural Sediment ◽  
Shape Effects ◽  
Load Transport ◽  
Bed Load Transport ◽  
Load Sediment

Bed load sediment transport, in which wind or water flowing over a bed of sediment causes grains to roll or hop along the bed, is a critically important mechanism in contexts ranging from river restoration to planetary exploration. Despite its widespread occurrence, predictions of bed load sediment flux are notoriously imprecise. Many studies have focused on grain size variability as a source of uncertainty, but few have investigated the role of grain shape, even though shape has long been suspected to influence transport rates. Here we show that grain shape can modify bed load transport rates by an amount comparable to the scatter in many sediment transport data sets. We develop a theory that accounts for grain shape effects on fluid drag and granular friction and predicts that the onset and efficiency of bed load transport depend on the mean drag coefficient and bulk friction coefficient of the transported grains. Laboratory flume experiments using a variety of grain shapes confirm these predictions. We propose a shape-independent sediment transport law that collapses our experimental measurements onto a single trend, allowing for more accurate predictions of sediment transport and helping reconcile theory developed for spherical particle transport with the behavior of natural sediment grains.

scholarly journals Regression analysis between sediment transport rates and stream discharge for the Nestos River, Greece

2013 ◽  
Vol 14 (3) ◽  
pp. 362-370
Keyword(s):  
Sediment Transport ◽  
Suspended Load ◽  
Bed Load ◽  
Regression Curve ◽  
Degree Polynomial ◽  
Stream Discharge ◽  
Nestos River ◽  
Polynomial Curve ◽  
Load Transport ◽  
Bed Load Transport

Systematic measurements of sediment transport rates and water discharge were conducted in the Nestos River (Greece), at a place located between the outlet of Nestos River basin and the river delta. This basin area is about 838 km2 and lies downstream of the Platanovrysi Dam. Separate measurements of bed load transport and suspended load transport were performed at certain cross sections of the Nestos River. In this study, relationships between sediment transport rates and stream discharge for the Nestos River are presented. A nonlinear regression curve (4th degree polynomial curve; r2 equals 0.62) between bed load transport rates and stream discharge, on the basis of 63 measurements, was developed. In addition, a nonlinear regression curve (5th degree polynomial curve; r2 equals 0.95) between suspended load transport rates and stream discharge, on the basis of 65 measurements, was developed. The relatively high r2 values indicate that both bed load transport rates and, especially, suspended load transport rates can be predicted as a function of the stream discharge in the Nestos River. However, the reliability of the regression equations would have been higher if more measured data were available.

scholarly journals Analisa Angkutan Sedimen Pada Hulu Bendung Aepodu Kabupaten Konawe Selatan

2021 ◽  
Vol 2 (1) ◽  
pp. 1-7
Author(s):  
Ramadhan Hidayat Putra ◽  
Amad Syarif Syukri ◽  
Catrin Sudarjat ◽  
Vickky Anggara Ilham
Keyword(s):  
Sediment Transport ◽  
River Flow ◽  
Suspended Load ◽  
Bedload Transport ◽  
Bed Load ◽  
Average Flow ◽  
Load Transport ◽  
Bed Load Transport ◽  
Transport Analysis

Research on Aepodu Weir Sediment Transport Analysis in South Konawe District, based on observations in the field, Aepodu Weir hasa sediment buildup that has now exceeded the height of the weirlight house. The purpose of the study was to analyze the magnitudeof Aepodu river flow and to analyze the amount of sedimenttransport that occurred in the Aepodu dam. The method used todetermine the amount of bed load transport uses stchoklitscht, whilefor transporting suspended load using forcheimer.The results of the analysis of the average flow of the Aepodu riverwere 3,604 m3/ second. Sediment transport that occurs in Aepoduweir is Bedload transport (Qb) of 291625.771 tons / year, andsuspended load transport (Qs) of 16972,423 tons / year, so that thetotal sediment transport (QT) is 308598,194 tons / year.

scholarly journals Sediment Bed-Load Transport: A Standardized Notation

Geosciences ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 368
Author(s):  
Ulrich Zanke ◽  
Aron Roland
Keyword(s):  
Shear Stress ◽  
Critical Shear Stress ◽  
Basic Structure ◽  
Structural Formula ◽  
Bed Load ◽  
Viscous Effects ◽  
Data Set ◽  
Sediment Bed ◽  
Load Transport ◽  
Bed Load Transport

Morphodynamic processes on Earth are a result of sediment displacements by the flow of water or the action of wind. An essential part of sediment transport takes place with permanent or intermittent contact with the bed. In the past, numerous approaches for bed-load transport rates have been developed, based on various fundamental ideas. For the user, the question arises which transport function to choose and why just that one. Different transport approaches can be compared based on measured transport rates. However, this method has the disadvantage that any measured data contains inaccuracies that correlate in different ways with the transport functions under comparison. Unequal conditions also exist if the factors of transport functions under test are fitted to parts of the test data set during the development of the function, but others are not. Therefore, a structural formula comparison is made by transferring altogether 13 transport functions into a standardized notation. Although these formulas were developed from different perspectives and with different approaches, it is shown that these approaches lead to essentially the same basic formula for the main variables. These are shear stress and critical shear stress. However, despite the basic structure of these 13 formulas being the same, their coefficients vary significantly. The reason for that variation and the possible effect on the bandwidth of results is identified and discussed. A further result is the finding that not only shear stress affects bed-load transport rates as is expressed by many transport formulas. Transport rates are also significantly affected by the internal friction of the moving sediment as well as by the friction fluid-bed. In the case of not fully rough flow conditions, also viscous effects and thus the Reynolds number becomes of importance.

scholarly journals Impact of the regularity of the sediment bed on bed-load transport

PAMM ◽  
2016 ◽  
Vol 16 (1) ◽  
pp. 583-584
Author(s):  
Ramandeep Jain ◽  
Bernhard Vowinckel ◽  
Jochen Fröhlich
Keyword(s):  
Bed Load ◽  
Sediment Bed ◽  
Load Transport ◽  
Bed Load Transport

scholarly journals A Sediment Transport Model for Straight Alluvial Channels

1976 ◽  
Vol 7 (5) ◽  
pp. 293-306 ◽  
Author(s):  
Frank Engelund ◽  
Jørgen Fredsøe
Keyword(s):  
Sediment Transport ◽  
Transport Model ◽  
Suspended Load ◽  
Empirical Models ◽  
Bed Load ◽  
Alluvial Channels ◽  
Physical Processes ◽  
Sediment Transport Model ◽  
Load Transport ◽  
Bed Load Transport

The paper presents a simple mathematical model for sediment transport in straight alluvial channels. The model, which is based on physical ideas related to those introduced by Bagnold (1954), was originally developed in two steps, the first describing the bed load transport (Engelund 1975) and the second accounting for the suspended load (Fredsøe and Engelund 1976). The model is assumed to have two advantages as compared with empirical models, first it is based on a description of physical processes, secondly it gives some information about the quantity and size of the sand particles in suspension and the bed particles.

scholarly journals A Shear Reynolds Number-Based Classification Method of the Nonuniform Bed Load Transport

Water ◽  
2019 ◽  
Vol 11 (1) ◽  
pp. 73 ◽  
Author(s):  
Gergely T. Török ◽  
János Józsa ◽  
Sándor Baranya
Keyword(s):  
Reynolds Number ◽  
Sediment Transport ◽  
Comparative Assessment ◽  
Bed Load ◽  
Laboratory Measurements ◽  
Strong Variation ◽  
Load Transport ◽  
Bed Load Transport ◽  
Novel Method ◽  
Bed Material

The aim of this study is to introduce a novel method which can separate sand- or gravel-dominated bed load transport in rivers with mixed-size bed material. When dealing with large rivers with complex hydrodynamics and morphodynamics, the bed load transport modes can indicate strong variation even locally, which requires a suitable approach to estimate the locally unique behavior of the sediment transport. However, the literature offers only few studies regarding this issue, and they are concerned with uniform bed load. In order to partly fill this gap, we suggest here a decision criteria which utilizes the shear Reynolds number. The method was verified with data from field and laboratory measurements, both performed at nonuniform bed material compositions. The comparative assessment of the results show that the shear Reynolds number-based method operates more reliably than the Shields–Parker diagram and it is expected to predict the sand or gravel transport domination with a <5% uncertainty. The results contribute to the improvement of numerical sediment transport modeling as well as to the field implementation of bed load transport measurements.

scholarly journals BED LOAD TRANSPORT DUE TO NON-LINEAR WAVE MOTION

1988 ◽  
Vol 1 (21) ◽  
pp. 133 ◽  
Author(s):  
Hitoshi Tanaka
Keyword(s):  
Sediment Transport ◽  
Wave Motion ◽  
Surf Zone ◽  
Function Theory ◽  
Transport Rate ◽  
Bed Load ◽  
Linear Wave ◽  
Wave Flume ◽  
Load Transport ◽  
Bed Load Transport

The bed load transport rate due to wave motion is measured in a wave flume. The modified stream function theory of the author ( Tanaka (1988) ) is applied to the formulation of the sediment transport rate in order to include the non-linearity. The proposed formula predicts well except near the surf zone where the effect of the acceleration plays an important role.

Sign in / Sign up

Export Citation Format

Share Document